Sharp MX-3050N / MX-3060N / MX-3070N / MX-3550N / MX-3560N / MX-3570N / MX-4050N / MX-4060N / MX-4070N (serv.man2) Handy Guide ▷ View online
CONSUMABLES
SHARP
10
TRANSFER SECTION:
MX-30x0N MX-35x0N MX-40x0N
MX-5070N
MX-6070N
MX-6070N
Product Code
Description
Approx. Life
MX-607B1
Primary Transfer Belt Kit
250k
300k
300k
300k
MX-607TL
Primary Transfer Blade Kit:-
Primary Transfer Blade.
Cleaning Roller
Cleaning Roller
250k
300k
300k
300k
MX-607U2
Secondary Transfer Roller Kit
250k
300k
300k
300k
PERIPHERALS:
MX-SCX1
Staple Cartridge (for MX-FN27/FN28)
5000 staples (x 3)
MX-SC11
Staple Cartridge (for MX-FN30/FN31)
5000 staples (x 3)
MX-SC12
Saddle Staple Cartridge (for MX-FN31)
2000 staples (x 4)
AR-SC2
Saddle/Staple Cartridge (for MX-FN29)
5000 staples (x 3)
AR-SV1
Stamp Cartridge (for AR-SU1 Stamp Unit)
2 cartridges
SERVICE ROTATION UNITS:
MX-607U1
Primary Transfer Belt Unit (30/35/40)
x
MX-608U1
Primary Transfer Belt Unit (50/60)
x
x
x
MX-407FU
Fusing Unit 230V (30/35/40)
x
MX-607FU
Fusing Unit 230V (50/60)
x
x
x
Note:
Consumable life may vary depending on the document density, temperature, humidity and machine
operation.
Consumable life may vary depending on the document density, temperature, humidity and machine
operation.
SHARP
INITIAL SETUP
11
DEVELOPER SETUP:
From April 2016 production onwards, CMYK Developer is pre-installed by the factory
therefore, Sim25-02 Auto Developer Adjustment should not be executed.
It is recommended to execute Sim25-01 (Developer Stir), prior to installing toner.
therefore, Sim25-02 Auto Developer Adjustment should not be executed.
It is recommended to execute Sim25-01 (Developer Stir), prior to installing toner.
Only execute Sim25-02 if CMYK Developer has not been pre-installed.
Clean LSU Dust Proof Glass.
TONER INSTALLATION & REPLENISHMENT:
Install CMYK Toner Cartridges:
Caution:
DO NOT open any Exterior Cover, Power OFF/ON or enter Simulation Mode during
Initial Toner Replenishment.
DO NOT open any Exterior Cover, Power OFF/ON or enter Simulation Mode during
Initial Toner Replenishment.
PRODUCT ACTIVATION & FIRMWARE UPGRADE:
Activation of Optional Products:
System Settings – Common Settings – Product Key.
Sim 22-05 Check Firmware Version(s):
Upgrade to latest version.
INITIAL SETUP:
Sim 26-01
Right Exit Tray Installation: Yes/No.
Sim 26-02
LCC Installation (Paper Size): A4/Letter.
Sim 26-06
Machine Destination check.
Sim 26-35
Set Multi Error Counter: Set to 1 (Multi Count).
Sim 26-50
Long Paper Support (up to 1300mm): 0 = Disable, 1 = Enable.
Sim 26-52
Non Printed Paper Counter Set-up.
Sim 55-01
Primary Transfer Belt lubrication
[MX-5070N/6070N only]:
Check SSW 12-4 is set to 1 (enable lubrication at specific interval).
Check SSW 27-4 is set to 1 (force lubrication @ maintenance).
Note: Above SSW settings are applied when PCU v05.00.Z1.00 is installed.
Sim 55-03
Process Mixed Size Pages (orientation) when Printing in Duplex:
SSW 3-6, 0 = Disable, 1 = Enable.
Sim 55-03
PDF/PS Preview Thumbnail for Direct Print Function:
SSW 34-3, 0 = Disable, 1 = Enable.
Add PANTONE® Colour LUT
Service WebPage – Output Profile Settings – Spot Colour Table Settings;
Upload PANTONE® LUT for CR4 series.
Adjust Date/Time (Inc. Daylight Saving setting):
System Settings – Common Settings – Clock Adjust.
INITIAL SETUP
SHARP
12
INITIAL SETUP [CONT’D]
Keyboard Language Setting:
System Settings – Common Settings – Default Keyboard Setting.
Paper Size & Type Settings:
System Settings – Common Settings – Paper Tray Settings.
Set cassette size by adjusting the guides in the cassette.
PRINT IMAGE POSITION & BK MAGNIFICATION:
Check Print Image Off Centre & Lead Edge position - Use Sim 50-10:-
Inside dimension of the printed halftone must be 240±0.5mm.
Lead edge void area 3.0 ± 1.0mm.
Rear edge void area 2.0mm - 5.0mm.
Front & Rear Void areas 2.0 ± 2.0mm.
Lead edge void area 3.0 ± 1.0mm.
Rear edge void area 2.0mm - 5.0mm.
Front & Rear Void areas 2.0 ± 2.0mm.
If NG, perform the following adjustments as required:-
Manual Adjustment:
Sim 50-10
BK MAG / Image Off Centre Adjustment (All Trays).
Sim 50-05
Printer Lead Edge & Void Adjust.
Automatic Adjustment:
Sim 50-28
BK MAG ADJ (Main Scan Mag).
SETUP/PRINT ADJ (Lead, Offset or All).
IMAGE SKEW & COLOUR REGISTRATION
Sim 50-22
Colour Registration/Skew & OPC Drum Phase Adjustment:
Check/Adjust SKEW (CMY) so value is Close to 0 as possible (Result=OK).
HALFTONE COLOR CALIBRATION
Sim 46-74
Engine & Printer Colour Calibration:
Select FACTORY Mode.
IMAGE QUALITY CHECK [COPY & PRINT]
Check Image Quality – Density, Magnification, Lead Edge & Void.
If NG, perform the following adjustments as required:
F/R Evenness Adjustment:
Sim 61-13
F/R Evenness Correction Data Clear
Sim 61-11
F/R Evenness Correction Adjustment
Note: Sim 46-74 must be executed after F/R adjustment is performed.
Copy Density Manual Adjustment:
Sim 46-01
Copy Density Adjust. (Colour).
Sim 46-02
Copy Density Adjust. (B/W).
Sim 46-09
SPF Copy Density Adjust.
SHARP
INITIAL SETUP
13
IMAGE QUALITY CHECK [COPY & PRINT]
Print Image Manual Adjustment (Lead Edge, Void, Off Centre etc.):
Sim 48-01
Magnification Adjustment (OC & SPF).
Sim 50-01
Lead/Rear Edge, Loss & Void Adjust.
Sim 50-12
OC & SPF Off Centre Adjust.
Check Print Image Quality:
Sim 64-05
PCL Density Test Page
Sim 64-06
PS Density Test Page
PERIPHERAL / OPTION CONFIGURATION
FAX OPTION – MX-FX15
Sim 66-02
Fax SW Setting (Destination).
Sim 66-10
Fax Memory Clear.
Sim 66-39
Fax Destination Setting.
FINISHER OPTION – MX-FN27/28/29/30/31
Sim 03-10
Saddle Fold/Staple Position Adjustment [MX-FN29/31 only]
Sim 26-65
Finisher Alarm Mode:-
Limit number of Copies in staple mode (ON/OFF).
Limit the number of sets loaded in the saddle staple (ON/OFF).
**Limit load of folded paper on paper exit and limit load on 50-sheet
Staple saddle finisher are set in SADDLE COPIES.
EXTERNAL ACCOUNTING MODULE – MX-AMX3
Sim 55-03
Auto clear function before Copy job execution:-
SSW 1-5
0 = Disable, 1 = Enable.
Sim 55-03
Continuous print mode (job queuing for OSA):-
SSW 24-7
0 = Disable, 1 = Enable.
MFP DATA BACKUP
Sim 22-06
Data Simulation Print
Device Clone & Storage Backup
Sim 56-01
Backup EEPROM Data to HDD
Click on the first or last page to see other MX-3050N / MX-3060N / MX-3070N / MX-3550N / MX-3560N / MX-3570N / MX-4050N / MX-4060N / MX-4070N (serv.man2) service manuals if exist.