DOWNLOAD Sharp AR-M550 (serv.man23) Service Manual ↓ Size: 7.48 MB | Pages: 56 in PDF or view online for FREE

: Jan. 9 2004

AR-M550/M620  INSTALLATION MANUAL  (AR-CF2)  3 - 5

3) Hold the lower section of the front cabinet and the grip of the rear

cabinet as shown in the figure, tilt the inserter a little so that the indi-
cation hole in the inserter support section is fit with the metal fixture
of the finisher connecting plate installing section, and install it.

∗

At that time,  check that the finisher lock lever is engaged on the
inserter groove securely.

4) Tighten the fixing screw of the inserter lock to fix the inserter and

the finisher.

5) Check that the finisher lock lever is engaged on the inserter groove

securely.

When the finisher and the inserter differ in the height, perform the fol-
lowing height adjustment, and insert the inserter.

1) Set all the finisher height adjustment screws (4 positions) to the

center positions.

2) Insert the inserter to the finisher. (Refer to the procedure (7) in this

section.)

1) Pull out the extension guide of the inserter paper feed tray until it

stops.

2) Tighten the fixing screws F (2 pcs.) on the back side of the paper

feed tray.

: Jan. 9 2004

AR-M550/M620  INSTALLATION MANUAL  (AR-CF2)  3 - 6

Remark: The plate and the connection plate are common to the fin-

isher. Please reuse rail and connector plate for inserter.

1) Connect the finisher relay harness connector to the inserter con-

nector, and tighten the connector screw to fix it.

2) Fix the finisher relay harness to the rear side of the inserter with two

clamps.

3) Connect the inserter relay harness connector to the main unit con-

nector, and tighten the connector screw to fix the connector.

1) Bring the inserter closer to the main unit.

2) Check that the main unit positioning pin enters smoothly into the

center of the inserter positioning guide.

1) Install the connection plate to the inserter with the fixing screws G

(2 pieces.).

1

2

AR-M550/M620  INSTALLATION MANUAL  (AR-CF2)  3 - 7

1) Loosen the adjustment section fixing screws (2 pcs.) on the rear

side.

2) Turn and adjust the rear side height adjustment bolt so that the cen-

ter height of the positioning pin comes at the center of the position-
ing guide.

3) Tighten two fixing screws of the rear side adjustment section.

4) Loosen the front side adjustment section fixing screws (2 pcs.)

5) Turn and adjust the front side height adjustment bolt so that it is at

the same position with the rear side adjustment section fixing
screw.

6) Tighten two fixing screws of the front side adjustment section.

1) Check the height of the inserter front cabinet and the finisher front

cabinet.

2) Check the height of the inserter rear cabinet and the finisher rear

cabinet.

Go to procedure 13.

A. Adjust the height of the front side.

1) Open the finisher front door upper, remove the spanner stored in

the upper section of the front door, and close the front door upper.

2) Open the front door of the inserter, open the front door lower of the

finisher

F

R

AR-M550/M620  INSTALLATION MANUAL  (AR-CF2)  3 - 8

3) Loosen the fixing screws (2 pcs.) of the adjustment section of the

base.

4) Use the spanner removed in step 1) to adjust the height adjustment

bolt so that the upper cabinet is of the same height.

5) Tighten the adjustment section fixing screws (2 pcs.).

6) Close the finisher front door lower, and close the inserter front door.

B. Adjust the rear side height.

1) Remove two screws which are fixing the base cover attached to the

finisher rear side base section, and remove the base cover.

2) Loosen the adjustment section fixing screws (2 pcs.).

3) Use the spanner and adjust the height adjustment bolt so that the

height of the rear side cabinet top surface is of the same height.

4) Tighten the adjustment section fixing screws (2 pcs.).

5) Install the base cover.

1) Push the inserter into the main unit.

2) Check the upper and the lower clearances between the main unit

and the inserter cabinet.