DOWNLOAD Sharp MX-2640N / MX-2640NR / MX-2640FN / MX-3140N / MX-3140NR / MX-3140FN / MX-3640N / MX-3640NR / MX-3640FN (serv.man184) Service Manual ↓ Size: 25.6 KB | Pages: 4 in PDF or view online for FREE

 

 
 
 

 

DIGITAL FULL COLOR COPIER(OPTION) : MX-FR41U 

No.  : CCE-1173

Date : Aug. 1, 2013

 

C

1/4 

SHARP CORPORATION

 

1. Model Name: 

MX-FR41U(Option for MX-2640N/3140N/3640N) 

 

2. Description: 

Upgrade of ICUM and ICU-ROM 

From August 2013 production 

ROM Control No. 

ICUM 

ICU 

B00 0202Ad 

0202Ad 

  * ROM version above is the version described in the ROM management label.    Check that the   
    actual version is: ICUM (MAIN): 02.02.Ad.00/ICUM(SUB): 02.02.A2.00/ICU(MAIN):   
  02.02.Ad.00/ICU(BOOT): 01.00.Ad.00/ICU(SUB): 01.03.A2.0a/LANGUAGE: 01.11.S1.00/ 
    UICONTENTS: 02.02.Ad.00 by SIM22-5.   

    Item of change: See the attached sheet 

  Note) This report is a T/R for the Data Security Kit Option, corresponding to the general   
              T/R No.CCE-1162.   

 

 

 

 

ROM Version Combination History Table 

No. 

ROM control No. 

ICUM 

ICU 

Action 

T/R No. 

(1) A01  0121Ad 

0121Ad 

2013/4 

CCE-1140 

 

 

 
 
 

2/4 

[Description] 

No. Item 

Details 

1 Specification 

Implementation of the support for AirPrint which is provided by Apple Inc. to enable 
wireless print with iOS terminals such as iPhone/iPad. 

2 Specification 

Implementation of support for cloud portal 

3 Specification 

Modification of F6-00. The symptoms listed below appeared after switch on a machine or 
while recovering from 1W power-save mode: 
 
- Fax job is prohibited, even though other jobs are allowed. 
- F6-00 error is displayed on any screen other than Home screen. 
- Display of F6-00 error is cleared by pressing OK key, but it is displayed again at the 
timing of auto-clear.   

4 Specification 

Modification of machine lockup which occurred at the time of startup displaying "Please 
wait." 

5 Specification 

Modification of U2-42 error. The error occurred due to the limitation of the number of file 
allowed to open at the same time for Scan to SMB etc. 

6 Specification 

Modification of failure to perform Scan to SMB etc. with an error message "Job queue 
memory is full." 

7 Specification 

Change of the time-out timer for read / write HDD from 10 seconds (with 3 retries) to 22 
seconds (with 2 retries). 

8 Specification 

Implementation of modification for E7-03 which occurred if PIO command (standby 
command) failed even once. 

9 Specification 

Modification of failure to activate card reader by Equitrac with the machine with built-in 
keyboard 

10 UI 

Modification of failure to display Preview. The problem occurred after machine kept 
working for 25 days without turning off (or 1W power-save mode). 

11 UI 

Modification of lock up with the message "Please wait" at the time of log-in to MFP. The 
problem occurred when the MFP was set to Device account mode and Document Filing 
was set as default screen. 

12 

UI 

Modification of failure to delete Document Filing data in a batch 

13 

Web Page 

Modification of the error during the connection test in LDAP Settings on web page 

14 Image 

Send 

When Forward Received Fax Data setting was enabled, transfer processing (job deletion 
processing after the transfer) did not complete properly that this job was recognized 
incomplete. As a result, some problems occurred that for example, receiving lamp stayed 
ON. This problem has been corrected. 

15 Image 

Send 

Modification of machine lockup which occurred after reboot in case the power delivery 
discontinued while receiving Fax data using more than one line 

16 Image 

Send 

If multiple Fax lines were terminated at the same time due to an error while each line was 
being used to perform Fax data communication, the communication of only one line was 
not completed (even thought the line became inactive). This problem has been corrected.

17 

Image Send 

Modification of machine lock up while receiving and printing Fax data 

18 Image 

Send 

Modification of following problems due to the inclusion of "data transfer using OSA" as one 
of the judgement condition for job deletion (data deletion). As a result, jobs were deleted 
during the operation/processing of data transfer in OSA. 
 
- Jobs were deleted after the data transfer that unable to print. 
- Available memory never went back to 100% but remained 99% (because the job deletion 
was performed under improper condition that garbage data remained*). 
*In this case image memory clear in Sim 66-1 is required. 

19 

Image Send 

Modification of failure to output received Internet Fax data from particular models 

 

 
 
 

3/4 

 

No. Item 

Details 

20 Image 

Send 

While reconnecting to the server with support for passive mode after failing to the 
connection in active mode, the communication was not allowed for a while depends on the 
server. In that case, the data transmission to FTP site was not allowed until the recovery. A 
Soft SW has been added as a countermeasure so that the connection in passive mode is 
allowed in the first place. 
 
  FAX soft SW (in Sim66-1) 
  SW No. 96    Bit No. 4 
 
0: Connection in active mode (default) 
1: Connection in passive mode 

21 Image 

Send 

Modification of failure to transmit the data in proper size. The data transmitted were slightly 
smaller than actual size if Inch size paper was scanned. 

22 Printer 

Modification of failure to print out the PS data in case [Network Settings] -> [Print Port 
Settings] -> [Use Banner] on LPD tag on web page was enabled. 

23 Printer 

Modification of the problems with output of the PS data such as taking too long to print out 
large volume data and disappearance of spooled data. 

24 

Printer 

Modification of machine lockup while printing PS data with many pages 

25 

Printer 

Modification of an error printing particular file from Mac OS 

26 Printer 

Modification of a failure to print custom size data in duplex in case the data were output in 
Document Filing. 

27 

Printer 

Modification of garbled characters while printing particular PDF file. 

28 Printer 

Modification of machine lockup. If particular Corel Draw 11 file was printed via PCL 6 
driver, the machine locked up and was unable to print. 

29 Printer 

Modification of print in solid black around logo mark in case the data were printed from the 
system called AddVantage. 

30 Printer 

Modification of output of improper number of copies in case "Separator page 
(sysprint.sep)" is set. 

31 Printer 

Modification 

of 

the 

failure to print out from SAP 

32 

Network 
communication 

Modification of a failure to open tiff file with Photo viewer for Windows 7. The problem 
occurred if the file was stored to NAS for main unit using "Settings for HDD Storing of 
Received Data" feature etc.   

33 

Network 
communication 

Modified to perform a security check input limit item type the following security key every. 
  When type = WPA security 
    - Can be registered as a string: 5 digits / 13 digits   
    - Can be registered only Hex: 10 digits / 26 digits   
    - No registration other than the above 
 
  When type = WPA security 
    - Can be registered as a string: 8-digit to 63-digit 
    - Can be registered only Hex: 64 digits 
    - No other registration 

34 OSA 

Modification of an "out of memory" error. An error message "The memory becomes full." 
was displayed when mySharp was displayed in OSA mode. 

35 Option 

Change of default URL in Web Browse from "http://www.sharp-world.com/" to 
"about:blank" (blank page) 

36 Others 

Modification of erasure of Address Book data. It occurred during the auto recovery process 
of HDD (remounting procedures after "WatchDogError"). As a countermeasure, the 
machine stops for E7-03(09) error instead of the remounting for auto recovery. 

 

 
 
 

4/4 

 

No. Item 

Details 

37 Others 

When "Repeat Layout (Fixed Repeat)" in Copy Special Modes is selected and also 
"Original size: A4/A4R, Paper size: A3, Repeat Number: 2" is set up, the auto calculated 
magnification becomes 100% and then the image of A4 original can equally be placed on 
A3 paper as a result. 
 
* This feature is enabled/disabled in the Soft SW (in Sim55-3_No.30-7). For Taiwan, this 
SW is set to 1 (ON) as default and for other destinations, it is set to 0 (OFF) as default. 

38 Others 

Modification of a failure to transfer Document Filing data to other location in case the data 
were backup from old models. 

39 

Others 

Support for counting function by coverage and Utility counting function