DOWNLOAD Sharp MX-2300N / MX-2700N / MX-2300G / MX-2700G / MX-2300FG / MX-2700FG (serv.man28) Service Manual ↓ Size: 1.35 MB | Pages: 28 in PDF or view online for FREE

Wave length

785 nm

+10 nm
-15 nm

Pulse times

North America:

23 cpm model: (5.1 µs ±5.1 ns)/7 mm
27 cpm model: (5.1 µs ±5.1 ns)/7 mm

Europe: 

23 cpm model: (5.1 µs ±5.1 ns)/7 mm
27 cpm model: (5.1 µs ±5.1 ns)/7 mm

Output power

Max 0.7 mW

At the production line, the output power of the scanner unit is adjusted to 0.233 MILLIWATT PLUS 5% and is maintained constant by 
the operation of the Automatic Power Control (APC).

Caution
Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation 
exposure.

For North America:

This Digital Equipment is rated Class 1 and complies with 21 CFR 1040.10 and 1040.11 of the CDRH standards. This means that 
the equipment does not produce hazardous laser radiation. For your safety, observe the precautions below.

• Do not remove the cabinet, operation panel or any other covers.
• The equipment's exterior covers contain several safety interlock switches. Do not bypass any safety interlock by inserting wedges 

or other items into switch slots.

For Europe:

CLASS 1 LASER PRODUCT

LASER KLASSE 1

LUOKAN 1 LASERLAITE

KLASS 1 LASERAPPARAT

CLASS 3B INVISIBLE LASER 
RADIATION WHEN OPEN AND 
 INTERLOCKS DEFEATED. 
AVOID EXPOSURE TO BEAM.

UNSICHTBARE 
LASERSTRAHLUNG  DER 
KLASSE 3B, WENN 
ABDECKUNG GEÖFFNET UND 
SICHERHEITSVERRIEGELUNG 
ÜBERBRÜCKT. NICHT DEM 
STRAHL AUSSETZEN.

USYNLIG LASERSTRÅLNING 
AF KLASSE 3B VED ÅBNING, 
NÅR SIKKERHEDSBRYDERE 
ER UDE AF FUNKTION. UNDGÅ 
UDSÆTTELSE FOR 
STRÅLNING.

USYNLIG KLASSE 3B 
LASERSTRÅLNING NÅR 
DEKSEL ÅPNES OG  
SIKKERHEDSLÅS BRYTES . 
UNNGÅ EKSPONERING FOR 
STRÅLEN.

OSYNLIG LASERSTRÅLNING 
KLASS 3B NÄR DENNA DEL ÄR 
ÖPPNAD OCH SPÄRRAR ÄR 
URKOPPLADE. UNDVIK 
EXPONERING FÖR STRÅLEN.

AVATTAESSA JA 
SUOJALUKITUS OHITETTAESSA 
OLET ALTTIINA NÄKYMÄTÖNTÄ 
LUOKAN 3B LASERSÄTEILYLLE. 
ÄLÄ KATSO SÄTEESEEN.

The above label is affixed to the laser 
unit inside the machine.

mx2700_gb_saf.fm  3 ページ  ２００５年１１月１日　火曜日　午後４時５１分

Improper installation may damage this product. Please note the following during initial installation and whenever the 
machine is moved.

1. The machine should be installed near an accessible 

power outlet for easy connection.

2. Be sure to connect the power cord only to a power 

outlet that meets the specified voltage and current 
requirements. Also make certain the outlet is properly 
grounded.

• For the power supply requirements, see the name 

plate at the bottom of the back of the left side of the 
machine.

Connect the machine to a power outlet which is not 
used for other electric appliances. If a lighting fixture is
connected to the same outlet, the light may flicker.

3. Do not install the machine in areas that are:

• damp, humid, or very dusty 
• exposed to direct sunlight 
• poorly ventilated 
• subject to extreme temperature or humidity 

changes, e.g., near an air conditioner or heater.

4. Be sure to allow the required space around the 

machine for servicing and proper ventilation.

5. When moving the machine, four persons must firmly 

grasp the transport handles on both sides of the 
machine.

6. The machine includes a built-in hard drive. Do not 

subject the machine to shock or vibration. In 
particular, never move the machine while the power is 
on.

45 cm
(17-23/32")

30 cm
(11-13/16")

30 cm
(11-13/16")

A small amount of ozone is produced within the printer during operation. The emission level is insufficient to cause any health 
hazard.

NOTE:
The present recommended long term exposure limit for ozone is 0.1 ppm (0.2 mg/m

3

) calculated as an 8 hr. time-weighted average 

concentration.
However, since the small amount that is emitted may have an objectionable odor, it is advisable to place the copier in a ventilated 
area.

mx2700_gb_saf.fm  4 ページ  ２００５年１１月１日　火曜日　午後４時５１分

Standard supplies for this product that can replaced by the user include paper, toner cartridges, and staple cartridges for 
the finisher.
Be sure to use only SHARP-specified products for the toner cartridges, finisher staple cartridge, saddle stitch finisher 
staple cartridge, and transparency film.

Proper storage
1. Store the supplies in a location that is:

• clean and dry,
• at a stable temperature,
• not exposed to direct sunlight.

2. Store paper in the wrapper and lying flat.
3. Paper stored in packages standing up or out of the wrapper may curl or become damp, resulting in paper misfeeds.

Storing toner cartridges
Store a new toner cartridge box horizontally. Do not store it standing on end. If stored standing on end, the toner may not 
distribute well even after shaking the cartridge vigorously, and will remain inside the cartridge without flowing out.

Staple cartridge
The finisher and saddle stitch finisher require the following staple cartridge:

MX-SCX1
Staple cartridge for finisher (approx. 5000 per cartridge x 3 cartridges)

AR-SC2
Staple cartridge for saddle stitch finisher (approx. 5000 per cartridge x 3 cartridges)

The supply of spare parts for repair of the machine is guaranteed for at least 7 years following the termination of 
production. Spare parts are those parts of the machine which may break down within the scope of the ordinary use of 
the product whereas those parts which normally exceed the life of the product are not to be considered as spare parts. 
Consumables too, are available for 7 years following the termination of production.

For best copying results, be sure to use only Sharp Genuine Supplies which are designed, 
engineered, and tested to maximize the life and performance of Sharp products. Look for the 
Genuine Supplies label on the toner package.

mx2700_gb_saf.fm  5 ページ  ２００５年１１月１日　火曜日　午後４時５１分

* First copy out time is measured with original on the document glass in full ready condition with fuser at operating temperature and 

mirror motor at operating speed, actual time may vary based on environment conditions.

Digital Full Colour Multifunctional System MX-2300N/MX-2700N

Desktop

OPC drum

Electrophotographic system (laser)

Dry-type two-component magnetic brush development

Heat rollers

Colour copy time: 8.9 seconds   Black and white copy time: 6.3 seconds
(Portrait feeding of A4 (8-1/2" x 11") sheets from 1st paper tray, without auto colour selection and 
auto colour mode.)

Document glass

Black and white scanning: 600 x 600 dpi, 600 x 300 dpi (factory 

default values)

Colour scanning: 600 x 600 dpi (factory default values)

Reversing single pass 
feeder (automatic 
document feeder)

Black and white scanning: 600 x 600 dpi, 600 x 300 dpi (factory 

default values)

Colour scanning: 600 x 600 dpi (factory default values)

600 x 600 dpi

10 bits

Black and white printing: 2 tones (1 bit)
Colour printing: 2 tones per colour (1 bit) or 16 tones per colour (4 bits)

Max. A3 (11" x 17") / sheets, bound documents

Maximum: A3 (11" x 17") Minimum: A5R (5-1/4" x 5-3/4")

Leading edge: 4 mm (11/64") or less, trailing edge: 3 mm (1/8") or less, near edge / far edge: total 
4 mm (11/64") or less

80 seconds or less

Variable: 25% to 400% in increments of 1%, total 376 increments (25% to 200% when the auto 

document feeder is used)

Fixed presets: 25%, 50%, 70%, 81%, 86%, 100%, 115%, 122%, 141%, 200% and 400% for AB sizes; 

25%, 50%, 64%, 77%, 100%, 121%, 129%, 200% and 400% for inch sizes.

Two reduction ratios and two enlargement ratios can be stored.

Paper sizes:

A3, B4, A4, A4R, B5, B5R, A5R, 11" x 17", 8-1/2" x 14", 8-1/2" x 13", 8-1/2" x 11", 
8-1/2" x 11"R, 7-1/4" x 10-1/2"R, 5-1/2" x 8-1/2"R, 8K, 16K, 16KR

Paper weight:

Plain paper (60 g/m

2

 to 105 g/m

2

 (16 lbs. to 28 lbs.))

Paper capacity: 500 sheets (80 g/m

2

 (21 lbs.))

Paper types:

SHARP-recommended plain paper, recycled paper, and coloured paper

Paper sizes:

A3, B4, A4, A4R, B5, B5R, A5R, 11" x 17", 8-1/2" x 14", 8-1/2" x 13", 8-1/2" x 11", 
8-1/2" x 11"R, 7-1/4" x 10-1/2"R, 5-1/2" x 8-1/2"R, 8K, 16K, 16KR

Paper weight:

Plain paper (60 g/m

2

 to 105 g/m

2

 (16 lbs. to 28 lbs.))

Paper capacity: 500 sheets (80 g/m

2

 (21 lbs.))

Paper types:

SHARP-recommended plain paper, recycled paper, and coloured paper

mx2700_gb_saf.fm  6 ページ  ２００５年１１月２日　水曜日　午前９時２１分