DOWNLOAD Sharp DM-2000 (serv.man12) Service Manual ↓ Size: 216.41 KB | Pages: 18 in PDF or view online for FREE

Model
DM-2000 (serv.man12)
Pages
18
Size
216.41 KB
Type
PDF
Document
User Manual / Operation Manual
Brand
Device
Copying Equipment / DM2000-Operation Manual Part3
File
dm-2000-sm12.pdf
Date

Sharp DM-2000 (serv.man12) User Manual / Operation Manual ▷ View online

42
GENERAL
 INFORMA
TION
User programs
USER PROGRAMS
Program No. 14: Number of copies per account
Program No. 14 is used to display the total number of copies made against
each account number. When program No. 14 is entered, an account number
will appear in the copy quantity display.
If no account number has been registered, “14E” will appear in the copy
quantity display. Press the 
 key. The copier will return to step 2 on page
38.
1.
Use the copy ratio display (
) key to select the account
number.
Use the 
 key to advance through the account numbers.
2.
Press and hold down the 0 key.
The number of copies made against the specified account number will
be displayed. The two higher digits and the three lower digits will
appear alternately while the 0 key is pressed.
Example: 1,234 copies
The upper limit for the number of copies is 49,999. If the number of
copies made reaches 50,000, the number will be reset to 0 and counting
will start again from 0.
3.
Repeat steps 1 and 2 for other account numbers.
4.
To continue with other user programs, press the 
 key
and select another program number. To exit the user
program mode, press the light (
) key.
43
GENERAL
 INFORMA
TION
USER PROGRAMS
User programs
Program No. 15: Resetting account
Program No. 15 is used to reset all accounts or to reset any desired individual
account. When program No. 15 is entered, “0” will blink on the right side of
the copy quantity display.
If no account number has been registered, “15E” will appear in the copy
quantity display. Press the 
 key. The copier will return to step 2 on page
38.
1.
To reset an individual account, press the 0 key.
To reset all accounts, press key 1.
2.
Press the START key.
If you have pressed the 0 key in step 1, an account number will appear
in the copy quantity display. Proceed to step 3.
If you have pressed key 1, the number of copies against all account
numbers will be reset. Proceed to step 5.
3.
Use the copy ratio display (
) key to select the account
number to be reset.
Use the 
 key to advance through the account numbers.
4.
Press the START key.
The number of copies against the specified account number will be
reset.
5.
To continue with other user programs, enter another
program number. To exit the user program mode, press
the light (
) key.
44
GENERAL
 INFORMA
TION
POWER SAVE MODES
The copier has two power save modes to reduce overall power consumption
thereby reducing the cost of operation. In addition, these modes conserve
natural resources and help reduce environmental pollution. The two power
save modes are preheat mode and auto power shut-off mode.
User programs
The preheat activation time and the auto power shut-off time have been
preset at the factory to 90 sec. for preheat mode and 30 min. for auto power
shut-off mode. These times can be changed using user programs. It is
suggested that you set appropriate times according to the actual usage of
the copier. See page 37.
Preheat mode
When the copier enters the preheat mode, the POWER SAVE indicator will
light up and other indicators will remain on or off as before. In this condition,
the fuser in the copier is maintained at a lower heat level, thereby saving
power. The preheat level is, however, high enough to allow the copier to
come to a ready condition or begin copying within 10 seconds after any key
input or copier operation such as paper tray operation is performed.
Auto power shut-off mode
When the copier enters the auto power shut-off mode, the POWER SAVE
indicator will light up and all other indicators will go out. The auto power
shut-off mode saves more power but requires a longer time to warm up before
copying can begin.
Power save modes
45
GENERAL
 INFORMA
TION
Setting the power save modes
The time that elapses before the copier enters a power save mode after any
operation is made can be set manually. This time is set with user program No.
2 for the preheat mode and user program No. 3 for the auto power shut-off
mode. For these settings, see page 38.
The copier will enter the preheat mode first and then the auto power shut-
off mode after a preset time has elapsed when no copier operation has been
made.
If conflicting settings are made with user programs No. 3 and No. 5, the
last program set will have priority.
Copying from the preheat mode
Make desired copier selections and press the START
key using the normal copying procedure.
When any key input is made or any other copier operation is made, the
POWER SAVE indicator will start to blink.
When the START key is pressed, the START key indicator will go out
and copying will start within 10 seconds. The POWER SAVE indicator
will go out when copying starts.
Copying from the auto power shut-off mode
1
Press the START key.
The copier will exit the auto power shut-off mode and the POWER
SAVE indicator will start to blink.
2
Make desired copier selections and press the START
key using the normal copying procedure.
It will take approximately 35 seconds for the copier to start copying.
However, you can make desired settings and press the START key
during warm-up. Copying will start after warm-up is finished.
Power save modes
POWER SAVE MODES
Page of 18
Display

Click on the first or last page to see other DM-2000 (serv.man12) service manuals if exist.