DOWNLOAD Sharp AR-M550 (serv.man15) Service Manual ↓ Size: 905.4 KB | Pages: 98 in PDF or view online for FREE

Model
AR-M550 (serv.man15)
Pages
98
Size
905.4 KB
Type
PDF
Document
Service Manual
Brand
Device
Copying Equipment / (8) Simulation
File
ar-m550-sm15.pdf
Date

Sharp AR-M550 (serv.man15) Service Manual ▷ View online

AR-M550/M620  SIMULATION  8 - 10
22
1
Used to check the print count value 
in each section and each operation 
mode. (Used to check the 
maintenance timing.)
Adjustment/Setup/
Operation data output/
Check (Display/Print)
Counter
2
Used to check the total numbers of 
misfeed and troubles. (When the 
number of misfeed is considerably 
great, it is judged as necessary for 
repair. The misfeed rate is obtained 
by dividing this count value with the 
total counter value.)
Adjustment/Setup/
Operation data output/
Check (Display/Print)
Trouble
3
Used to check misfeed positions and 
the misfeed count of each position. 
(If the misfeed count is considerably 
great, it may be judged as necessary 
to repair.)
Adjustment/Setup/
Operation data output/
Check (Display/Print)
Sections other 
than SPF/DSPF 
section
Trouble
Misfeed
4
Used to check the trouble (self diag) 
history.
Adjustment/Setup/
Operation data output/
Check (Display/Print)
Trouble
5
Used to check the ROM version of 
each unit (section).
Other
Software
6
Used to output the list of the setting 
and adjustment data (simulations, 
FAX soft switch, counters).
Adjustment/Setup/
Operation data output/
Check (Display/Print)
Data
Adjust/Setting 
data
7
Used to display the key operator 
code. (This simulation is used when 
the customer forgets the key 
operator code.)
Adjustment/Setup/
Operation data output/
Check (Display/Print)
Data
User data
8
Used to check the number of use of 
the finisher, the SPF, and the scan 
(reading) unit.
Adjustment/Setup/
Operation data output/
Check (Display/Print)
Optical (Image 
scanning)
Finisher
Counter
9
Used to check the number of use 
(print quantity) of each paper feed 
section.
Adjustment/Setup/
Operation data output/
Check (Display/Print)
Paper feed, ADU
Counter
10
Used to check the system 
configuration (option, internal 
hardware). 
Adjustment/Setup/
Operation data output/
Check (Display/Print)
Specifications
Options
11
Used to check the use frequency 
(send/receive) of FAX. (Only when 
FAX is installed)
Adjustment/Setup/
Operation data output/
Check (Display/Print)
FAX
Data
12
Used to check the SPF misfeed 
positions and the number of misfeed 
at each position. (When the number 
of misfeed is considerably great, it 
can be judged as necessary for 
repair.)
Adjustment/Setup/
Operation data output/
Check (Display/Print)
DSPF
Trouble
13
Used to check the operating time of 
the process section (OPC drum, DV 
unit, toner bottle).
Adjustment/Setup/
Operation data output/
Check (Display/Print)
Counter
19
Used to check the values of the 
counters related to the scan mode 
and the internet FAX mode.
Adjustment/Setup/
Operation data output/
Check (Display/Print)
Scanner
Counter
23
2
Used to check the trouble history of 
paper jam and misfeed. (If the 
number of misfeed and troubles is 
considerably great, it may be judged 
as necessary to repair.)
Adjustment/Setup/
Operation data output/
Check (Display/Print)
Trouble
80
Used to check the operations of the 
sensors and detectors in the paper 
feed and transport section.
Operation test/Check
Paper feed, paper 
transport
Operation
Code
Function (Purpose)
Purpose
Section
Item
Main
Sub
AR-M550/M620  SIMULATION  8 - 11
24
1
Used to clear the misfeed counter, 
the misfeed history, the trouble 
counter, and the trouble history. (The 
counters are cleared after 
completion of maintenance.)
Data clear
Counter
2
Used to clear the number of use (the 
number of prints) of each paper feed 
section.
Data clear
Paper feed
Counter
3
Used to clear the number of use of 
the finisher, SPF, and the scan 
(reading) unit.
Data clear
Counter
4
Used to reset the maintenance 
counter.
Data clear
Counter
5
Used to reset the developer counter. 
(The developer counter of the DV 
unit which is installed is reset.)
Data clear
Counter
Developer
6
Used to reset the copy counter.
Data clear
Counter
Copy
7
Used to clear the OPC drum counter. 
(Perform this simulation when the 
OPC drum is replaced.)
Data clear
Image process 
(Photoconductor/
Developing/
Transfer/Cleaning)
Counter
Photo 
conductor
9
Used clear the printer mode print 
counter and the self print mode print 
counter.
Data clear
Printer
Counter
10
Used to clear the FAX counter. (Only 
when FAX is installed)
Data clear
FAX
Counter
11
Used to reset the OPC drum rotation 
time, and the DV unit rotation time 
counter. The developer counter in 
the DV unit installed is reset.
Data clear
Image process 
(Photoconductor/
Developing/
Transfer/Cleaning)
Counter
Developer
15
Used to clear the counters related to 
the scan mode and the internet FAX 
mode.
Data clear
Counter
25
1
Used to check the operations of the 
developing section (toner 
concentration, humidity and toner 
concentration sensor, humidity 
sensor). (The toner concentration 
sensor output can be monitored.)
Operation test/Check
Process 
(Developing 
section)
Operation
2
Used to make the initial setting of 
toner concentration when replacing 
developer.
Setting
Image process 
(Photoconductor/
Developing/
Transfer/Cleaning)
26
2
Used to set the paper size of the 
large capacity tray (LCC) and the 
paper feed tray 2. (When the paper 
size is changed, this simulation must 
be executed to change the paper 
size in software.)
Setting
Paper feed
Setting
3
Used to set the specifications of the 
auditor. Setting must be made 
according to the auditor use 
conditions.
Setting
Auditor
Specifications
5
Used to set the count mode of the 
total counter and the maintenance 
counter.
Setting
Specifications
Counter
6
Used to set the specifications 
(paper, fixed magnification ratio, 
etc.) of the destination.
Setting
Specifications
Destination
10
Used to set the network scanner trial 
mode.
Setting
Operation
Code
Function (Purpose)
Purpose
Section
Item
Main
Sub
AR-M550/M620  SIMULATION  8 - 12
26
18
Used to set YES/NO of toner save 
operation. (This function is valid only 
in Japan and UK versions. (Depends 
on the destination setting of SIM26-
6.) For the other destinations, the 
same setting can be made by the 
user program P22.)
Setting
Specifications
Operation 
mode
30
Used to set the operation mode 
conforming to the CE mark (Europe 
safety standards). (Conforming to 
soft start when driving the fusing 
heater lamp.)
Setting
Specifications
Operation 
mode 
(Common)
35
Used to set whether the same 
continuous troubles are displayed as 
one trouble or the series of troubles 
with SIM 22-4 when the same 
troubles occur continuously.
Setting
Specifications
38
Used to set CONTINUE/STOP of 
printing when developer 
replacement timing (life) is over and 
the count value reaches 110% of 
replacement timing (life). 
Setting
Other
Specifications
41
Used to set YES/NO of the 
automatic magnification ratio 
selection (AMS) in the pamphlet 
mode.
Setting
Specifications
Operation 
mode 
(Common)
50
Black-White reverse YES/NO setting
Setting
Specifications
Operation
52
Used to set whether non-print paper 
(insertion paper, cover paper) (blank 
image print paper) is counted up or 
not.
Setting
Paper transport 
(Discharge/
Switchback/
Transport)
Specifications
Operation 
mode
68
Used to set ENABLE/DISABLE of 
the CA key cancel function of print 
stop.
Setting
Specifications
Operation
27
1
Used to set the specifications for 
operations in case of communication 
trouble between the host computer 
and MODEM (machine side). (When 
communication trouble occurs 
between the host computer MODEM 
and the machine, the self diag 
display (U7-00) is printed and setting 
for inhibition of print or not is made.)
Setting
Communication 
unit (TEL/LIU/
MODEM etc.)
Specifications
Operation 
mode
5
Used to enter the machine tag No. 
(This function allows to check the tag 
No. of the machine with the host 
computer.)
Setting
Communication 
unit (TEL/LIU/
MODEM etc.)
Specifications
Operation 
mode
30
1
Used to check the operation of 
sensors and detectors in other than 
the paper feed section and the 
operations of the related circuits.
Operation test/Check
Operation
2
Used to check the operation of 
sensors and detectors in the paper 
feed section and the related circuits.
Operation test/Check
Paper feed
Operation
40
1
Used to check the operation of the 
manual feed tray paper size detector 
and the related circuit. (The 
operation of the manual feed tray 
paper size detector can be 
monitored with the LCD display.)
Operation test/Check
Paper feed
Operation
2
Used to adjust the manual paper 
feed tray paper width detector 
detection level.
Adjustment
Paper feed
Operation
7
Used to enter the manual paper feed 
tray paper width adjustment value.
Adjustment/Setup
Paper feed
Operation
Code
Function (Purpose)
Purpose
Section
Item
Main
Sub
AR-M550/M620  SIMULATION  8 - 13
40
11
Used to check the multi-purpose tray 
width detection adjustment value.
Operation test/Check
Paper feed
Operation
12
Used to check the multi-purpose tray 
width detection adjustment value.
Adjustment/Setup
Paper feed
Operation
41
1
Used to check the operation of the 
document size sensor and the 
related circuit. (The operation of the 
document size sensor can be 
monitored with the LCD display.)
Operation test/Check
Other
Operation
2
Used to adjust the document size 
sensor sensing level.
Adjustment
Other
Operation
3
Used to check the operation of the 
document size sensor and the 
related circuit. (The document size 
sensor output level can be monitored 
with the LCD display.)
Operation test/Check
Other
Operation
43
1
Used to set the fusing temperature in 
each operation mode.
Setting
Fixing (Fusing)
Operation
3
Fusing roller RPM setting.
Setting (Adjustment)
Fixing (Fusing)
Operation
44
1
Used to set enable/disable of 
correction operations in the image 
forming (process) section.
Setting
Image process 
(Photoconductor/
Developing/
Transfer/Cleaning)
Operation
2
Used to perform the gain adjustment 
(image density sensor LED current 
adjustment) of the image density 
sensor and the gain adjustment 
(OPC drum marking sensor LED 
current adjustment) of the OPC drum 
marking sensor.
Adjustment
Image process 
(Photoconductor)
Operation
4
Used to set the target density level in 
the image density correction.
Setting
Image process 
(Photoconductor/
Developing)
Operation
5
Used to set the reference developing 
bias voltage, the reference main 
charger grid voltage, and the laser 
power in the image density 
correction.
Setting
Image process 
(Photoconductor/
Developing)
Operation
9
Used to check the data related to the 
image forming section correction 
(process correction) result (corrected 
main charger grid voltage, the 
developing bias voltage, and the 
laser power voltage in each print 
mode). (This simulation allows to 
check that correction is performed 
normally or not.)
Adjustment/Setup/
Operation data output/
Check (Display/Print)
Image process 
(Photoconductor/
Developing/
Transfer/Cleaning)
Data
Operation data 
(Machine 
condition)
12
Used to display sampling toner 
image patch density data in image 
density correction. (Used to check 
that the correction is performed 
normally or not.)
Adjustment/Setup/
Operation data output/
Check (Display)
Image process 
(Photoconductor/
Developing)
Operation
14
Used to check the output level of the 
temperature sensor and the humidity 
sensor.
Adjustment/Setup/
Operation data output/
Check (Display)
Image process 
(Photoconductor/
Developing)
Operation
16
Used to check the toner 
concentration control data.
Adjustment/Setup/
Operation data output/
Check (Display)
Image process 
(Developing)
Operation
Code
Function (Purpose)
Purpose
Section
Item
Main
Sub
Page of 98
Display

Click on the first or last page to see other AR-M550 (serv.man15) service manuals if exist.