Sharp MX-2310U / MX-3111U (serv.man22) User Manual / Operation Manual ▷ View online
1-4
BEFORE USING THE MACHINE
Contents
(7)
USB connector (A type)
Supports USB 2.0 (Hi-Speed).
This is used to connect a USB device such as USB
memory to the machine.
For the USB cable, use a shielded cable.
This is used to connect a USB device such as USB
memory to the machine.
For the USB cable, use a shielded cable.
(8)
Keyboard*
Use this as a substitute for the soft keyboard displayed
on the touch panel. When not being used, it can be
stored under the operation panel.
on the touch panel. When not being used, it can be
stored under the operation panel.
☞
KEYBOARD
(page 1-68)
(9)
Tray 1
This holds paper.
☞
TRAY SETTINGS FOR TRAY 1 TO 4
(page 1-30)
(10) Tray 2 (when a paper drawer is installed)*
This holds paper.
☞
TRAY SETTINGS FOR TRAY 1 TO 4
(page 1-30)
(11) Tray 3 (when a paper drawer is installed)*
This holds paper.
☞
TRAY SETTINGS FOR TRAY 1 TO 4
(page 1-30)
(12) Tray 4 (when a paper drawer is installed)*
This holds paper.
☞
TRAY SETTINGS FOR TRAY 1 TO 4
(page 1-30)
* Peripheral device.
(7)
(10)
(9)
(11)
(12)
(8)
1-5
BEFORE USING THE MACHINE
Contents
INTERIOR
(13) Toner cartridges
These contain toner for printing. When the toner runs out
in a cartridge, the cartridge of the colour that ran out must
be replaced.
in a cartridge, the cartridge of the colour that ran out must
be replaced.
☞
REPLACING THE TONER CARTRIDGES
(page 1-61)
(14) Fusing unit
Heat is applied here to fuse the transferred image onto
the paper.
the paper.
(15) Transfer belt
During full colour printing, the toner images of each of the
four colours on each of the photoconductive drums are
combined together on the transfer belt. During black and
white printing, only the black toner image is transferred
onto the transfer belt.
four colours on each of the photoconductive drums are
combined together on the transfer belt. During black and
white printing, only the black toner image is transferred
onto the transfer belt.
(16) Right side cover
Open this cover to remove a misfeed.
(17) Paper reversing section cover
This is used when 2-sided printing is performed. Open
this cover to remove a paper misfeed.
this cover to remove a paper misfeed.
(18) Bypass tray
Use this tray to feed paper manually.
When loading a large sheet of paper, be sure to pull out
the bypass tray extension.
When loading a large sheet of paper, be sure to pull out
the bypass tray extension.
☞
LOADING PAPER IN THE BYPASS TRAY
(page 1-32)
(19) Main power switch
This is used to power on the machine.
When using the fax or Internet fax functions, keep this
switch in the "on" position.
When using the fax or Internet fax functions, keep this
switch in the "on" position.
☞
TURNING THE POWER ON AND OFF
(page 1-15)
(20) Waste toner box
This collects excess toner that remains after printing.
☞
REPLACING THE WASTE TONER BOX
(page 1-64)
(21) Waste toner box release lever
Move this lever when you need to release the waste
toner box lock to replace the waste toner box or clean the
laser unit.
toner box lock to replace the waste toner box or clean the
laser unit.
☞
CLEANING THE LASER UNIT
(page 1-57)
☞
REPLACING THE WASTE TONER BOX
(page 1-64)
(22) Handle
Pull this out and grasp it when moving the machine.
(23) Right cover of paper drawer
(when a paper drawer is installed)
Open this to remove a paper misfeed in tray 2, tray 3 or
tray 4.
Open this to remove a paper misfeed in tray 2, tray 3 or
tray 4.
(24) Paper tray right side cover
Open this to remove a paper misfeed in tray 1.
(25) Right side cover release lever
To remove a paper misfeed, pull and hold this lever up to
open the right side cover.
open the right side cover.
(13)
(14)
(15)
(18)
(17)
(16)
(21)
(20)
(24) (25)
(23)
(22)
(19)
Caution
The fusing unit is hot. Take care not to burn yourself
when removing a paper misfeed.
when removing a paper misfeed.
Do not touch or damage the transfer belt. This may
cause a defective image.
cause a defective image.
Your service technician will collect the waste toner
box.
box.
1-6
BEFORE USING THE MACHINE
Contents
AUTOMATIC DOCUMENT FEEDER AND DOCUMENT
GLASS
GLASS
Automatic document feeder
(1)
Paper feed roller
This roller rotates to automatically feed the original.
(2)
Document feeding area cover
Open this cover to remove an original misfeed or clean
the paper feed roller.
the paper feed roller.
(3)
Original guides
These help ensure that the original is scanned correctly.
Adjust the guides to the width of the original.
Adjust the guides to the width of the original.
☞
PLACING THE ORIGINAL
(page 1-35)
(4)
Document feeder tray
Place originals in this tray. 1-sided originals must be
placed face up.
placed face up.
☞
PLACING THE ORIGINAL
(page 1-35)
(5)
Original exit tray
Originals are delivered to this tray after scanning.
(6)
Scanning area
Originals placed in the document feeder tray are scanned
here.
here.
☞
REGULAR MAINTENANCE
(page 1-49)
(7)
Original size detector
This detects the size of an original placed on the
document glass.
document glass.
☞
PLACING THE ORIGINAL ON THE DOCUMENT
GLASS
GLASS
(page 1-37)
(8)
Document glass
Use this to scan a book or other thick original that cannot
be fed through the automatic document feeder.
be fed through the automatic document feeder.
☞
PLACING THE ORIGINAL ON THE DOCUMENT
GLASS
GLASS
(page 1-37)
(2)
(8)
(3)
(4)
(5)
(6)
(7)
(1)
1-7
BEFORE USING THE MACHINE
Contents
SIDE AND BACK
(1)
USB connector (A type)
Supports USB 2.0 (Hi-Speed).
This is used to connect a USB device such as USB
memory to the machine.
This is used to connect a USB device such as USB
memory to the machine.
(2)
USB connector (B type )
Supports USB 2.0 (Hi-Speed).
A computer can be connected to this connector to use
the machine as a printer.
For the USB cable, use a shielded cable.
A computer can be connected to this connector to use
the machine as a printer.
For the USB cable, use a shielded cable.
(3)
LAN connector
Connect the LAN cable to this connector when the
machine is used on a network.
For the LAN cable, use a shielded type cable.
machine is used on a network.
For the LAN cable, use a shielded type cable.
(4)
Service-only connector
(5)
Power plug
(6)
Extension phone socket
When the fax function of the machine is used, an
extension phone can be connected to this socket.
extension phone can be connected to this socket.
(7)
Telephone line socket
When the fax function of the machine is used, the
telephone line is connected to this socket.
telephone line is connected to this socket.
When the fax expansion kit is installed
(1)
(2)
(3)
(4)
(5)
Caution
This connector is for use only by service technicians.
Connecting a cable to this connector may cause the
machine to malfunction.
Connecting a cable to this connector may cause the
machine to malfunction.
Important note for service technicians:
The cable connected to the service connector must be
less than 3 m (118") in length.
The cable connected to the service connector must be
less than 3 m (118") in length.
(6)
(7)
Click on the first or last page to see other MX-2310U / MX-3111U (serv.man22) service manuals if exist.