DOWNLOAD Sharp DM-2000 (serv.man5) Service Manual ↓ Size: 669.84 KB | Pages: 16 in PDF or view online for FREE

Model
DM-2000 (serv.man5)
Pages
16
Size
669.84 KB
Type
PDF
Document
Service Manual
Brand
Device
Copying Equipment / DM2000 Service Manual-Unpacking Installation Adjustments
File
dm-2000-sm5.pdf
Date
PREV: Sharp DM-2000 (serv.man4) Service Manual

Sharp DM-2000 (serv.man5) Service Manual ▷ View online

<Adjustment specification>
Mode
Specification
SIM
Set value
Set range
Original off
center mode
(OC mode)
Single:
Center 
±
2.0 mm
SIM
50-13
Add 1:
0.1 mm shift
to R side
Reduce 1:
0.1 mm shift
to L side
1 
∼ 99
Duplex:
Center 
±2.5
mm
b. SPF mode
Note:
● Before performing this adjustment, be sure to check that the
paper off center is properly adjusted.
1) Make a test chart for the center position adjustment and set it on
the SPF.
<Adjustment specification>
Draw a line on a paper in the scanning direction.
2) Make a normal copy from the manual paper feed tray, and com-
pare the copy and the original test chart.
If necessary, perform the following adjustment procedures.
3) Execute SIM 50-16.
4) After warmup, shading is performed and the current set value of
the off center adjustment at each paper feed port is displayed on
the display section in 2 digits.
5) Enter the set value and press the start key.
<Adjustment specification>
Mode
Specification
SIM
Set value
Set range
Original off
center mode
(SPF mode)
Single:
Center 
±
3.0 mm
SIM
50-16
Add 1:
0.1 mm shift
to R side
Reduce 1:
0.1 mm shift
to L side
1 
∼ 99
Duplex:
Center 
±3.5
mm
(8) OC (SPF) open/close detection position adjustment
1) Set A4 or 8 1/2" 
× 11" paper on the OC table.
Check that the document size display on the operation panel in-
dicates the correct size of the set paper.
2) Close the OC (SPF) with a small clearance for insertion of your
hand left, and remove the paper from the OC table.
The document size display does not change from the display in 1).
3) Open the OC (SPF) slowly until the display on the operation panel
changes (all the document size display lamps are turned off), and
measure dimension A shown below under that state.
<Spec value>
OC (SPF) open/close position A: 207 
∼ 302mm
4) If the OC (SPF) open/close position A is not 207 
∼ 302mm, adjust
the open/close sensor mounting plate position as shown below.
(9) Original sensor adjustment (SIM 43-3)
1) Execute SIM 41-2.
2) Set A3 (11" 
× 17") paper on the OC table.
3) Press the start key again.
4) The sensor level of the original sensor is automatically checked
and the value with an original - 40 is made as the threshold value
for scanning. (Automatic setting)
5) Execute SIM 43-3.
6) The light reception level of the original sensor is displayed.
The first digit of the copy quantity display shows “A”: Light recep-
tion level display
The first digit of the copy quantity display shows “b”: Original
judgement level display
(The mode selection is made with the magnification ratio display
key.)
7) By changing the paper set on the original table, the original size
LED sensed by the sensor is lighted.
C. Image density adjustment
(1) Copy mode (SIM 46-1)
1) Set a test chart (UKOG-0162FCZZ) on the OC table as shown
below.
2) Put several sheets of A3 or 11" 
× 17" white paper on the test
chart.
3) Execute SIM 46-1.
4) After warmup, shading is performed and the current set value of
the density level is displayed on the display section in 2 digits.
For mode selection, use the density select key.
5) Change the set value with the 10-key to adjust the copy image
density.
6) Make a copy and check that the specification below is satisfied.
<Adjustment specification>
Den-
sity
mode
Dis-
play
lamp
Ex-
posure
level
Sharp Gray
Chart output
Set value
Set
range
Auto
Auto
—
“3” is slightly
copied.
The greater
the set value
is, the
greater the
density is.
The smaller
the set value
is, the
smaller the
density is.
1 
∼
99
Manual
Manual
3
“3” is slightly
copied.
Photo
Photo
3
“3” is slightly
copied.
Toner
save
Manual
/
Photo
3
“3” is slightly
copied.
Open
A
Distance A = Table glass top - OC (SPF) knob 117"
Check the position where the display checked in 
procedure 1) is changed. 
(A)
(B)
Open/close sensor mounting plate
Factory setting : second from the top 
DM-2000
6  –  8
<Adjustment specification>
Mode
Specification
SIM
Set value
Set range
Original off
center mode
(OC mode)
Single:
Center 
±
2.0 mm
SIM
50-13
Add 1:
0.1 mm shift
to R side
Reduce 1:
0.1 mm shift
to L side
1 
∼ 99
Duplex:
Center 
±2.5
mm
b. SPF mode
Note:
● Before performing this adjustment, be sure to check that the
paper off center is properly adjusted.
1) Make a test chart for the center position adjustment and set it on
the SPF.
<Adjustment specification>
Draw a line on a paper in the scanning direction.
2) Make a normal copy from the manual paper feed tray, and com-
pare the copy and the original test chart.
If necessary, perform the following adjustment procedures.
3) Execute SIM 50-16.
4) After warmup, shading is performed and the current set value of
the off center adjustment at each paper feed port is displayed on
the display section in 2 digits.
5) Enter the set value and press the start key.
<Adjustment specification>
Mode
Specification
SIM
Set value
Set range
Original off
center mode
(SPF mode)
Single:
Center 
±
3.0 mm
SIM
50-16
Add 1:
0.1 mm shift
to R side
Reduce 1:
0.1 mm shift
to L side
1 
∼ 99
Duplex:
Center 
±3.5
mm
(8) OC (SPF) open/close detection position adjustment
1) Set A4 or 8 1/2" 
× 11" paper on the OC table.
Check that the document size display on the operation panel in-
dicates the correct size of the set paper.
2) Close the OC (SPF) with a small clearance for insertion of your
hand left, and remove the paper from the OC table.
The document size display does not change from the display in 1).
3) Open the OC (SPF) slowly until the display on the operation panel
changes (all the document size display lamps are turned off), and
measure dimension A shown below under that state.
<Spec value>
OC (SPF) open/close position A: 207 
∼ 302mm
4) If the OC (SPF) open/close position A is not 207 
∼ 302mm, adjust
the open/close sensor mounting plate position as shown below.
(9) Original sensor adjustment (SIM 43-3)
1) Execute SIM 41-2.
2) Set A3 (11" 
× 17") paper on the OC table.
3) Press the start key again.
4) The sensor level of the original sensor is automatically checked
and the value with an original - 40 is made as the threshold value
for scanning. (Automatic setting)
5) Execute SIM 43-3.
6) The light reception level of the original sensor is displayed.
The first digit of the copy quantity display shows “A”: Light recep-
tion level display
The first digit of the copy quantity display shows “b”: Original
judgement level display
(The mode selection is made with the magnification ratio display
key.)
7) By changing the paper set on the original table, the original size
LED sensed by the sensor is lighted.
C. Image density adjustment
(1) Copy mode (SIM 46-1)
1) Set a test chart (UKOG-0162FCZZ) on the OC table as shown
below.
2) Put several sheets of A3 or 11" 
× 17" white paper on the test
chart.
3) Execute SIM 46-1.
4) After warmup, shading is performed and the current set value of
the density level is displayed on the display section in 2 digits.
For mode selection, use the density select key.
5) Change the set value with the 10-key to adjust the copy image
density.
6) Make a copy and check that the specification below is satisfied.
<Adjustment specification>
Den-
sity
mode
Dis-
play
lamp
Ex-
posure
level
Sharp Gray
Chart output
Set value
Set
range
Auto
Auto
—
“3” is slightly
copied.
The greater
the set value
is, the
greater the
density is.
The smaller
the set value
is, the
smaller the
density is.
1 
∼
99
Manual
Manual
3
“3” is slightly
copied.
Photo
Photo
3
“3” is slightly
copied.
Toner
save
Manual
/
Photo
3
“3” is slightly
copied.
Open
A
Distance A = Table glass top - OC (SPF) knob 117"
Check the position where the display checked in 
procedure 1) is changed. 
(A)
(B)
Open/close sensor mounting plate
Factory setting : second from the top 
DM-2000
6  –  8
<Adjustment specification>
Mode
Specification
SIM
Set value
Set range
Original off
center mode
(OC mode)
Single:
Center 
±
2.0 mm
SIM
50-13
Add 1:
0.1 mm shift
to R side
Reduce 1:
0.1 mm shift
to L side
1 
∼ 99
Duplex:
Center 
±2.5
mm
b. SPF mode
Note:
● Before performing this adjustment, be sure to check that the
paper off center is properly adjusted.
1) Make a test chart for the center position adjustment and set it on
the SPF.
<Adjustment specification>
Draw a line on a paper in the scanning direction.
2) Make a normal copy from the manual paper feed tray, and com-
pare the copy and the original test chart.
If necessary, perform the following adjustment procedures.
3) Execute SIM 50-16.
4) After warmup, shading is performed and the current set value of
the off center adjustment at each paper feed port is displayed on
the display section in 2 digits.
5) Enter the set value and press the start key.
<Adjustment specification>
Mode
Specification
SIM
Set value
Set range
Original off
center mode
(SPF mode)
Single:
Center 
±
3.0 mm
SIM
50-16
Add 1:
0.1 mm shift
to R side
Reduce 1:
0.1 mm shift
to L side
1 
∼ 99
Duplex:
Center 
±3.5
mm
(8) OC (SPF) open/close detection position adjustment
1) Set A4 or 8 1/2" 
× 11" paper on the OC table.
Check that the document size display on the operation panel in-
dicates the correct size of the set paper.
2) Close the OC (SPF) with a small clearance for insertion of your
hand left, and remove the paper from the OC table.
The document size display does not change from the display in 1).
3) Open the OC (SPF) slowly until the display on the operation panel
changes (all the document size display lamps are turned off), and
measure dimension A shown below under that state.
<Spec value>
OC (SPF) open/close position A: 207 
∼ 302mm
4) If the OC (SPF) open/close position A is not 207 
∼ 302mm, adjust
the open/close sensor mounting plate position as shown below.
(9) Original sensor adjustment (SIM 43-3)
1) Execute SIM 41-2.
2) Set A3 (11" 
× 17") paper on the OC table.
3) Press the start key again.
4) The sensor level of the original sensor is automatically checked
and the value with an original - 40 is made as the threshold value
for scanning. (Automatic setting)
5) Execute SIM 43-3.
6) The light reception level of the original sensor is displayed.
The first digit of the copy quantity display shows “A”: Light recep-
tion level display
The first digit of the copy quantity display shows “b”: Original
judgement level display
(The mode selection is made with the magnification ratio display
key.)
7) By changing the paper set on the original table, the original size
LED sensed by the sensor is lighted.
C. Image density adjustment
(1) Copy mode (SIM 46-1)
1) Set a test chart (UKOG-0162FCZZ) on the OC table as shown
below.
2) Put several sheets of A3 or 11" 
× 17" white paper on the test
chart.
3) Execute SIM 46-1.
4) After warmup, shading is performed and the current set value of
the density level is displayed on the display section in 2 digits.
For mode selection, use the density select key.
5) Change the set value with the 10-key to adjust the copy image
density.
6) Make a copy and check that the specification below is satisfied.
<Adjustment specification>
Den-
sity
mode
Dis-
play
lamp
Ex-
posure
level
Sharp Gray
Chart output
Set value
Set
range
Auto
Auto
—
“3” is slightly
copied.
The greater
the set value
is, the
greater the
density is.
The smaller
the set value
is, the
smaller the
density is.
1 
∼
99
Manual
Manual
3
“3” is slightly
copied.
Photo
Photo
3
“3” is slightly
copied.
Toner
save
Manual
/
Photo
3
“3” is slightly
copied.
Open
A
Distance A = Table glass top - OC (SPF) knob 117"
Check the position where the display checked in 
procedure 1) is changed. 
(A)
(B)
Open/close sensor mounting plate
Factory setting : second from the top 
DM-2000
6  –  8
<Adjustment specification>
Mode
Specification
SIM
Set value
Set range
Original off
center mode
(OC mode)
Single:
Center 
±
2.0 mm
SIM
50-13
Add 1:
0.1 mm shift
to R side
Reduce 1:
0.1 mm shift
to L side
1 
∼ 99
Duplex:
Center 
±2.5
mm
b. SPF mode
Note:
● Before performing this adjustment, be sure to check that the
paper off center is properly adjusted.
1) Make a test chart for the center position adjustment and set it on
the SPF.
<Adjustment specification>
Draw a line on a paper in the scanning direction.
2) Make a normal copy from the manual paper feed tray, and com-
pare the copy and the original test chart.
If necessary, perform the following adjustment procedures.
3) Execute SIM 50-16.
4) After warmup, shading is performed and the current set value of
the off center adjustment at each paper feed port is displayed on
the display section in 2 digits.
5) Enter the set value and press the start key.
<Adjustment specification>
Mode
Specification
SIM
Set value
Set range
Original off
center mode
(SPF mode)
Single:
Center 
±
3.0 mm
SIM
50-16
Add 1:
0.1 mm shift
to R side
Reduce 1:
0.1 mm shift
to L side
1 
∼ 99
Duplex:
Center 
±3.5
mm
(8) OC (SPF) open/close detection position adjustment
1) Set A4 or 8 1/2" 
× 11" paper on the OC table.
Check that the document size display on the operation panel in-
dicates the correct size of the set paper.
2) Close the OC (SPF) with a small clearance for insertion of your
hand left, and remove the paper from the OC table.
The document size display does not change from the display in 1).
3) Open the OC (SPF) slowly until the display on the operation panel
changes (all the document size display lamps are turned off), and
measure dimension A shown below under that state.
<Spec value>
OC (SPF) open/close position A: 207 
∼ 302mm
4) If the OC (SPF) open/close position A is not 207 
∼ 302mm, adjust
the open/close sensor mounting plate position as shown below.
(9) Original sensor adjustment (SIM 43-3)
1) Execute SIM 41-2.
2) Set A3 (11" 
× 17") paper on the OC table.
3) Press the start key again.
4) The sensor level of the original sensor is automatically checked
and the value with an original - 40 is made as the threshold value
for scanning. (Automatic setting)
5) Execute SIM 43-3.
6) The light reception level of the original sensor is displayed.
The first digit of the copy quantity display shows “A”: Light recep-
tion level display
The first digit of the copy quantity display shows “b”: Original
judgement level display
(The mode selection is made with the magnification ratio display
key.)
7) By changing the paper set on the original table, the original size
LED sensed by the sensor is lighted.
C. Image density adjustment
(1) Copy mode (SIM 46-1)
1) Set a test chart (UKOG-0162FCZZ) on the OC table as shown
below.
2) Put several sheets of A3 or 11" 
× 17" white paper on the test
chart.
3) Execute SIM 46-1.
4) After warmup, shading is performed and the current set value of
the density level is displayed on the display section in 2 digits.
For mode selection, use the density select key.
5) Change the set value with the 10-key to adjust the copy image
density.
6) Make a copy and check that the specification below is satisfied.
<Adjustment specification>
Den-
sity
mode
Dis-
play
lamp
Ex-
posure
level
Sharp Gray
Chart output
Set value
Set
range
Auto
Auto
—
“3” is slightly
copied.
The greater
the set value
is, the
greater the
density is.
The smaller
the set value
is, the
smaller the
density is.
1 
∼
99
Manual
Manual
3
“3” is slightly
copied.
Photo
Photo
3
“3” is slightly
copied.
Toner
save
Manual
/
Photo
3
“3” is slightly
copied.
Open
A
Distance A = Table glass top - OC (SPF) knob 117"
Check the position where the display checked in 
procedure 1) is changed. 
(A)
(B)
Open/close sensor mounting plate
Factory setting : second from the top 
DM-2000
6  –  8
Page of 16
Display

Sharp DM-2000 (serv.man5) Service Manual ▷ Download

Found More:

DM-2000 (serv.man5) Service Manuals

Preview DownloadPagesSize
GDM-2000TC Service Manual 29 1.22 MB
DM-2000 (serv.man3) DM2000 Service Manual-General Specifications Service Manual 12 179.37 KB
DM-2000 (serv.man4) DM2000 Service Manual-Consumable Parts External Views Internal Structures Service Manual 9 441.4 KB
DM-2000 (serv.man6) DM2000 Service Manual-Simulations Flash Rom Version Up Procedure Service Manual 14 208.81 KB
DM-2000 (serv.man7) DM2000 Service Manual-Trouble Code List User Setup Service Manual 15 272.12 KB
DM-2000 (serv.man8) DM2000 Service Manual-Disassembly Assembly Electrical Section Service Manual 18 1.69 MB
DM-2000 (serv.man10) DM2000-Operation Manual Part1 User Manual / Operation Manual 28 880.59 KB
DM-2000 (serv.man11) DM2000-Operation Manual Part2 User Manual / Operation Manual 10 406.13 KB
DM-2000 (serv.man12) DM2000-Operation Manual Part3 User Manual / Operation Manual 18 216.41 KB
DM-2000 (serv.man13) DM2000-Operation Manual Part4 User Manual / Operation Manual 28 487.6 KB
DM-2000 (serv.man9) Parts guide Service Manual / Parts Guide 39 2.01 MB
DM-2000 (serv.man2) DM2000 Specifications Service Manual / Specification 8 79.97 KB
DM-2000 (serv.man20) Manual paper feed roller material change. Service Manual / Technical Bulletin 5 342.3 KB
DM-2000 (serv.man21) MATERIAL CHANGE PAPER FEED SHEET Service Manual / Technical Bulletin 4 354.66 KB
DM-2000 (serv.man22) Attachment of a high temperature Caution Label. Service Manual / Technical Bulletin 2 108.07 KB
DM-2000 (serv.man23) Countermeasure against peeling of the fusing front PG sheet Service Manual / Technical Bulletin 2 46.93 KB
DM-2000 (serv.man24) Countermeasure against paper jam when ejecting Service Manual / Technical Bulletin 2 92.8 KB
DM-2000 (serv.man25) Countermeasure against U2-40 trouble due to power supply noise. Service Manual / Technical Bulletin 1 1.08 MB
DM-2000 (serv.man26) CHANGE OF PARTS (Base Plate Unit 2 Delivery Frame Unit MCU PWB) Service Manual / Technical Bulletin 1 26.04 KB
DM-2000 (serv.man27) Countermeasure against paper jam due to deformation of the fusing upper paper guide sheet. Service Manual / Technical Bulletin 2 47.77 KB
DM-2000 (serv.man28) Countermeasure against skewing due to gap in Tray Guide R Service Manual / Technical Bulletin 2 185.54 KB
DM-2000 (serv.man29) Information of parts change Service Manual / Technical Bulletin 2 791.29 KB
DM-2000 (serv.man30) Part number for Panther-series Power Switch Service Manual / Technical Bulletin 1 11.12 KB
DM-2000 (serv.man31) New supply of EEPROM for service Service Manual / Technical Bulletin 1 7.19 KB
DM-2000 (serv.man32) Change to shape of rear plate to prevent dislocation Service Manual / Technical Bulletin 1 183.36 KB
DM-2000 (serv.man33) Countermeasure against manual feed paper jams, due to contamination of drive section Service Manual / Technical Bulletin 2 278.17 KB
DM-2000 (serv.man34) Improved durability of cam transmission arm in manual paper feed unit Service Manual / Technical Bulletin 1 13.01 KB
DM-2000 (serv.man35) Countermeasure against breakage of the fusing rear paper guide rib Service Manual / Technical Bulletin 1 115.91 KB
DM-2000 (serv.man36) Countermeasure against breakage of the discharge holder claw Service Manual / Technical Bulletin 1 93.76 KB
DM-2000 (serv.man37) Countermeasure against paper jam when ejecting paper Service Manual / Technical Bulletin 1 70.95 KB
DM-2000 (serv.man38) Countermeasure against F1-06 errors Service Manual / Technical Bulletin 1 54.34 KB
DM-2000 (serv.man39) Countermeasure for duplex print problem in PCL firmware version 4.53 Service Manual / Technical Bulletin 1 10.96 KB
DM-2000 (serv.man40) Parts change information for PS transport roller Service Manual / Technical Bulletin 1 13.26 KB
DM-2000 (serv.man41) Countermeasure for black stripes when using SPF, and for occurrence of E7-04 error message Service Manual / Technical Bulletin 2 37.59 KB
DM-2000 (serv.man42) Countermeasure against skewing when feeding from cassette Service Manual / Technical Bulletin 1 20.88 KB
DM-2000 (serv.man43) Design of feeding rollers is changed to improve quality of paper feeding Service Manual / Technical Bulletin 2 52.57 KB
DM-2000 (serv.man44) Information of parts change (MCU PWB) Service Manual / Technical Bulletin 1 16.99 KB
DM-2000 (serv.man45) Information of parts change (document feed) Service Manual / Technical Bulletin 1 12.83 KB
DM-2000 (serv.man46) Correction of E7-04 error Service Manual / Technical Bulletin 1 12.2 KB
DM-2000 (serv.man47) Parts change information (paper feeding unit process unit side door unit) Service Manual / Technical Bulletin 2 53.14 KB
DM-2000 (serv.man48) Countermeasure against right door detection error Service Manual / Technical Bulletin 1 951.49 KB
DM-2000 (serv.man49) Update to the PCL firmware (Version 4.53) Service Manual / Technical Bulletin 1 15.13 KB
DM-2000 (serv.man50) New supply of a service part (paper feed roller rubber) Service Manual / Technical Bulletin 1 12.42 KB
DM-2000 (serv.man51) Countermeasure against abnormal noise from the 2nd transport clutch Service Manual / Technical Bulletin 1 33.05 KB
DM-2000 (serv.man52) Version change of the maintenance (firmware download) software Service Manual / Technical Bulletin 1 13.34 KB
DM-2000 (serv.man53) Parts change information (MCU PWB) Service Manual / Technical Bulletin 1 12.86 KB
DM-2000 (serv.man54) Increase of power supply margin on PWB due to change of fuse Service Manual / Technical Bulletin 1 394.48 KB
DM-2000 (serv.man55) Change of cassette lock claws Service Manual / Technical Bulletin 1 23.33 KB
DM-2000 (serv.man56) New supply of service part Service Manual / Technical Bulletin 1 23.98 KB
DM-2000 (serv.man57) Reducing white stripes on the CRU unit Service Manual / Technical Bulletin 1 21.37 KB
DM-2000 (serv.man58) Parts change information Service Manual / Technical Bulletin 2 530.63 KB
DM-2000 (serv.man59) Information about the part code of the delivery frame Service Manual / Technical Bulletin 1 21.89 KB
DM-2000 (serv.man60) Parts change information Service Manual / Technical Bulletin 2 205.19 KB
DM-2000 (serv.man61) New supply of fusing unit adding a cleaning felt AS Service Manual / Technical Bulletin 1 21.57 KB
DM-2000 (serv.man62) Parts change Service Manual / Technical Bulletin 1 21.48 KB
DM-2000 (serv.man63) New supply of a service part described in AR161 200 ref 079 Service Manual / Technical Bulletin 1 23.38 KB
DM-2000 (serv.man64) Software version upgrade of the main ROM for simplex models (Correction of jam detection error in special conditions) Service Manual / Technical Bulletin 1 22.59 KB
DM-2000 (serv.man65) Countermeasure against folding of the corner of copying paper on duplex print Service Manual / Technical Bulletin 1 40.57 KB
DM-2000 (serv.man66) Countermeasure against oblique feed of the cassette Service Manual / Technical Bulletin 1 33.04 KB
DM-2000 (serv.man67) Countermeasure against soiling of upper heat roller. Service Manual / Technical Bulletin 2 111.82 KB
DM-2000 (serv.man68) Parts change. Service Manual / Technical Bulletin 3 117.18 KB
DM-2000 (serv.man69) Support of double feed during cassette paper feed and document double feed. Service Manual / Technical Bulletin 4 203.74 KB
DM-2000 (serv.man70) Countermeasure against L4-01 (main motor lock) and paper jam. Service Manual / Technical Bulletin 2 345.54 KB
DM-2000 (serv.man71) Change of the toner motor (toner not supplied). Service Manual / Technical Bulletin 1 64.13 KB
DM-2000 (serv.man72) Countermeasure against job separator home position detection error. Service Manual / Technical Bulletin 2 99.41 KB
DM-2000 (serv.man73) Improvement of the manual paper feeding tray lock. Service Manual / Technical Bulletin 1 101.53 KB
DM-2000 (serv.man74) Application of grease to the paper feed cassette rail. Service Manual / Technical Bulletin 1 100.08 KB
DM-2000 (serv.man75) Countermeasure against breakage of the 2nd gear teeth. (WHITE) Service Manual / Technical Bulletin 2 87.63 KB
DM-2000 (serv.man76) Parts change for the productivity improvement. (WHITE) Service Manual / Technical Bulletin 2 83.92 KB
DM-2000 (serv.man77) Version upgrade of the PCL firmware. (WHITE) Service Manual / Technical Bulletin 2 84.18 KB
DM-2000 (serv.man78) Caution when replacing the MCU. (WHITE) Service Manual / Technical Bulletin 1 60.5 KB
DM-2000 (serv.man79) Version upgrade of the main body software. (Update to ref.067)(WHITE) Service Manual / Technical Bulletin 1 63.37 KB
DM-2000 (serv.man80) Change of the operation instruction label. (WHITE) Service Manual / Technical Bulletin 2 102.54 KB
DM-2000 (serv.man81) Version upgrade of the main body software. (WHITE) Service Manual / Technical Bulletin 1 36.39 KB
DM-2000 (serv.man82) Change of the operation instruction label. (WHITE) Service Manual / Technical Bulletin 2 72.15 KB
DM-2000 (serv.man83) Change of the shifter gear (50T). Service Manual / Technical Bulletin 2 62.9 KB
DM-2000 (serv.man84) Change of the LSU unit. (WHITE) Service Manual / Technical Bulletin 1 48.88 KB
DM-2000 (serv.man85) Parts change of the fusing unit. (WHITE) Service Manual / Technical Bulletin 1 49.83 KB
DM-2000 (serv.man86) Supply of the paper feed roller as a service part. (WHITE) Service Manual / Technical Bulletin 1 126.36 KB
DM-2000 (serv.man87) Material change of the fusing gear (45T). (WHITE) Service Manual / Technical Bulletin 1 89.86 KB
DM-2000 (serv.man88) Version upgrade of the software of the main body. (WHITE) Service Manual / Technical Bulletin 1 102.22 KB
DM-2000 (serv.man89) About the expanded memory. (WHITE) Service Manual / Technical Bulletin 2 109.01 KB
DM-2000 (serv.man90) 1.Change of the packing material. 2.Correction of the parts guide. 3.Addition of an original caution label. (WHITE) Service Manual / Technical Bulletin 2 143.62 KB
DM-2000 (serv.man91) Developer Unit Improvement To Correct Clearance Between MX Roller Shaft And Shaft Bearing. (WHITE) Service Manual / Technical Bulletin 2 89.22 KB
DM-2000 (serv.man92) Change Of The Photoconductor.(WHITE) Service Manual / Technical Bulletin 1 61.61 KB
DM-2000 (serv.man93) Fax Kit Problems. (WHITE) Service Manual / Technical Bulletin 2 74.09 KB
DM-2000 (serv.man94) 1.Change Of The LSU Unit. 2.Change Of The Lamp Base Plate. 3.Change Of The LCD Spacer. (WHITE) Service Manual / Technical Bulletin 2 76.86 KB
DM-2000 (serv.man95) 1.Version Upgrade Of The CDROM. 2.Version Upgrade Of The PCL Firmware. 3.Release Of The Fax Program. 4.Parts Change For Better Productivity. 5.Supply Of Expanded Memory For The PCL PWB. (WHITE) Service Manual / Technical Bulletin 3 74.52 KB
DM-2000 (serv.man96) Noisy Laser Unit. (WHITE) Service Manual / Technical Bulletin 1 58.08 KB
DM-2000 (serv.man97) Correction To The Parts Guide. (WHITE) Service Manual / Technical Bulletin 2 79.58 KB
DM-2000 (serv.man98) (Revision to reference 042) 1.Change Of The Fusing Lower Frame. 2.Change Of The SPF Rack Cover. 3.Countermeasure Against Poor Insertion Of The Motherboard Connector. 4.Change Of The Rubber Cushion. (WHITE) Service Manual / Technical Bulletin 3 85.3 KB
DM-2000 (serv.man99) Change Of The DV Sheet. (WHITE) Service Manual / Technical Bulletin 1 75.22 KB
DM-2000 (serv.man100) Change Of The Default Values. (WHITE) Service Manual / Technical Bulletin 1 66.59 KB
DM-2000 (serv.man101) Satisfaction Of Energy Star. (WHITE) Service Manual / Technical Bulletin 2 70.72 KB
DM-2000 (serv.man102) 1.Change Of The SPF Glass Sheet R. 2.Dimensions Change Of The PS Transport Roller. 3.Material Change Of The Copy Operation PWB. (WHITE) Service Manual / Technical Bulletin 3 92.51 KB
DM-2000 (serv.man103) 1.Shape Change Of The OP PWB Shield And Addition Of A Shield Plate Card. 2.Shape Change Of The Copy Lamp Unit. 3.Disuse Of The Sub Blade Earth Plate. (WHITE) Service Manual / Technical Bulletin 2 67.57 KB
DM-2000 (serv.man104) Version Upgrade Of The Main Body Software. (WHITE) Service Manual / Technical Bulletin 1 61.42 KB
DM-2000 (serv.man105) Parts Change For Better Productivity. (WHITE) Service Manual / Technical Bulletin 2 68.55 KB
DM-2000 (serv.man106) 1.Change Of The Fusing Lower Frame. 2.Change Of the SPF Rack Cover. 3.Countermeasure Against Poor Insertion Of The Motherboard Connector. 4.Change Of The Rubber Cushion. (WHITE) Service Manual / Technical Bulletin 3 85.16 KB
DM-2000 (serv.man107) Increase Of Strength Of The Fusing Gear. (WHITE) Service Manual / Technical Bulletin 1 62.33 KB
DM-2000 (serv.man108) Mounting The Dehumidifying Heater In The Optical Unit On The Market. (WHITE) Service Manual / Technical Bulletin 4 221.25 KB
DM-2000 (serv.man109) 1.Countermeasure Against Abnormal Noise. 2.Countermeasure Against Shifter Operation Error. 3.Shape Change Of The Cooling Fan Duct. (WHITE) Service Manual / Technical Bulletin 3 79.4 KB
DM-2000 (serv.man110) 1.Change Of The Operation Panel Exterior. 2.Screw Change. (WHITE) Service Manual / Technical Bulletin 2 70.13 KB
DM-2000 (serv.man111) Software Version Update Of The Main Body. (WHITE) Service Manual / Technical Bulletin 1 61.72 KB
DM-2000 (serv.man112) Parts Change For Better Productivity. (WHITE) Service Manual / Technical Bulletin 2 71.5 KB
DM-2000 (serv.man113) 1.Change Of The Discharge Holder. 2.Shape Change Of The Copy Key. 3.Addition Of the Harness Protection Sheet. (WHITE) Service Manual / Technical Bulletin 2 85.08 KB
DM-2000 (serv.man114) Parts Change For Better Productivity. (WHITE) Service Manual / Technical Bulletin 2 70.16 KB
DM-2000 (serv.man115) Corrections To The Service Manual. (WHITE) Service Manual / Technical Bulletin 1 130.4 KB
DM-2000 (serv.man116) Addition To The Service Manual. (WHITE) Service Manual / Technical Bulletin 1 65.16 KB
DM-2000 (serv.man117) 1.Shape Change Of Fusing Cover. 2.Countermeasure Against Abnormal Noise. (WHITE) Service Manual / Technical Bulletin 2 79.68 KB
DM-2000 (serv.man118) Disuse Of Screws. (WHITE) Service Manual / Technical Bulletin 2 130.02 KB
DM-2000 (serv.man119) 1.Change Of Harness Treating Method. 2.Shape Change Of Separator Lever F. (WHITE) Service Manual / Technical Bulletin 2 114.22 KB
DM-2000 (serv.man120) Parts Change For Better Productivity. (WHITE) Service Manual / Technical Bulletin 2 82 KB
DM-2000 (serv.man121) 1.Shape Change Of Rear Exterior. 2.Shape Change Of MCU Fixing Plate. 3.Shape Change Of Sensor Fixing Plate And Optical Base Plate. (WHITE) Service Manual / Technical Bulletin 2 71.74 KB
DM-2000 (serv.man122) 1.Change Of 3-Terminal Regulator. 2.Change Of Corner Frame R Re-inforce Plate. 3.Shape Change Of Delivery Tray. (WHITE) Service Manual / Technical Bulletin 2 70.89 KB
DM-2000 (serv.man123) Corrections To The Service Manual. (WHITE) Service Manual / Technical Bulletin 2 280.47 KB
DM-2000 (serv.man124) 1.Change Of Delivery Earth Spring A. 2.Disuse Of Fusing Front PG Adjusting Shaft. 3.Shape Change Of Base Plate Rail R. (WHITE) Service Manual / Technical Bulletin 2 71.6 KB
DM-2000 (serv.man125) 1.Shape Change Of DMC Actuator. 2.Change Of Front Cabinet. 3.Disuse Of Screws. (WHITE) Service Manual / Technical Bulletin 4 557.37 KB
DM-2000 (serv.man126) New Supply Of Process Sub-unit. (WHITE) Service Manual / Technical Bulletin 2 65.11 KB
DM-2000 (serv.man127) Countermeasure For Envelopes Postcards Feeding Failure Problem. (WHITE) Service Manual / Technical Bulletin 2 79.75 KB
DM-2000 (serv.man128) Shape Change Of Pipe Shutter. (WHITE) Service Manual / Technical Bulletin 1 36.68 KB
DM-2000 (serv.man129) Correction To The Parts Guide. (WHITE) Service Manual / Technical Bulletin 1 76.03 KB
DM-2000 (serv.man130) Countermeasure Against Jam By Catching Thin Paper In The Drum. (WHITE) Service Manual / Technical Bulletin 2 61.84 KB
DM-2000 (serv.man131) Countermeasure Against The Improper Movement Of ARTR2 (Job Separator). (WHITE) Service Manual / Technical Bulletin 2 95.25 KB
DM-2000 (serv.man132) 1.Change Of TC BC Interface Electrode Spring. 2.Change Of MCU PWB Parts. 3.Change Of Mirror Motor. (WHITE) Service Manual / Technical Bulletin 2 27.21 KB
DM-2000 (serv.man133) 1.Correspondance To EMI. 2.Change Of PS Roller Shaft. 3.Shape Change Of DMC Actuator. 4.Addition Of Front Cover Label. (WHITE) Service Manual / Technical Bulletin 1 25.54 KB
DM-2000 (serv.man134) Change Of Reverse Gate. (WHITE) Service Manual / Technical Bulletin 1 23.5 KB
DM-2000 (serv.man135) 1.Prevention Against Vibration Of Job Separator. 2.Shape Change Of Separator Lever R. 3.Shape Change Of Full Detection Lever. (WHITE) Service Manual / Technical Bulletin 1 26.12 KB
DM-2000 (serv.man136) 1.Countermeasure Against Vertical Stripes. 2.Dry Heater Change. 3.Prevention Against Disengagement Of Bearing Due To Deformation Of Delivery Earth Plate. 4.Countermeasure Against White Stripes In The Halftone Mode. 5.Change Of LED On The Operation PWB. (WHITE) Service Manual / Technical Bulletin 2 41.14 KB
DM-2000 (serv.man137) F5-02 Change Of Connector To That With Slider. (WHITE) Service Manual / Technical Bulletin 1 22.94 KB
DM-2000 (serv.man138) Parts Guide Correction. (WHITE) Service Manual / Technical Bulletin 1 23.02 KB
DM-2000 (serv.man139) Supply Of Service Unit For The Process Unit. (WHITE) Service Manual / Technical Bulletin 2 57.81 KB
DM-2000 (serv.man140) Correction Of The Flash Rom Version Update (Issue of No.2.03). (WHITE) Service Manual / Technical Bulletin 3 470.4 KB
DM-2000 (serv.man141) Update Of The Software Version Due To Release Of The Option Electronics Sort Board. (WHITE) Service Manual / Technical Bulletin 3 473.83 KB
DM-2000 (serv.man142) Update Of The Software Version Due To Release Of The Option Printer Board. (WHITE) Service Manual / Technical Bulletin 3 688.27 KB
DM-2000 (serv.man143) Supply Of Individual Parts Of Copy Lamp Unit. (WHITE) Service Manual / Technical Bulletin 2 61.58 KB
DM-2000 (serv.man144) Correction Of The Flash ROM Version Upgrade. (WHITE) Service Manual / Technical Bulletin 3 684.88 KB
DM-2000 (serv.man145) Correction To The Parts Guide. (WHITE) Service Manual / Technical Bulletin 1 18.52 KB
DM-2000 (serv.man146) Version 4.10 Firmware (Sent out as FF COP 0890 Service Manual / Technical Bulletin 1 10.36 KB
DM-2000 (serv.man147) Flash Upgrade Procedure (Sent out as FF COP 085)(Originally written for AR161 200 only). Service Manual / Technical Bulletin 3 325.04 KB
DM-2000 (serv.man14) AR161 200 DM2000-Firmware for coin vendor Ver7.05 Driver / Update 243.42 KB
DM-2000 (serv.man15) DM2000-Firmware Version 5.32. Please refer to Firmware revision table for details. Driver / Update 240.77 KB
DM-2000 (serv.man16) DM2000-Firmware Version 5.29 Driver / Update 236.8 KB
DM-2000 (serv.man17) Version 3.1 CD printer drivers for Windows 3.1 3.11. Includes drivers for PCL5e Postscript. Driver / Update 2.06 MB
DM-2000 (serv.man18) Version 3.1 CD printer drivers for Windows NT4. Includes drivers for PCL5e, PCL6, Postscript. Driver / Update 1.96 MB
DM-2000 (serv.man19) Version 3.1 CD printer drivers for Windows 95 98. Includes drivers for PCL5e, PCL6, Postscript. Driver / Update 3.13 MB
DM-2000 DM2000-Handy Guide Handy Guide 25 313.24 KB
DM-2000 (serv.man148) MSDS F-00841 Regulatory Data 2 12.59 KB
DM-2000 (serv.man149) MSDS F-30841 Regulatory Data 2 11.41 KB
DM-2000 (serv.man150) Environmental Data Sheet Regulatory Data 1 4.49 KB

RANDOM: