DM-2000 (serv.man5). DM2000 Service Manual-Unpacking Installation Adjustments — Sharp Copying Equipment Service Manual (repair manual)

Model
DM-2000 (serv.man5)
Pages
16
Size
669.84 KB
Type
PDF
Document
Service Manual
Brand
Device
Copying Equipment / DM2000 Service Manual-Unpacking Installation Adjustments
File
dm-2000-sm5.pdf
Date

View Sharp DM-2000 (serv.man5) Service Manual online

CODE: 00ZDM2000/A1E
NETWORK LASER
SYSTEM
MODEL
DM-2000
[ 1 ] GENERAL  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  1  -  1
[ 2 ] SPECIFICATIONS  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  2  -  1
[ 3 ] CONSUMABLE  PARTS  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  3  -  1
[ 4 ] EXTERNAL  VIEWS  AND  INTERNAL  STRUCTURES  .  .  .  4  -  1
[ 5 ] UNPACKING  AND  INSTALLATION  .  .  .  .  .  .  .  .  .  .  .  .  .  5  -  1
[ 6 ] ADJUSTMENTS .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  6  -  1
[ 7 ] SIMULATIONS  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  7  -  1
[ 8 ] FLASH  ROM  VERSION  UP  PROCEDURE  .  .  .  .  .  .  .  .  .  8  -  1
[ 9 ] TROUBLE  CODE  LIST  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  9  -  1
[10] USER  SETUP .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  10  -  1
[11] DISASSEMBLY  AND  ASSEMBLY  .  .  .  .  .  .  .  .  .  .  .  .  .  11  -  1
[12] ELECTRICAL  SECTION  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  12  -  1
CONTENTS
Parts marked with “  ” are important for maintaining the safety of the set. Be sure to replace these parts with specified
ones for maintaining the safety and performance of the set.
SHARP CORPORATION
DM-2000
[5] UNPACKING AND INSTALLATION
1. Installing conditions
1) Copier installation
Do not install your copier in areas that are:
● damp, humid, or very dusty
● exposed to direct sunlight
● poorly ventilated
● subject to extreme temperature or humidity changes, e.g., near
an air conditioner or heater.
● Be sure to allow the required space around the machine for ser-
vicing and proper ventilation.
2) Power source
● Use an exclusive-use power outlet. If the power plug of this
machine is inserted into a power outlet commonly used with
other illumination units, flickers of the lamp may be result. Use
a power outlet which is not used commonly with any illumination
units.
● Avoid complex wiring.
3) Grounding wire connection.
● To avoid danger, be sure to connect a grounding wire. If no
grounding wire is connected and a leakage occurs, a fire or an
electric shock may be result.
2. Removal of protective material and
fixing screw
1) Remove all tapes and protective material.
● Remove all tapes, then open the document cover and remove
the protective material of sheet shape
2) Remove the fixing screw.
● Use a coin to remove the fixing screw.
● The fixing screw is required when transporting the machine.
Keep it in the tray. (Refer to the later description.)
3. Installation of developing cartridge
1) Remove the new TD cartridge from the bag. Hold the cartridge on
both sides and shake it horizontally four or five times.
2) Remove the protective cover from the TD cartridge by unlatching
three cover hooks from the holes on the cartridge and then pulling
the cover in the direction indicated by the arrow in the illustration.
3) Open the bypass tray. Lift slightly on the side cover and slide the
cover out until it stops.
4) Push gently on both sides of the front cover to open the cover.
4 or 5 times
4" (10 cm)
DM-2000
5 – 1
5) Gently insert the TD cartridge along the guides until it locks in
place.
Note: If dirt or dust is adhered to the TD cartridge, remove it
before installing the cartridge.
6) Close the front cover by pushing both sides with your hands and
then close the side cover by pressing the handle on the cover.
The  indicator will go out.
Cautoion: When closing the covers, be sure to close the front
cover securely and then close the side cover. If the
covers are closed in the wrong order, the covers may
be damaged.
4. Removal and storage of fixing screw
1) Gently lift and pull out the paper tray until it stops. 
2) Hold the paper pressure plate and turn the fixing screw in the
arrow direction.
3) Store the fixing pin and the fixing screw in the tray.
● Store the fixing screw which was removed in the above proce-
dure 2 and the fixing screw which was removed in procedure 2
of 2.
● Removal of protective material and fixing screw in the storage
place in the tray.
5. Changing the copy paper size in the
tray
1) Gently lift and pull out the paper tray until it stops.
2) Push the pressure plate down until it locks in place.
3) Squeeze the lock lever of the front guide and slide the front guide
to match the width of the paper.
4) Move the left guide to the appropriate slot as marked on the tray.
● When using 11" ×17" copy paper, store the left guide in the slot
at the left front of the paper tray.
5) Load copy paper into the tray.
6) Place the appropriate label to indicate the selected paper size into
the recess on the right front side of the paper tray.
7) Push the paper tray firmly back into the DM System.
8) Turn the power switch on.
A
B
Pressure
plate
lock
Screw
Front guide
Left guide
DM-2000
5  –  2
9) To set the selected paper size, press the PAPER SIZE ENTER
key.
● The selected paper feed location indicator will blink and the cor-
responding paper size (which is currently set) indicator will light
up steadily. All other indicators will go out.
Note: For paper size setting, ensure that the COPY mode has
been selected. However, if copying, printing or facsimile
printing is being performed, paper size setting cannot be
made even in the COPY mode.
10) Use the TRAY SELECT key to select the paper tray of which the
paper size has been changed.
● Each time the TRAY SELECT key is pressed, a paper tray will
be indicated with a blinking paper feed location indicator.
11) Use the ORIGINAL SIZE ENTER key to select the paper size
which is set.
● Each time the ORIGINAL SIZE ENTER key is pressed, a paper
size will be indicated with a paper size indicator.
12) Press the START key and then the PAPER SIZE ENTER key.
● To change the paper size setting of another tray, repeat steps
10) to 11) after pressing the START key.
6. Installing the printer driver
To use this printer with your computer, you must install the printer
driver.
Install the printer driver using the supplied SHARP Software CD-ROM.
This kit is supplied with the following printer drivers:
● PCL6 for Windows 95/98
● PCL6 for Windows NT 4.0
● PCL5e for Windows 95/98
● PCL5e for Windows NT 4.0
Note:
● It is recommended that you install the PCL6 printer driver. If
you have a problem printing from older software using the
PCL6 driver, remove it and install the PCL5e driver.
● The printer driver data in the CD-ROM can be copied to flop-
py disks.
1. Double-click  “My Computer”,  “Dm2000” and “Makedisk”.
2. Double-click “Makedisk.exe”.
3. Follow the on-screen instructions.
Before installation, make sure that:
● You read the README.TXT file which is contained on the SHARP
Software CD-ROM. This file contains the information and restrictions
for using the printer.
● The printer is connected properly with the computer or network.
● The printer is loaded with paper.
● The printer is turned on and on-line (the ON LINE light is lit).
● You quit all application software that is running on your computer.
● Your computer meets the following hardware and software require-
ments:
Computer Type
IBM PC/AT or compatible computer equipped
with a bi-directional parallel interface and CD-
ROM drive
Operating System Windows 95, Windows 98, Windows NT 4.0
CPU
Windows 95:
486SX or better
Windows 98:
486DX/66 MHz or better
(Pentium or better is
recommended.)
Windows NT 4.0:
486/25 MHz or better
RAM
Windows 95:
8 MB or more (12 MB or
more is recommended.)
Windows 98:
16 MB or more (32 MB or
more is recommended.)
Windows NT 4.0:
16 MB or more
This procedure uses the following drive name in examples:
Drive R: CD-ROM drive (holds the CD-ROM containing the printer
drivers)
Change the drive name as required according to your environment.
A. Installing onto Windows 95
This printer is compatible with plug & play. If your computer is incom-
patible with plug & play or if you want to use this printer as a network
printer, refer to “Installing onto Windows 95/98 without Using the Plug
& Play Function”.
1) Turn the computer on and start Windows 95.
Note: Depending on which version of Windows you are using, the
display examples in this step may differ from those on your
system.
● Either the “Update Device Driver Wizard” window or the “New
Hardware Found” window may appear automatically.
Note: If neither the “Update Device Driver Wizard” window nor
the  “New Hardware Found” window appear, refer to “In-
stalling Windows 95/98 without Using the Plug & Play
Function”.
DM-2000
5  –  3
● If the “Update Device Driver Wizard” window appears, click the
[Next] button and proceed to step 2).
● If the “New Hardware Found” window appears, perform the fol-
lowing steps:
<1> Choose  “Driver from disk provided by hardware manufac-
turer” and click the [OK] button.
<2> When the “Install From Disk” window appears, insert the
SHARP Software CD-ROM into the CD-ROM drive, type
R:\English\WinXX and click the [OK] button.
<3> Choose the appropriate printer driver from those listed below
and click the [OK] button.
● PCL6 Printer Driver:SHARP DM-2000 Series PCL6
● PCL5e Printer Driver:SHARP DM-2000 Series PCL5e
Note: It is recommended that you install the PCL6 printer driver.
If you have a problem printing from older software using
the PCL6 driver,remove it and install the PCL5e driver.
<4> Proceed to step 5).
2) Search for the printer driver by clicking [Other Locations...] button.
3) Insert the SHARP Software CD-ROM into the CD-ROM drive, type
R:\English\WinXX and click the [OK] button.
4) After Windows finds the printer driver, click the [Finish] button to
continue the installation.
Note: In this step the PCL6 printer driver is installed automat-
ically. If you want to install the PCL5e printer driver, refer
to “Installing onto Windows 95/98 without Using the Plug &
Play Function”.
5) Set the printer name.
<1> If you want to change the printer name, enter a new name
in the space provided.
<2> If the program displays, “Do you want your Windows-based
programs to use this printer as the default printer?”, check
“Yes”.
<3> Click the [Next] button.
6) Print a test page by clicking the [Finish] button.
Note: If you check “No” and click the [Finish] button, the printer
does not print a test page after the installation.
● The printer driver installation begins.
● If the “Insert Disk” window appears, perform the following steps:
<1> Click the [OK] button.
<2> When the “Copying Files” window appears, type
R:\English\WinXX and click the [OK] button.
7) When the test page is printed properly, click the [Yes] button.
● The printer is ready for printing.
B. Installing onto Windows 98
This printer is compatible with plug & play. If your computer is incom-
patible with plug & play or if you want to use this printer as a network
printer, refer to “Installing onto Windows 95/98 without Using the Plug
& Play Function”.
1) Turn the computer on and start Windows 98.
● The  “Add New Hardware Wizard” window appears automat-
ically, click the [Next] button.
Note: If the “Add New Hardware Wizard” window does not ap-
pear in this step, refer to “Installing onto Windows 95/98
without Using the Plug& Play Function”.
2) Display a list of all the printer drivers by checking “Display a list
of all the drivers in a specific location, ...” and clicking the [Next]
button.
DM-2000
5  –  4

Download Sharp DM-2000 (serv.man5) Service Manual (Repair Manual)

Here you can view online or download Sharp DM-2000 (serv.man5) Service Manual in pdf. This Service Manual can help you recover, restore, fix, disassemble and repair Sharp DM-2000 (serv.man5) Copying Equipment. Information contained in Sharp DM-2000 (serv.man5) service manual (repair manual) typically includes:

  • Disassembly, troubleshooting, programming, maintenance, remote, adjustment, installation and setup instructions.
  • Schematics, wiring and block diagrams.
  • Printed wiring boards (PWB) and printed circuit boards (PCB).
  • Parts list (bill of materials).