Sharp DM-2000 Handy Guide ▷ View online
Machine Installation
Version 2.1
Issue 05/2000
6
SHARP ELECTRONICS (UK) LTD
COPIER TECHNICAL SUPPORT
TECHNICAL SERVICES GROUP
MACHINE
OPTIONS
INSTALLATION ORDER
DM-FX1 Fax Board
AR-NC3D Network Card
AR-SP2 Document Feeder
AR-EB3 Electronic Sort Board
DEVELOPER SETUP
The toner/developer cartridge is self-
setting.
No set-up procedure is required.
setting.
No set-up procedure is required.
LASER PRINT
HORIZONTAL IMAGE CHECK
Sim 64 – 01 Laser print check
LASER PRINT
&
ORIGINAL OFF CENTER
Sim 50 – 10 Adjust All Cassettes
(Laser Print)
Sim 50 – 13 OC off centre adjust
Sim 50 – 16 SPF off centre adjust
Sim 50 – 18 Duplex print adjust
Sim 50 – 19 Duplex rear edge adjust
Sim 50 – 16 SPF off centre adjust
Sim 50 – 18 Duplex print adjust
Sim 50 – 19 Duplex rear edge adjust
Cont’d
Machine Installation
Version 2.1
Issue 05/2000
7
SHARP ELECTRONICS (UK) LTD
COPIER TECHNICAL SUPPORT
TECHNICAL SERVICES GROUP
COPY IMAGE POSITION
& VOID
Sim 50 – 01 Copy lead and trail edge
adjust ( all cassettes )
COPY QUALITY
Sim 46 – 01 Adjust Copy Density
( All Modes)
CASSETTE SIZES
Set cassette sizes as per Service
Manual page 5-3
Manual page 5-3
OTHER
Sim 21 – 01 Maintenance Cycle
Setting
Sim 26 – 06 Destination Setting
Sim 26 – 22 Destination Language
Sim 26 – 22 Destination Language
Setting
CUSTOM SETTINGS
(Key Operator)
Auto Power Off Setting
Pre-Heat Timer Setting
Auto clear time
Rotation copy
Pre-Heat Timer Setting
Auto clear time
Rotation copy
Routine Maintenance
Version 2.1
Issue 05/2000
8
SHARP ELECTRONICS (UK) LTD
COPIER TECHNICAL SUPPORT
TECHNICAL SERVICES GROUP
Although traditional routine maintenance is not required with these models,( replace upper
fuser roller @150k), the following items may require attention when making a routine visit
or at the one maintenance call (150k)
fuser roller @150k), the following items may require attention when making a routine visit
or at the one maintenance call (150k)
MAINTENANCE COMPLETED
Sim 20 – 01 Maintenance Counter Reset
Sim 21 – 01 Maintenance Setting Check
Sim 21 – 01 Maintenance Setting Check
DRUM REPLACEMENT
Sim 24 – 07 Drum Membrane Counter Reset
(normally resets when new drum cartridge is installed)
(normally resets when new drum cartridge is installed)
COPY QUALITY
Sim 46 – 01 Copier Mode Adjust
JAM & TROUBLE COUNTER
Sim 24 – 01 Jam memory, Jam counter clear
Sim 24 – 02 Trouble memory clear
Sim 24 – 02 Trouble memory clear
FEED ROLLER REPLACEMENT
Sim 24 – 06 Paper Feed Counter Reset
Machine Settings & Adjustments
Version 2.1
Issue 05/2000
9
SHARP ELECTRONICS (UK) LTD
COPIER TECHNICAL SUPPORT
TECHNICAL SERVICES GROUP
Section
Adjustment Item
Adjustment
Procedure
Process
1 Developer doctor gap
2 MG roller main pole position
2 MG roller main pole position
Laser scanner
1 Horizontal image distortion
LSU lever adjustment
2 Print off centre
Sim 50-10
Scanner
1 Vertical image distortion
balance
Copy lamp unit
installing position
installing position
2 Vertical image distortion
balance
No2/3 mirror base
installing position
installing position
3 Vertical image distortion
Winding pulley
position
position
4 Horizontal image distortion
F rail height adjust
5 Main scan magnification
ratio
CCD unit position
6 Main scan magnification
ratio
Sim 48-1
7 Original off centre
Sim 50-10
OC Detection
1
1
Detection position adjust
207 – 302mm
Original sensor
1 Size sensor adjust
(
not AR161
)
Sim 41 - 3
Copy Density
1 Copy mode
Sim 46
Paper Trans
1 Resist Roller Buckle
Sim 51-2
Click on the first or last page to see other DM-2000 service manuals if exist.