Sharp MX-2310U / MX-3111U (serv.man16) Service Manual ▷ View online
MX-3610N ADJUSTMENTS AND SETTINGS 4 – 32
(2) Adjustment procedures
1) Set the SIT chart (UKOG-0280FCZZ or UKOG-0280FCZ1) to
1) Set the SIT chart (UKOG-0280FCZZ or UKOG-0280FCZ1) to
the reference position on the left rear frame side of the docu-
ment table.
Set the chart so that the lighter density side of the patch is on
the left side.
ment table.
Set the chart so that the lighter density side of the patch is on
the left side.
If the SIT chart is not available, execute SIM 63-5 to set the
CCD gamma to the default. In this case, however, the adjust-
ment accuracy is lower when compared with the adjustment
method using the SIT chart.
CCD gamma to the default. In this case, however, the adjust-
ment accuracy is lower when compared with the adjustment
method using the SIT chart.
Check to insure that the SIT chart (UKOG-0280FCZZ or
UKOG-0280FCZ1) is in close contact with the document table.
UKOG-0280FCZ1) is in close contact with the document table.
UKOG-0280FCZZ is equivalent to UKOG-0280FCZ1.
2) Enter the SIM 63-3 mode and press [EXECUTE] key.
The automatic operation is started. During the adjustment,
[EXECUTE] is highlighted. After completion of the adjustment,
[EXECUTE] returns to the normal display.
[EXECUTE] is highlighted. After completion of the adjustment,
[EXECUTE] returns to the normal display.
Since the SIT chart (UKOG-0280FCZZ or UKOG-0280FC Z1)
is easily discolored by sunlight (especially ultraviolet rays) and
humidity and temperature, put it in a bag (such as a dark file)
and store in a dark place of low temperature and low humidity.
is easily discolored by sunlight (especially ultraviolet rays) and
humidity and temperature, put it in a bag (such as a dark file)
and store in a dark place of low temperature and low humidity.
SET 1 Color balance adjustment target setup
a. General
When the automatic color balance adjustment is executed, a cer-
tain color balance (gamma) is used as the target.
There are following three kinds of the target.
• Factory color balance (gamma) target
• Service color balance (gamma) target
• User color balance (gamma) target
In the above three, only the service color balance target can be set
to a desired level.
This setting is required in the following cases.
* When the color balance and density adjustments are executed
When the automatic color balance adjustment is executed, a cer-
tain color balance (gamma) is used as the target.
There are following three kinds of the target.
• Factory color balance (gamma) target
• Service color balance (gamma) target
• User color balance (gamma) target
In the above three, only the service color balance target can be set
to a desired level.
This setting is required in the following cases.
* When the color balance and density adjustments are executed
manually (SIM46-21) (SIM67-25)
* U2 trouble has occurred.
* When the MFP PWB is replaced.
* When the EEPROM on the MFP PWB is replaced.
* The scanner control PWB has been replaced.
* The EEPROM on the scanner control PWB has been replaced.
* When the user requests for customizing the color balance.
* When the service color balance target gamma is judged as
* When the MFP PWB is replaced.
* When the EEPROM on the MFP PWB is replaced.
* The scanner control PWB has been replaced.
* The EEPROM on the scanner control PWB has been replaced.
* When the user requests for customizing the color balance.
* When the service color balance target gamma is judged as
improper.
SET 1A Copy color balance adjustment target setup
• Each color balance target for the copy color balance adjustment
ǂǂǂ6,08/$7,21ǂǂ12
&/26(
7(67
6&$11(5&2/25%$/$1&($872$'-8670(17
(;(&87(
6(77+(&+$5721'63)$1'728&+>(;(&87(@
(;(&87(
Type
Descriptions
A
Factory color
balance (gamma)
target
balance (gamma)
target
There are three kinds of the color balance target,
and each of them is specified according to the
machine design. Use SIM 63-11 to select one of
them as the factory target. The default setting
(factory setting) is the color balance (DEF1)
which emphasizes color reproduction.
and each of them is specified according to the
machine design. Use SIM 63-11 to select one of
them as the factory target. The default setting
(factory setting) is the color balance (DEF1)
which emphasizes color reproduction.
B
Service color
balance (gamma)
target
balance (gamma)
target
This target is used when the user requests to
customize the color balance to user's desired
level. In advance, the user's unique color
balance must be registered as the service color
balance target. The above registration (setting)
is made by the serviceman with SIM 46-21 to
adjust the color balance and with SIM 63-7 to
register it.
This color balance target is used when the user
executes the color balance adjustment. When,
therefore, the service color balance target is
changed, the color balance target of the user's
color balance adjustment is also changed.
When, however, SIM 63-8 is executed, the color
balance is set to the factory color balance target
set with SIM 63-11. The default setting (factory
setting) of the color balance is same as the
factory color balance target. (Emphasized on
color reproduction (DEF1))
If the user does not request for customizing the
color balance, be sure to use SIM 63-8 to set the
color balance to the factory color balance target.
customize the color balance to user's desired
level. In advance, the user's unique color
balance must be registered as the service color
balance target. The above registration (setting)
is made by the serviceman with SIM 46-21 to
adjust the color balance and with SIM 63-7 to
register it.
This color balance target is used when the user
executes the color balance adjustment. When,
therefore, the service color balance target is
changed, the color balance target of the user's
color balance adjustment is also changed.
When, however, SIM 63-8 is executed, the color
balance is set to the factory color balance target
set with SIM 63-11. The default setting (factory
setting) of the color balance is same as the
factory color balance target. (Emphasized on
color reproduction (DEF1))
If the user does not request for customizing the
color balance, be sure to use SIM 63-8 to set the
color balance to the factory color balance target.
C
User color
balance (gamma)
target
balance (gamma)
target
Same color balance as the service color balance
(gamma) target When the service color balance
target is changed, this color balance target is
also changed accordingly.
(gamma) target When the service color balance
target is changed, this color balance target is
also changed accordingly.
MX-3610N ADJUSTMENTS AND SETTINGS 4 – 33
• Relationship between the factory target and the service target and the color balance target for the user color balance adjustment in the copy
color balance adjustment (Automatic adjustment) (SIM 46-74/46-24)
• Factory target in the copy color balance adjustment (SIM 46-74/46-24)
By use of SIM 63-11, one of the following color balances can be set as the factory color balance target.
Each of the three color balances cannot be changed. (Fixed)
Each of the three color balances cannot be changed. (Fixed)
• Service color balance target in the copy color balance adjust-
ment ((Automatic adjustment) SIM 46-74/46-24).
For the service color balance target, an optional color balance
can be adjusted with SIM 46-21 and registered with SIM 63-7.
When, however, SIM 63-8 is executed, the color balance is set to
the same balance as the factory color balance target set with
SIM 63-11.
For the service color balance target, an optional color balance
can be adjusted with SIM 46-21 and registered with SIM 63-7.
When, however, SIM 63-8 is executed, the color balance is set to
the same balance as the factory color balance target set with
SIM 63-11.
• Color balance target in the user color balance adjustment
This color balance is same as the service color balance target in
the copy color balance adjustment (Automatic adjustment) (SIM
46-74/46-24). When, therefore, the service color balance target
is changed, this target is also changed accordingly.
the copy color balance adjustment (Automatic adjustment) (SIM
46-74/46-24). When, therefore, the service color balance target
is changed, this target is also changed accordingly.
(Meaning of the service color balance target gamma data and the
purpose of registration)
This procedure must be executed only when the color balance is
customized with SIM 46-21.
If the color balance is not customized, this procedure is not
required.
After completion of the customized color balance adjustment (Man-
ual) with SIM 46-21 according to the user's request, use SIM 63-7
to register the service color balance target data by using adjust-
ment pattern that was printed in this mode.
purpose of registration)
This procedure must be executed only when the color balance is
customized with SIM 46-21.
If the color balance is not customized, this procedure is not
required.
After completion of the customized color balance adjustment (Man-
ual) with SIM 46-21 according to the user's request, use SIM 63-7
to register the service color balance target data by using adjust-
ment pattern that was printed in this mode.
In this case, be sure to use A4 or 11" x 8.5" paper for printing the
adjustment pattern by SIM 46-21.
By this procedure, the service color balance target is revised.
adjustment pattern by SIM 46-21.
By this procedure, the service color balance target is revised.
Use SIM 63-11 to select one of the three
kinds of color balance targets.
kinds of color balance targets.
Factory color balance
target (DEF1)
target (DEF1)
Factory color balance
target (DEF2)
target (DEF2)
Factory color balance
target (DEF3)
target (DEF3)
Color balance target in the copy color balance
automatic adjustment (SIM 46-24)
automatic adjustment (SIM 46-24)
Factory color balance
target (one of DEF1 - 3)
target (one of DEF1 - 3)
Execute SIM 63-8.
(The service color balance target is the
same as the factory color balance target.)
(The service color balance target is the
same as the factory color balance target.)
Factory setting
Factory color balance
target (DEF1)
target (DEF1)
=
=
Color balance target in the user color balance adjustment
Color balance target for
the user color balance
adjustment
the user color balance
adjustment
Service color balance
target
target
Service color balance
target
target
Service color balance
target
target
Service color balance
target (Unique)
target (Unique)
=
Factory color balance
target
(one of DEF1 - 3)
target
(one of DEF1 - 3)
Use SIM 46-21 to adjust the optional color
balance, and use SIM 63-7 to register it.
balance, and use SIM 63-7 to register it.
DEF1
DEF1
Item
Content
Default
DEF2
DEF3
Factory color balance target (DEF3) =
Service color balance target/Color balance
target for the user color balance adjustment
Service color balance target/Color balance
target for the user color balance adjustment
The engine color balance adjustment target in the automatic color balance
operation is slightly shifted to Magenta. When this target is selected, the
color balance is converted into natural gray color balance by the color
correction table in an actual copy mode and print is made.
operation is slightly shifted to Magenta. When this target is selected, the
color balance is converted into natural gray color balance by the color
correction table in an actual copy mode and print is made.
The engine color balance adjustment target in the automatic color balance
operation is slightly shifted to natural gray color balance. When this target
is selected, the color balance is slightly shifted to Cyan by the color
correction table in an actual copy mode and print is made.
operation is slightly shifted to natural gray color balance. When this target
is selected, the color balance is slightly shifted to Cyan by the color
correction table in an actual copy mode and print is made.
The engine color balance adjustment target in the automatic color balance
operation is slightly shifted to Cyan. When this target is selected, the color
balance is converted into the color balance with enhanced Cyan by the
color correction table in an actual copy mode and print is made.
operation is slightly shifted to Cyan. When this target is selected, the color
balance is converted into the color balance with enhanced Cyan by the
color correction table in an actual copy mode and print is made.
SIM63-8
SIM63-8
SIM63-8
Factory color balance target (DEF2) =
Service color balance target/Color balance
target for the user color balance adjustment
Service color balance target/Color balance
target for the user color balance adjustment
Factory color balance target
(DEF1) = Service color balance
target/Color balance target for the
user color balance adjustment
(DEF1) = Service color balance
target/Color balance target for the
user color balance adjustment
Hue
+b* Direction of Yellow
Direction of Blue
(A)
Factory color balance target
(DEF2)
(DEF2)
Factory color balance target
(DEF1)
(DEF1)
Direction
of Red
of Red
Factory color balance target
(DEF3)
(DEF3)
Direction
of Green
of Green
MX-3610N ADJUSTMENTS AND SETTINGS 4 – 34
It is recommended to keep the printed adjustment pattern created
with SIM 46-21. This adjustment pattern can be used to register the
same color balance target to another machine.
It is also useful to register the service color balance target data.
Do not fold it and keep it under the circumstances which protect it
from discoloration and dirt.
The service color balance target data is registered immediately
after the color balance adjustment (Manual) with SIM 46-21.
If a considerable time has passed after completion of the color bal-
ance adjustment (Manual) with SIM 46-21, the color balance of the
adjustment pattern at the time of adjustment differs from the color
balance of the adjustment pattern printed after a considerable time.
Never use such a pattern for the adjustment.
The accuracy of the service color balance target data can be
judges as follows.
When result of the color valance adjustment (Auto) with selecting
the service color balance target in SIM 46-74/46-24 is unsatisfac-
tory or abnormal.
In that case, the registered service target data for the color balance
adjustment (Auto) may be improper.
This may be caused when an improper or abnormal color balance
adjustment pattern was used to register the service color balance
target data for the color balance adjustment with SIM 63-7.
The color balance adjustment pattern used in registration was
made and printed by the color balance adjustment (Manual) with
SIM 46-21. This procedure may have been executed erroneously
with SIM 46-21. This adjustment pattern can be used to register the
same color balance target to another machine.
It is also useful to register the service color balance target data.
Do not fold it and keep it under the circumstances which protect it
from discoloration and dirt.
The service color balance target data is registered immediately
after the color balance adjustment (Manual) with SIM 46-21.
If a considerable time has passed after completion of the color bal-
ance adjustment (Manual) with SIM 46-21, the color balance of the
adjustment pattern at the time of adjustment differs from the color
balance of the adjustment pattern printed after a considerable time.
Never use such a pattern for the adjustment.
The accuracy of the service color balance target data can be
judges as follows.
When result of the color valance adjustment (Auto) with selecting
the service color balance target in SIM 46-74/46-24 is unsatisfac-
tory or abnormal.
In that case, the registered service target data for the color balance
adjustment (Auto) may be improper.
This may be caused when an improper or abnormal color balance
adjustment pattern was used to register the service color balance
target data for the color balance adjustment with SIM 63-7.
The color balance adjustment pattern used in registration was
made and printed by the color balance adjustment (Manual) with
SIM 46-21. This procedure may have been executed erroneously
a. Setting procedure
(Setting procedure of an optional color balance (gamma) as the
service color balance target)
1) Use SIM 46-21 (Copy color balance adjustment (manual
(Setting procedure of an optional color balance (gamma) as the
service color balance target)
1) Use SIM 46-21 (Copy color balance adjustment (manual
adjustment) mode) to print two sheets of the color patch image
(adjustment pattern).
(adjustment pattern).
In this case, be sure to use A4 or 11" x 8.5" paper for printing
the adjustment pattern by SIM 46-21.
the adjustment pattern by SIM 46-21.
If the color balance is shifted from the standard, an adjustment
is required. If not, an adjustment is not required. When an
optional color balance is requested by the user, make an
adjustment.
is required. If not, an adjustment is not required. When an
optional color balance is requested by the user, make an
adjustment.
2) Enter the SIM 63-7 mode.
3) Press [SETUP] key.
4) Set the color patch image (adjustment pattern) correctly
4) Set the color patch image (adjustment pattern) correctly
adjusted and printed in the copy color balance adjustment
(Manual adjustment) (SIM 46-21) (ADJ 10C (2)) on the docu-
ment table.
The color patch image (adjustment pattern) printed with SIM
64-7 can be used instead. In this case, however, check that the
printed pattern is normal.
(When the color patch image (adjustment pattern) is printed by
SIM 64-7, set the item B (PROC ADJ) to "0 (YES)" and press
[EXECUTE] key to print.)
(Manual adjustment) (SIM 46-21) (ADJ 10C (2)) on the docu-
ment table.
The color patch image (adjustment pattern) printed with SIM
64-7 can be used instead. In this case, however, check that the
printed pattern is normal.
(When the color patch image (adjustment pattern) is printed by
SIM 64-7, set the item B (PROC ADJ) to "0 (YES)" and press
[EXECUTE] key to print.)
A color patch image (adjustment pattern) printed by another
machine can be used.
Set the pattern so that the light density side is on the left side.
Place 5 sheets of white paper on the color patch image
(adjustment pattern).
If the color balance could not be adjusted satisfactorily with
SIM 46-21 (Color balance adjustment (Manual)), do not exe-
cute SIM 63-7 to register the service color balance target data.
machine can be used.
Set the pattern so that the light density side is on the left side.
Place 5 sheets of white paper on the color patch image
(adjustment pattern).
If the color balance could not be adjusted satisfactorily with
SIM 46-21 (Color balance adjustment (Manual)), do not exe-
cute SIM 63-7 to register the service color balance target data.
5)
Press [EXECUTE] key.
The color patch image (adjustment pattern) is read.
6)
Press [REPEAT] key, set the second color patch image
(adjustment pattern), and execute the procedure 5) again.
(adjustment pattern), and execute the procedure 5) again.
The color balance (gamma) target set level of each color
(KCMY) can be checked with K/C/M/Y keys.
Check that the set level is increased in the sequence of B - Q
(MAX). If there is no variation or variation is reversed, it is
judged as abnormal.
In case of an abnormality, repair the problem and try again.
(KCMY) can be checked with K/C/M/Y keys.
Check that the set level is increased in the sequence of B - Q
(MAX). If there is no variation or variation is reversed, it is
judged as abnormal.
In case of an abnormality, repair the problem and try again.
7)
Press [OK] key.
The color balance (gamma) of the color patch image (adjust-
ment pattern) used in the procedure 5) is set as the service tar-
get.
The color balance (gamma) of the color patch image (adjust-
ment pattern) used in the procedure 5) is set as the service tar-
get.
(Procedures to set the service color balance target and the
color balance target for the user color balance adjustment to
the same color balance as the factory color balance target)
color balance target for the user color balance adjustment to
the same color balance as the factory color balance target)
This procedure must not be executed when the copy color balance
was adjusted with SIM 46-21 to a unique color balance requested
by the user and it was registered as the service color balance tar-
get with SIM 63-7.
When the factory color balance target is changed with SIM 63-11,
be sure to execute this procedure.
was adjusted with SIM 46-21 to a unique color balance requested
by the user and it was registered as the service color balance tar-
get with SIM 63-7.
When the factory color balance target is changed with SIM 63-11,
be sure to execute this procedure.
ǂǂǂ6,08/$7,21ǂǂ12
&/26(
7(67
6&$11(57$5*(72)&2/25&$/,%6(7836(59,&(
6(783
%&'()
*+,-.
㩺㪣012
.
&
0
<
ǂǂǂ6,08/$7,21ǂǂ12
&/26(
7(67
6&$11(57$5*(72)&2/25&$/,%6(7836(59,&(
(;(&87(
6(77+(&+$57213/$7(1$1'728&+>(;(&87(@
ǂǂǂ6,08/$7,21ǂǂ12
&/26(
7(67
6&$11(57$5*(72)&2/25&$/,%6(7836(59,&(
(;(&87(
12:&+$573$7&+5($',1*
MX-3610N ADJUSTMENTS AND SETTINGS 4 – 35
1) Enter the SIM 63-8 mode.
2)
Press [EXECUTE] key.
3)
Press [YES] key.
The service color balance target and the color balance target for
the user color balance adjustment are set to the same color bal-
ance as the factory color balance target.
the user color balance adjustment are set to the same color bal-
ance as the factory color balance target.
SET 1B Printer color balance adjustment target setup
• Color balance target for the printer color balance adjustment
• Relationship between the factory target and the service target and the color balance target for the user color balance adjustment in the
printer color balance adjustment (Automatic adjustment) (SIM 46-74/76-24)
ǂǂǂ6,08/$7,21ǂǂ12
&/26(
7(67
67$1'$5'6&$11(57$5*(76(77,1*6(59,&(
(;(&87(
$5(<28685("
<(6
12
Type
Descriptions
A
Factory color
balance (gamma)
target
balance (gamma)
target
There are three kinds of the color balance targets, and each of them is specified according to the machine design. Use SIM 67-26 to
select one of them as the factory target. The default setting (factory setting) is the color balance (DEF1) which emphasizes color
reproduction.
select one of them as the factory target. The default setting (factory setting) is the color balance (DEF1) which emphasizes color
reproduction.
B
Service color
balance (gamma)
target
balance (gamma)
target
This target is used when the user requests to customize the color balance to user's desired level. In advance, the user's unique color
balance must be registered as the service color balance target. The above registration (setting) is made by the serviceman with SIM
67-25 to adjust the color balance and with SIM 67-27 to register it.
This color balance target is used when the user executes the color balance adjustment. When, therefore, the service color balance
target is changed, the color balance target of the user's color balance adjustment is also changed. When, however, SIM 67-28 is
executed, the color balance is set to the factory color balance target set with SIM 67-26. The default setting (factory setting) of the color
balance is same as the factory color balance target. (Emphasized on color reproduction (DEF1))
If the user does not request for customizing the color balance, be sure to use SIM 67-28 to set the color balance to the factory color
balance target.
balance must be registered as the service color balance target. The above registration (setting) is made by the serviceman with SIM
67-25 to adjust the color balance and with SIM 67-27 to register it.
This color balance target is used when the user executes the color balance adjustment. When, therefore, the service color balance
target is changed, the color balance target of the user's color balance adjustment is also changed. When, however, SIM 67-28 is
executed, the color balance is set to the factory color balance target set with SIM 67-26. The default setting (factory setting) of the color
balance is same as the factory color balance target. (Emphasized on color reproduction (DEF1))
If the user does not request for customizing the color balance, be sure to use SIM 67-28 to set the color balance to the factory color
balance target.
C
User color balance
(gamma) target
(gamma) target
Same color balance as the service color balance (gamma) target When the service color balance target is changed, this color balance
target is also changed accordingly.
target is also changed accordingly.
Use SIM 67-26 to select one of the three
kinds of color balance targets.
kinds of color balance targets.
Factory color balance
target (DEF1)
target (DEF1)
Factory color balance
target (DEF2)
target (DEF2)
Factory color balance
target (DEF3)
target (DEF3)
Color balance target in the printer color balance
automatic adjustment (SIM 67-24)
automatic adjustment (SIM 67-24)
Factory color balance
target (one of DEF1 - 3)
target (one of DEF1 - 3)
Execute SIM 67-28.
(The service color balance target is
the same as the factory color balance
target.)
(The service color balance target is
the same as the factory color balance
target.)
Factory setting
Factory color balance
target (DEF1)
target (DEF1)
=
=
Color balance target in the user color balance adjustment
Color balance target for
the user color balance
adjustment
the user color balance
adjustment
Service color balance
target
target
Service color balance
target
target
Service color balance
target
target
Service color balance
target (Unique)
target (Unique)
=
Factory color balance
target (one of DEF1 - 3)
target (one of DEF1 - 3)
Use SIM 67-25 to adjust the optional color
balance, and use SIM 67-27 to register it.
balance, and use SIM 67-27 to register it.
Click on the first or last page to see other MX-2310U / MX-3111U (serv.man16) service manuals if exist.