Sharp MX-3050N / MX-3060N / MX-3070N / MX-3550N / MX-3560N / MX-3570N / MX-4050N / MX-4060N / MX-4070N (serv.man29) User Manual / Operation Manual ▷ View online
16
BEFORE USING THE MACHINE
PLACING ORIGINALS
The automatic document feeder can be used to automatically scan many originals at once, and this saves you the
trouble of manually feeding each original.
For originals that cannot be scanned using the automatic document feeder, such as a book or a document with notes
attached, use the document glass.
trouble of manually feeding each original.
For originals that cannot be scanned using the automatic document feeder, such as a book or a document with notes
attached, use the document glass.
USING THE AUTOMATIC DOCUMENT FEEDER
When using the automatic document feeder, place the originals in the document feeder tray.
Make sure an original has not been placed on the document glass.
Make sure an original has not been placed on the document glass.
USING THE DOCUMENT GLASS
Take care that your fingers are not pinched when closing the automatic document feeder.
After placing the original, be sure to close the automatic document feeder. If left open, parts outside of the original will be
copied black, causing excessive use of toner.
After placing the original, be sure to close the automatic document feeder. If left open, parts outside of the original will be
copied black, causing excessive use of toner.
Adjust the original guides to
the width of the originals.
the width of the originals.
Place the originals face up with the edges aligned
evenly.
The indicator line indicates approximately
how many originals can be placed. The placed
originals must not be higher than this line.
evenly.
The indicator line indicates approximately
how many originals can be placed. The placed
originals must not be higher than this line.
Place the original face down.
Align the top left corner of the
original with the tip of the
mark in the far left corner of the
glass.
Align the top left corner of the
original with the tip of the
mark in the far left corner of the
glass.
Place the original
face down.
face down.
To place a thick original such as a
book, push up the far edge of the
automatic document feeder and then
close the automatic document feeder
slowly.
book, push up the far edge of the
automatic document feeder and then
close the automatic document feeder
slowly.
BEFORE USING THE MACHINE
17
LOADING PAPER
NAMES AND LOCATIONS OF TRAYS
The names of the trays are as follows.
Setting orientation of the print side
The setting orientation varies for the print side of paper, depending on the tray used. For "Letter Head" and
"Pre-Printed", set the paper in the reverse orientation.
Place with the print side facing the direction indicated below.
"Pre-Printed", set the paper in the reverse orientation.
Place with the print side facing the direction indicated below.
Tray
In normal status
With letter head or pre-printed paper set
Trays 1 - 4
Facing up
Facing down
Bypass tray
Facing down
Facing up
(1)
(2)
(3)
(4)
(2)
(3)
(4)
(5)
(6)
(7)
(1) Tray 1
(2) Tray 2 (when a stand/550/2x550/3x550/
550&2100 sheet paper drawer is installed)
(3) Tray 3 (when a stand/2x550/3x550 sheet
paper drawer is installed)
(4) Tray 4 (when a stand/3x550 sheet paper
drawer is installed)
(5) Tray 3 (when a stand/550&2100 sheet paper
drawer is installed)
(6) Tray 4 (when a stand/550&2100 sheet paper
drawer is installed)
(7) Bypass tray
18
BEFORE USING THE MACHINE
LOAD PAPER INTO THE TRAY 1 - 4
1
Pull out the paper tray.
Gently pull the tray out until it stops.
To load paper, go to step 3. To load a different size of
paper, go to the next step.
To load paper, go to step 3. To load a different size of
paper, go to the next step.
2
Adjust guide plates A and B to match
the longitudinal and transversal
dimensions of the paper to be loaded.
the longitudinal and transversal
dimensions of the paper to be loaded.
• The guide plates A and B are slidable. Squeeze the
separator plate lever and slide to the desired paper size.
Adjust to the non-standard paper size so that the paper
will not be too loose or too tight.
Adjust to the non-standard paper size so that the paper
will not be too loose or too tight.
• To load SRA3 paper, the position of the guide must be
adjusted. For details, see the User's Manual.
3
Insert the paper into the tray.
Load the paper with the print side facing up. The stack must
not be higher than the indicator line.
Fan the paper well before loading it. Otherwise, multiple
sheets may feed at once and cause a misfeed.
not be higher than the indicator line.
Fan the paper well before loading it. Otherwise, multiple
sheets may feed at once and cause a misfeed.
4
Gently push the paper tray into the
machine.
machine.
Push the tray firmly all the way into the machine slowly.
A
B
BEFORE USING THE MACHINE
19
LOADING PAPER IN OTHER TRAYS
Bypass tray
Loading envelopes
Only the front side of envelopes can be printed or copied on. Place the front side facing down.
Fold the flap and make a sharp crease at the fold.
Only the front side of envelopes can be printed or copied on. Place the front side facing down.
Fold the flap and make a sharp crease at the fold.
1
Open the bypass tray.
When loading paper larger than 8-1/2" x 11"R or A4R, pull
out the extension guide.
Pull the extension guide all the way out.
out the extension guide.
Pull the extension guide all the way out.
2
Load the paper with the print side
facing down.
facing down.
Insert the paper along the bypass tray guides all the way into
the bypass tray until it stops slowly.
The paper must not exceed the maximum number of sheets
and must not be higher than the indicator line.
the bypass tray until it stops slowly.
The paper must not exceed the maximum number of sheets
and must not be higher than the indicator line.
3
Set the bypass tray guides correctly to
the width of the paper.
the width of the paper.
Adjust the bypass tray guides so that they slightly contact
the loaded paper.
the loaded paper.
Click on the first or last page to see other MX-3050N / MX-3060N / MX-3070N / MX-3550N / MX-3560N / MX-3570N / MX-4050N / MX-4060N / MX-4070N (serv.man29) service manuals if exist.