DOWNLOAD Sharp MX-2314N (serv.man3) Service Manual ↓ Size: 91.35 KB | Pages: 2 in PDF or view online for FREE

Model
MX-2314N (serv.man3)
Pages
2 Few pages! See other manuals at the bottom of the first or last page.
Size
91.35 KB
Type
PDF
Document
Handy Guide
Brand
Device
Copying Equipment / GENERAL PROCEDURE FOR COLOUR CALIBRATION SET-UP
File
mx-2314n-sm3.pdf
Date

Sharp MX-2314N (serv.man3) Handy Guide ▷ View online

 
 
 
 
 
 
 
 
 
 
 
 
 
1. Model Name 
MX-C310 – MX-5141 
 
2. Description 
This is a Colour Calibration procedure to allow the MFP to perform at the best level of 
copy quality for the product. The procedure should be followed in order. It is split into 
three levels, black should be performed after every call, black and blue should be 
performed after a preventative maintenance call and black blue and red should be 
performed if a problem still exists. 
 
Black: All call procedure 
Blue: After preventative maintenance 
Red: If there are still problems with CQ 
 
3. Tools Required 
 
SERVICE MANUAL 
INSTALLATION MANUAL 
MONDI COLOUR COPY PAPER 
A4 100g/m² 
IMAGE DENSITY SENSOR CALIBRATION JIG 
UKOG-0318FCZZ 
SHARP COLOUR TEST CHART 
UKOG-0326FCZZ 
SIT CHART 
UKOG-0280FCZ1 
SHARP GREY CHART 
UKOG-0162FCZZ 
 
 
1. Ensure that the MFP is at the latest level of firmware according to Sharp (UK) Technical website (SIM 22-05) 
 
2.
 
Ensure all Process Voltages for DV Bias, Main Charge Grid Voltage and Transfer Voltage are set to the correct 
values (ADJ 1)
 
 
3. Execute simulation 22-06 and ensure on page 2 all settings in SIM 46-01 and SIM 46-02 are set to default 50, also 
ensure that SIM 
**
46-10, SIM46-16 and SIM 46-21 are default to 500 (If these have 
been adjusted they can be reset after calibration) 
 
4. Clean all mirrors, glass, lens, white reference plate and CCD in optics cavity 
 
5. **Use image density sensor calibration jig and execute SIM 44-13 as per service manual (ADJ 2a) 
                                                      #Ensure the sensor is cleaned# 
 
6. Perform black image density sensor and image registration sensor adjustment by executing SIM 44-02 
(This also Calibrates the Colour ID Sensor For CR3.5 Model range below) as per service manual (ADJ 2b)      
                                                      #Ensure the sensor is cleaned# 
 
GENERAL PROCEDURE FOR COLOUR CALIBRATION SET-UP 
         MX Colour Calibration Set-Up 
Date: December 2012 
Model: MX-C310 – MX-5112N 
Ref.: CQ set-up 
Colour: White
 
Page:1 of 2 
 
**
7. Perform black LSU skew adjustment (SIM 61-04) as per service manual (ADJ 3)
 
 
8. Perform Drum Phase/Image Registration/Colour Laser Skew adjustment by executing SIM 50-22 and selecting 
ALL (ADJ 4a) 
 
9. Execute SIM 44-27, clearing half tone process control correction values 
 
10. Execute SIM 44-06, forced execution of process control 
 
11. Execute SIM 44-26, forced execution of half tone image correction 
                                                   
12. Execute SIM  63-11 & choose engine DEF1 default target. 
 
13. Execute SIM  63-08 to match scanner service target to factory target. 
 
14. Execute SIM  67-26  & choose printer DEF1 default target. 
 
15. Execute SIM 67-28 to match printer service target to factory target. 
                                           
 
**16. Calibrate the CCD array by using the SIT chart and executing SIM 63-03 (ADJ 14a)
 
 
17. Ensure good quality A4 colour copy paper is in the machine and perform Auto Colour Calibration by executing 
SIM 46-74 (This simulation performs both the engine and printer calibration 
simultaneously).  
 
18. Place the printed colour patch test page (Figure 1) face down on the glass so that the fine lines are on the left 
hand side, then lay 5 sheets of clean A4 paper on top of the test page. Select “FACTORY” method when calibrating. 
The copy colour balance adjustment is automatically executed and prints the colour balance check page (Figure 2). 
Check for defects, if OK continue to step 15, if not fault find and rectify. 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
19. Select “Execute” again, this time the Printer calibration patch test page (Figure 3) will be printed. Place face 
down on the glass so that the fine lines are on the left hand side, then lay 5 sheets of clean A4 paper on top of the 
test page. Select “FACTORY” method when calibrating. The copy colour balance adjustment is automatically 
executed and prints the colour balance check page (Figure 4). Check for defects, if OK select OK, if not fault find and 
rectify. Colour calibration is now complete. 
 
 
** NO REQUIREMENT ON MX-2310  TO MX-5112 (CR3) / 
** NO REQUIREMENT ON MX-2314 TO MX-5141 (CR3.5) 
 
Figure 1 
Figure 2 
 
Display

Sharp MX-2314N (serv.man3) Handy Guide ▷ Download

  • DOWNLOAD Sharp MX-2314N (serv.man3) Service Manual ↓ Size: 91.35 KB | Pages: 2 in PDF or view online for FREE
  • Here you can View online or download the Handy Guide for the Sharp MX-2314N (serv.man3) in PDF for free, which will help you to disassemble, recover, fix and repair Sharp MX-2314N (serv.man3) Copying Equipment. Information contained in Sharp MX-2314N (serv.man3) Handy Guide (repair manual) includes:
  • Disassembly, troubleshooting, maintenance, adjustment, installation and setup instructions.
  • Schematics, Circuit, Wiring and Block diagrams.
  • Printed wiring boards (PWB) and printed circuit boards (PCB).
  • Exploded View and Parts List.