Sharp AR-PE3 (serv.man12) User Manual / Operation Manual ▷ View online
4
4-9
Network Setup options
Network Setup options
When you perform Network Setup, you configure the Fiery X3e to receive print jobs
over the network systems that are used at your site.
over the network systems that are used at your site.
If the Fiery X3e is configured to enable more than one protocol, it automatically
switches to the correct protocol when it receives a print job.
switches to the correct protocol when it receives a print job.
In the Setup menu, choose Network Setup, where you specify network addresses and
names to be used by workstations, servers, and the Fiery X3e when they communicate
with each other.
names to be used by workstations, servers, and the Fiery X3e when they communicate
with each other.
The Network Setup menu includes three submenus that allow you to choose port
types, protocols, and network services. You must perform Port Setup and enable at
least one port.
types, protocols, and network services. You must perform Port Setup and enable at
least one port.
For each item you enable, you are prompted to enter settings for that item. Default
values, where applicable, appear in this manual with square brackets.
values, where applicable, appear in this manual with square brackets.
Display and select options only for the network systems that are currently used at your
site. If your network requirements change, you can change Network Setup at any time.
site. If your network requirements change, you can change Network Setup at any time.
4
4-10
Performing Setup from the Control Panel
The available network types, and the Setup areas that pertain to them, are summarized
in the following table.
in the following table.
T
O
ACCESS
N
ETWORK
S
ETUP
OPTIONS
1.
Confirm that the network cable is connected to the Fiery X3e.
During Network Setup, the Fiery X3e queries the network for zones, servers, and
server-based queues. If you perform Network Setup without a connected and
functioning network, default settings are used that may not meet your needs.
server-based queues. If you perform Network Setup without a connected and
functioning network, default settings are used that may not meet your needs.
2.
Choose Network Setup from the main Setup menu.
3.
Choose Port Setup from the Network Setup menu.
4.
To use Ethernet, choose Ethernet Setup from the Port Setup menu, and enter the
appropriate settings.
appropriate settings.
For this Network or
Connection Type
Use this
Port Setup
Use this Protocol Setup
Use this Service Setup
AppleTalk over Ethernet
Ethernet Setup
AppleTalk Setup
AppleTalk printing (PAP) is
enabled automatically
enabled automatically
TCP/IP over Ethernet
Ethernet Setup
TCP/IP Setup: Ethernet Setup
LPD Setup
Web Services Setup
Windows Setup
Port 9100 Setup
IPP Setup
(Windows 9x/Me/2000/XP)
Web Services Setup
Windows Setup
Port 9100 Setup
IPP Setup
(Windows 9x/Me/2000/XP)
IPX/SPX over Ethernet
Ethernet Setup
IPX/SPX Setup
PServer Setup (NDS, Bindery,
or both)
or both)
4
4-11
Network Setup options
5.
When you have finished entering port settings, choose Exit Port Setup, and then
choose Protocol Setup.
choose Protocol Setup.
6.
Enter the appropriate settings for the protocol or protocols you will use.
7.
When you have finished entering protocol settings, choose Exit Protocol Setup, and
then choose Service Setup.
then choose Service Setup.
8.
Enter the appropriate settings for the services you will use.
The options are described in detail in the following pages.
T
O
EXIT
N
ETWORK
S
ETUP
1.
When you have finished entering service settings, choose Exit Network Setup.
2.
Choose Yes when prompted to save changes.
3.
From the main Setup menu, choose another Setup or choose Exit Setup.
Port Setup options
Network Setup
Port Setup
Ethernet Setup
Enable Ethernet
Yes/No [Yes]
Yes/No [Yes]
Select Yes if you have Ethernet cabling connected to the Fiery X3e.
Ethernet Speed
Auto Detect/100 Mbps/10 Mbps [Auto Detect]
Auto Detect/100 Mbps/10 Mbps [Auto Detect]
Select Auto Detect if your network environment is mixed or if you do not know the
network speed. If you know the speed of the network to which the Fiery X3e is
attached (10 Mbps or 100 Mbps), select it.
network speed. If you know the speed of the network to which the Fiery X3e is
attached (10 Mbps or 100 Mbps), select it.
4
4-12
Performing Setup from the Control Panel
Protocol Setup options
AppleTalk Zone
List of zones
List of zones
The Fiery X3e searches the network for AppleTalk zones in your network segment.
Scroll through the list to select the AppleTalk zone in which you want the Fiery X3e to
appear. If your segment has only one zone, the Fiery X3e is assigned to that
zone
Scroll through the list to select the AppleTalk zone in which you want the Fiery X3e to
appear. If your segment has only one zone, the Fiery X3e is assigned to that
zone
automatically.
The message “No AppleTalk zone found” may mean your network has no zones, or the
network cable is not connected (see
network cable is not connected (see
Appendix A
). Choose Set to dismiss the message.
TCP/IP Setup options
When you set an IP address, subnet mask, or gateway address for the Fiery X3e during
Setup, you can allow the Fiery X3e to get these addresses automatically from a DHCP
or BOOTP server. First, turn on or restart the Fiery X3e and allow it to reach Idle.
Make sure the DHCP or BOOTP server is running, and then perform
Fiery X3e
Setup, you can allow the Fiery X3e to get these addresses automatically from a DHCP
or BOOTP server. First, turn on or restart the Fiery X3e and allow it to reach Idle.
Make sure the DHCP or BOOTP server is running, and then perform
Fiery X3e
Setup.
To configure the Fiery X3e, choose each protocol and enter the settings for that
protocol. You can enable AppleTalk, TCP/IP, and IPX/SPX communication
simultaneously.
protocol. You can enable AppleTalk, TCP/IP, and IPX/SPX communication
simultaneously.
Network Setup
Protocol Setup
AppleTalk Setup
Enable AppleTalk
Yes/No [Yes]
Yes/No [Yes]
Select Yes if you have an AppleTalk network connected to the Fiery X3e. This
setting enables the Fiery X3e to communicate over AppleTalk networks.
setting enables the Fiery X3e to communicate over AppleTalk networks.
To configure the Fiery X3e for TCP/IP, choose TCP/IP Setup.
Choose Ethernet Setup and enter the appropriate settings. Choose each network
type you use (Ethernet) and enter the appropriate settings.
type you use (Ethernet) and enter the appropriate settings.
Click on the first or last page to see other AR-PE3 (serv.man12) service manuals if exist.