DOWNLOAD Sharp DM-2000 (serv.man6) Service Manual ↓ Size: 208.81 KB | Pages: 14 in PDF or view online for FREE

Model
DM-2000 (serv.man6)
Pages
14
Size
208.81 KB
Type
PDF
Document
Service Manual
Brand
Device
Copying Equipment / DM2000 Service Manual-Simulations Flash Rom Version Up Procedure
File
dm-2000-sm6.pdf
Date

Sharp DM-2000 (serv.man6) Service Manual ▷ View online

9) Select the data for MCU to be transferred.
automatically canceled. Go to procedure 11).
11) After transfer of data, turn off the machine and disconnect the con-
nector.
Reference: If the power is turned off during the procedure or in case
of a communication error, resume the procedure from 2).
2. PRINTER CONTROL PWB FIRMWARE
VERSION UP
A. Cases where flash memory rewriting is required
B. Necessary tools
1) Computer (PC) <Operates on MS-DOS.>
2) Parallel cable
3) Program data file (xxx.BIN)
C. Procedure
1) Print the configuration list to check the firmware version.
Use the operation panel of the copier to perform the following pro-
cedure.
ONLINE <off line> 
→ MENU <Test Printing Menu> → ITEM
<Configuration Page> 
→ ENTER <The test page prints>
2) Connect the PC and the copier with the parallel cable.
3) Turn on the power
4) Execute SIM 67-14.
“Erase Flash Data?” is displayed on the LCD.
5) Press the ENTER key on the copier’s operation panel.
“Now Erasing” is displayed on the LCD.
6) After deletion of data, “Please Send Data” is displayed on the LCD
and the machine enters the ready state for data input.
7) Download the program file.
(Note) Never turn off the power during download.
Set the PC to DOS mode 
→ Check that the display shows
READY. 
→ Then type COPY   /B   xxx.BIN  LPT1:
and press the enter key.
(  
space)
8) The machine enters the data reception mode.
9) When data reception and data writing into the flash ROM are
completed, the SUM check is automatically performed.
(Note) In case of an error, “Sum check Error” is displayed.
Turn off the power once, and repeat the procedures from 3).
10) If there is no problem on the result of the SUM check, “Complete”
is displayed on the LCD.
11) Turn off/on the power to print the configuration page with the
above procedures, and check the firmware version.
12) Perform printing on the PC side and check that printing is per-
formed normally.
DM-2000
8  –  2
9) Select the data for MCU to be transferred.
automatically canceled. Go to procedure 11).
11) After transfer of data, turn off the machine and disconnect the con-
nector.
Reference: If the power is turned off during the procedure or in case
of a communication error, resume the procedure from 2).
2. PRINTER CONTROL PWB FIRMWARE
VERSION UP
A. Cases where flash memory rewriting is required
B. Necessary tools
1) Computer (PC) <Operates on MS-DOS.>
2) Parallel cable
3) Program data file (xxx.BIN)
C. Procedure
1) Print the configuration list to check the firmware version.
Use the operation panel of the copier to perform the following pro-
cedure.
ONLINE <off line> 
→ MENU <Test Printing Menu> → ITEM
<Configuration Page> 
→ ENTER <The test page prints>
2) Connect the PC and the copier with the parallel cable.
3) Turn on the power
4) Execute SIM 67-14.
“Erase Flash Data?” is displayed on the LCD.
5) Press the ENTER key on the copier’s operation panel.
“Now Erasing” is displayed on the LCD.
6) After deletion of data, “Please Send Data” is displayed on the LCD
and the machine enters the ready state for data input.
7) Download the program file.
(Note) Never turn off the power during download.
Set the PC to DOS mode 
→ Check that the display shows
READY. 
→ Then type COPY   /B   xxx.BIN  LPT1:
and press the enter key.
(  
space)
8) The machine enters the data reception mode.
9) When data reception and data writing into the flash ROM are
completed, the SUM check is automatically performed.
(Note) In case of an error, “Sum check Error” is displayed.
Turn off the power once, and repeat the procedures from 3).
10) If there is no problem on the result of the SUM check, “Complete”
is displayed on the LCD.
11) Turn off/on the power to print the configuration page with the
above procedures, and check the firmware version.
12) Perform printing on the PC side and check that printing is per-
formed normally.
DM-2000
8  –  2
9) Select the data for MCU to be transferred.
automatically canceled. Go to procedure 11).
11) After transfer of data, turn off the machine and disconnect the con-
nector.
Reference: If the power is turned off during the procedure or in case
of a communication error, resume the procedure from 2).
2. PRINTER CONTROL PWB FIRMWARE
VERSION UP
A. Cases where flash memory rewriting is required
B. Necessary tools
1) Computer (PC) <Operates on MS-DOS.>
2) Parallel cable
3) Program data file (xxx.BIN)
C. Procedure
1) Print the configuration list to check the firmware version.
Use the operation panel of the copier to perform the following pro-
cedure.
ONLINE <off line> 
→ MENU <Test Printing Menu> → ITEM
<Configuration Page> 
→ ENTER <The test page prints>
2) Connect the PC and the copier with the parallel cable.
3) Turn on the power
4) Execute SIM 67-14.
“Erase Flash Data?” is displayed on the LCD.
5) Press the ENTER key on the copier’s operation panel.
“Now Erasing” is displayed on the LCD.
6) After deletion of data, “Please Send Data” is displayed on the LCD
and the machine enters the ready state for data input.
7) Download the program file.
(Note) Never turn off the power during download.
Set the PC to DOS mode 
→ Check that the display shows
READY. 
→ Then type COPY   /B   xxx.BIN  LPT1:
and press the enter key.
(  
space)
8) The machine enters the data reception mode.
9) When data reception and data writing into the flash ROM are
completed, the SUM check is automatically performed.
(Note) In case of an error, “Sum check Error” is displayed.
Turn off the power once, and repeat the procedures from 3).
10) If there is no problem on the result of the SUM check, “Complete”
is displayed on the LCD.
11) Turn off/on the power to print the configuration page with the
above procedures, and check the firmware version.
12) Perform printing on the PC side and check that printing is per-
formed normally.
DM-2000
8  –  2
9) Select the data for MCU to be transferred.
automatically canceled. Go to procedure 11).
11) After transfer of data, turn off the machine and disconnect the con-
nector.
Reference: If the power is turned off during the procedure or in case
of a communication error, resume the procedure from 2).
2. PRINTER CONTROL PWB FIRMWARE
VERSION UP
A. Cases where flash memory rewriting is required
B. Necessary tools
1) Computer (PC) <Operates on MS-DOS.>
2) Parallel cable
3) Program data file (xxx.BIN)
C. Procedure
1) Print the configuration list to check the firmware version.
Use the operation panel of the copier to perform the following pro-
cedure.
ONLINE <off line> 
→ MENU <Test Printing Menu> → ITEM
<Configuration Page> 
→ ENTER <The test page prints>
2) Connect the PC and the copier with the parallel cable.
3) Turn on the power
4) Execute SIM 67-14.
“Erase Flash Data?” is displayed on the LCD.
5) Press the ENTER key on the copier’s operation panel.
“Now Erasing” is displayed on the LCD.
6) After deletion of data, “Please Send Data” is displayed on the LCD
and the machine enters the ready state for data input.
7) Download the program file.
(Note) Never turn off the power during download.
Set the PC to DOS mode 
→ Check that the display shows
READY. 
→ Then type COPY   /B   xxx.BIN  LPT1:
and press the enter key.
(  
space)
8) The machine enters the data reception mode.
9) When data reception and data writing into the flash ROM are
completed, the SUM check is automatically performed.
(Note) In case of an error, “Sum check Error” is displayed.
Turn off the power once, and repeat the procedures from 3).
10) If there is no problem on the result of the SUM check, “Complete”
is displayed on the LCD.
11) Turn off/on the power to print the configuration page with the
above procedures, and check the firmware version.
12) Perform printing on the PC side and check that printing is per-
formed normally.
DM-2000
8  –  2
Page of 14
Display

Sharp DM-2000 (serv.man6) Service Manual ▷ Download