DM-2000 (serv.man12). DM2000-Operation Manual Part3 — Sharp Copying Equipment User Guide / Operation Manual

Model
DM-2000 (serv.man12)
Pages
18
Size
216.41 KB
Type
PDF
Document
User Guide / Operation Manual
Brand
Device
Copying Equipment / DM2000-Operation Manual Part3
File
dm-2000-sm12.pdf
Date

View Sharp DM-2000 (serv.man12) User Guide / Operation Manual online

37
GENERAL
 INFORMA
TION
Program No.
Program name
Description
1
Auto clear time
Sets the auto clear time. The copier returns to the initial settings
when the auto clear time elapses after the last copy is made.
2
Preheat mode
Sets the time that elapses before the copier enters the preheat
mode after any operation is made. See page 44.
3
Auto power shut-off
Sets the time that elapses before the copier enters the auto power
timer
shut-off mode after any operation is made. See page 44.
4
Stream feeding
Enables or disables  the stream feeding mode when an optional single pass
mode*
feeder (SPF) is installed. See page 58.
5
Auto power shut-off
Enables or disables the auto power shut-off mode. See page 44.
setting
6
Border line for 2 in 1 or
Enables or disables the border line which is printed in 2 in 1 or 4 in 1
4 in 1*
copying when an optional electronic sorting kit and an optional SPF are
installed. See page 63.
7
Rotation copy*
Enables or disables rotation of original images. See page 60.
8
Auto paper select mode
Enables or disables the auto paper selection. See page 14.
9
Auto tray switching
Enables or disables the automatic tray switching which occurs when paper
in a tray runs out. (This switching cannot switch to the bypass tray.)
10
Auditing mode
Enables or disables the auditing mode, which controls access to
copier. See page 13.
11
Account number entry
Registers accounts for auditing mode.
12
Account number
Changes account numbers for auditing mode.
change
13
Account number
Deletes accounts for auditing mode.
deletion
14
Number of copies
Displays the total number of copies made against account numbers.
per account
15
Resetting account
Resets all audit accounts or resets any desired individual account.
16
Erase width adjustment* Sets the amount of the edge erase and centre erase areas. See page 65.
17
Layout in 2 in 1 copy*
Selects a pattern for 2 in 1 copying. See page 63.
18
Layout in 4 in 1 copy*
Selects a pattern for 4 in 1 copying. See page 63.
19
Offset of paper output
Enables or disables the offset function of the paper output tray. The offset
tray
function can be specified respectively for the upper and lower areas
separated by an optional job separator tray kit. See page 61.
* These programs do not affect the copier functions unless certain optional equipment is installed.
User programs
USER PROGRAMS
The user programs allow the parameters of certain functions to be set,
changed, or cancelled as desired.
List of user programs
This copier has the following user programs.
38
GENERAL
 INFORMA
TION
Setting the user programs
1
Press and hold the light (
) key for more than 5 seconds
until all the alarm indicators (
, and 
)
blink and “– –” appears in the copy quantity display.
2
Enter a program number using the numeric keys.
The selected program number will blink in the copy quantity display.
If a mistake is made in steps 2 to 4, press the CLEAR (
) key. The
copier will return to step 2.
The program numbers are shown in the table below.
For example, to change the setting of the auto power shut-off timer,
press key 3.
Program name
Program No.
Auto clear time
1
Preheat mode
2
Auto power shut-off timer
3
Stream feeding mode
4
Auto power shut-off setting
5
Border line for 2 in 1 or 4 in 1
6
Rotation copy
7
Auto paper select mode
8
Auto tray switching
9
Auditing mode
10
Account number entry
11
Account number change
12
Account number deletion
13
Number of copies per account
14
Resetting account
15
Erase width adjustment
16
Layout in 2 in 1 copy
17
Layout in 4 in 1 copy
18
Offset of paper output tray
19
3
Press the START key.
For programs 1 to 9 and 16 to 19, the entered program number will be
steadily lit on the left side of the copy quantity display and the currently
selected parameter number for the program will blink on the right side.
For programs 10 to 15 (programs for auditing accounts), the display
varies with the program number. See page 40 for setting programs 10
to 15.
USER PROGRAMS
User programs
For operation of these programs after
step 3, see page 40.
39
GENERAL
 INFORMA
TION
USER PROGRAMS
4
Select the desired parameter using the numeric keys.
The entered parameter number will blink on the right side of the copy
quantity display.
The parameters are shown in the table below.
For example, to change the setting of the auto power shut-off timer to
60 min., press key 2.
5
Press the START key.
The right-hand number in the copy quantity display will be steadily lit
and the entered value will be stored.
6
To continue with other user programs, press the 
 key
and then repeat steps 2 to 5. To exit the user program
mode, press the light (
) key.
All the alarm indicators will go out.
User programs
Program name
Parameters
Auto clear time
0 e OFF
1 e 30 sec.
* 2 e 60 sec.
3 e 90 sec.
4 e 120 sec.
5 e 10 sec.
Preheat mode
0 e OFF
1 e 30 sec.
2 e 60 sec.
* 3 e 90 sec.
4 e 120 sec.
Auto power shut-off timer
* 1 e 30 min.
2 e 60 min.
3 e 90 min.
4 e 120 min.
5 e 240 min.
Stream feeding mode
* 0 e OFF
1 e ON
Auto power shut-off setting
0 e OFF
* 1 e ON
Border line for 2 in 1 or 4 in 1 * 0 e OFF
1 e ON
Rotation copy
0 e OFF
* 1 e ON
Auto paper select mode
0 e OFF
* 1 e ON
Auto tray switching
0 e OFF
* 1 e ON
Erase width adjustment
0 e 0 mm
1 e 5 mm
* 2 e 10 mm
3 e 15 mm
4 e 20 mm
Layout in 2 in 1 copy
* 1 e Pattern 1
2 e Pattern 2
Layout in 4 in 1 copy
* 1 e Pattern 1
2 e Pattern 2
3 e Pattern 3
4 e Pattern 4
Offset of paper output tray
0 e Upper OFF, lower OFF
* 1e Upper ON, lower ON
2 e Upper ON, lower OFF
3 e Upper OFF, lower ON
Factory default settings are indicated with an asterisk (*). For layout in 2 in 1 copy and 4 in 1 copy, see page 63.
If you select “0” (OFF) in a program, the corresponding
function will be disabled.
40
GENERAL
 INFORMA
TION
USER PROGRAMS
User programs
Settings for auditing accounts
Setting of user programs No. 10 to 15 varies with the program number. For
settings of all programs, first follow steps 1 to 3 in “Setting the user
programs” on page 38 to select a program. (1. Press the light (
) key for
more than 5 seconds. 2. Enter a program number (10 to 15) using the numeric
keys. 3. Press the START key.) Then follow the appropriate instructions for
the program.
Program No. 10: Auditing mode
If the auditing mode is enabled, copying is limited to operators with an
assigned 3-digit account number. A maximum of 20, 3-digit account numbers
can be assigned. Use program No. 11 to register account numbers.
When program No. 10 is entered, the current setting (0: OFF, 1:ON) will blink
on the right side of the copy quantity display.
1.
Select the desired setting using the numeric keys.
0:
OFF
1:
ON
2.
Press the START key.
The setting will be stored.
3.
To continue with other user programs, press the 
 key
and enter another program number. To exit the user
program mode, press the light (
) key.
1.
Enter a 3-digit account number using the numeric keys.
Any 3-digit number except “000” can be registered as an account
number.
2.
Press the START key.
If a number that is already registered or “000” is entered, the number
will blink in the copy quantity display.
3.
Repeat steps 1 and 2 for other account numbers.
4.
To continue with other user programs, press the 
 key
and enter another program number. To exit the user
program mode, press the light (
) key.
Program No. 11: Account number entry
Program No. 11 is used to register accounts. When program No. 11 is entered,
–––
” will blink in the copy quantity display.
If the number of accounts has reached the upper limit (20), “11E” will
appear in the copy quantity display. Press the 
 key. The copier will
return to step 2 on page 38.
Page of 18
Display

Download Sharp DM-2000 (serv.man12) User Guide / Operation Manual

Here you can view online or download Sharp DM-2000 (serv.man12) User Guide / Operation Manual in pdf. This User Guide / Operation Manual can help you recover, restore, fix, disassemble and repair Sharp DM-2000 (serv.man12) Copying Equipment. Information contained in Sharp DM-2000 (serv.man12) service manual (repair manual) typically includes:

  • Disassembly, troubleshooting, programming, maintenance, remote, adjustment, installation and setup instructions.
  • Schematics, wiring and block diagrams.
  • Printed wiring boards (PWB) and printed circuit boards (PCB).
  • Parts list (bill of materials).