DOWNLOAD Sharp AR-M550 (serv.man23) Service Manual ↓ Size: 7.48 MB | Pages: 56 in PDF or view online for FREE

Model
AR-M550 (serv.man23)
Pages
56
Size
7.48 MB
Type
PDF
Document
Service Manual
Brand
Device
Copying Equipment / ARM550 620 Installation Manual
File
ar-m550-sm23.pdf
Date

Sharp AR-M550 (serv.man23) Service Manual ▷ View online

AR-M550/M620  INSTALLATION MANUAL  (AR-F15/F16)  4 - 5
2) Attach the earth plate with the fixing screws H (2 pcs.) to the left
lower section of the main unit.
In this case, attach so that the R mark on the earth plate faces up.
3) Pull out the lock release lever on the left side of the main unit, and
open the left door.
4) Remove the paper exit cover on the upper side of the left door.
5) Close the left door.
6) Install the connection plate to the main unit with the fixing screws I
(2 pcs.).
(3) Plate and connection plate installation
1) Install the plate to the finisher as shown in the figure, and fix it with
the fixing screw G (1 pc).
2) Install the rail and the finisher with two screws G (M4 x 6).
(4) Caster adjustment
A. Bring the finisher closer to the main unit and check that the
guide pin of the main unit enters into the connection hole in the
finisher smoothly.
B. At that time, check that the center of the guide pin is in the cen-
ter of the scale marked on the side of the connection hole, and
the pin direction coincides with the hole direction.
C. If the guide pin is not in the center, or if the guide pin does not
enter smoothly, adjust as follows:
F
R
2
1
AR-M550/M620  INSTALLATION MANUAL  (AR-F15/F16)  4 - 6
1) Remove the fixing screw of base cover (2 positions) in the front and
the back of the finisher, and remove the base cover.
2) Remove the fixing screws (2 pcs.) of the rear cover on the rear of
the finisher, and remove the rear cover.
3) Only for the AR-F15, remove the front cabinet lower fixing screws
(2 pcs.).
4) Open the front cabinet lower, and loosen the fixing screws (2 pcs
for each) of four casters.
5) Remove the spanner stored inside of the front cabinet upper, and
close the front cabinet upper.
6) Turn the bolt with the removed spanner so that the guide pin is in
the specified range of the scale.
(At that time, lift the finisher a little, and the bolt can be turned man-
ually.)
7) After completion of the adjustment, tighten the caster fixing screws
(8 pcs.) and close the front cabinet lower.
8) Check to insure that the intervals at the upper and the lower sides
of the main unit and the finisher are even.
9) Attach the foot covers in front and at the back of the finisher and the
rear cover on the rear side, and tighten all the fixing screws.
AR-M550/M620  INSTALLATION MANUAL  (AR-F15/F16)  4 - 7
(5) Attach the staple position label.
Attach the staple position label as shown in the figure.
The label attachment position shown above is based on the corner
of the cabinet.
(6) Connect the finisher connector.
A. Remove the connector cover fixing screw for connection of the fin-
isher joint harness connector, and remove the connector cover.
B. Connect the finisher relay harness connector to the main unit con-
nector, and tighten the screw on the connector to fix.
(7) Turn ON the main power switch.
1) Insert the power plug of the main unit to the outlet.
2) Open the front cabinet, and open the power cover.
3) Turn ON the main power switch, close the power cover, and close
the front cabinet.
4) Turn ON the power switch on the right side of the main unit.
0.5mm
40mm
2mm
2mm
1
2
3
AR-M550/M620  INSTALLATION MANUAL  (AR-PN4)  5 - 1
[5] AR-PN4 UNPACKING AND INSTALLATION
1. Unpacking
(1) Removal of the main unit
(2) Removal of the fixing member
Packaged parts (accessories)
2. Installation
(1) Turn off the power of the main unit.
1) Turn OFF the power switch on the right side of the main unit.
2) Open the front cabinet, and turn OFF the main power switch.
3) Disconnect the power plug from the power outlet.
Punch position label
2 pcs.
Page of 56
Display

Click on the first or last page to see other AR-M550 (serv.man23) service manuals if exist.