Sharp AR-M550 (serv.man13) Service Manual ▷ View online
AR-M550/M620 DETAILS OF EACH SECTION 6 - 136
a-1. Resist roller front drive motor
1) Remove the resist roller unit. (See “2. Paper feed, paper transport,
duplex, and paper exit reverse sections” “(Vertical paper transport
section 2)”, “a. Resist roller unit”)
section 2)”, “a. Resist roller unit”)
2) Remove the flywheel. (See “b-1. OPC drum motor” in this section)
3) Remove the main motor. (See “a-1. Main motor” in this section)
4) Remove the main drive unit. (See “a-1. Main motor” in this section)
5)Remove the resist roller front drive motor.
a-2. Resist roller clutch
1) Remove the resist roller unit. (See “2. Paper feed, paper transport,
duplex, and paper exit reverse sections” “(Vertical paper transport
section 2)”, “a. Resist roller unit”)
section 2)”, “a. Resist roller unit”)
2) Remove the flywheel. ((See “b-1. OPC drum motor” in this section
(a. Drum drive unit))
3) Remove the main motor. (See “a-1. Main motor” in this section)
4) Remove the main drive unit. (See “a-1. Main motor” in this section)
5) Disconnect the connector, and remove the main drive frame.
6) Disconnect the connector, and remove the resist roller clutch unit.
∗
When installing, be sure to ensure that the projection of the plate is
engaged in the clutch rotation stopper.
engaged in the clutch rotation stopper.
7) Remove the bearing, the E-ring, and the set screw, and remove
the resist roller clutch.
a-1. Main motor
1) Remove the rear cabinet.
2) Disconnect the connector, and remove the main motor.
AR-M550/M620 DETAILS OF EACH SECTION 6 - 137
[Manual paper feed drive section]
(Replacement parts)
a. Manual paper feed drive unit
1) Remove the rear cabinet.
2) Disconnect the connector, the harness clamp, and the earth wire.
Remove the high voltage PWB unit.
3) Remove the plastic E-ring, the belt holding sheet, the belt, and the
pulley.
∗
When installing, be careful of the direction of the belt holding sheet.
4) Remove the harness clamp, and remove the manual paper feed
drive unit.
∗
Remove the screw which was indicated with the arrow mark.
[1/2 paper feed drive section]
(Replacement parts)
No.
Unit
Parts
a
Manual paper feed drive unit
a
No.
Unit
Parts
a
1/2 paper feed drive unit
1
Vertical paper transport motor
2
Paper feed tray 3/4 paper
transport clutch 2
transport clutch 2
3
Paper feed clutch (Paper feed
tray 1)
tray 1)
4
Horizontal paper transport
clutch
clutch
5
Paper feed clutch (Paper feed
tray 2)
tray 2)
6
Paper pickup solenoid (Paper
feed tray 1)
feed tray 1)
b
Other
1
Remove the paper tray lift-up
motor (paper feed tray 1)
motor (paper feed tray 1)
2
Paper tray lift-up motor (Paper
feed tray 2)
feed tray 2)
3
Paper pickup solenoid (Paper
feed tray 2)
feed tray 2)
b-1
a-2
a-3
a-1
a-5
a-4
b-2
b-3
a
a-6
AR-M550/M620 DETAILS OF EACH SECTION 6 - 138
a. 1/2 paper feed drive unit
1) Remove the main motor. (See “a-1. Main motor” in the “[Paper
feed/paper transport drive section]”)
2) Remove the high voltage PWB unit. (See “a. Manual paper feed
drive unit” in the “[Manual paper feed drive section]”)
3) Pull out the left door.
4) Disconnect the connector and remove the harness clamp. Remove
the DV fan unit.
5) Disconnect the connector and remove the harness holder.
6) Remove the plastic E-ring, the belt holding sheet, the belt, and the
pulley. Remove the joint plate.
∗
When installing, be careful of the direction of the belt holding sheet.
7) Remove the harness, and remove the drive joint plate.
∗
When installing, temporarily fix the 1/2 paper feed drive unit to the
main unit, and install the drive joint plate. Then tighten the screw of
the drive unit securely.
main unit, and install the drive joint plate. Then tighten the screw of
the drive unit securely.
8) Disconnect the connector and remove the harness clamp. Remove
the 1/2 paper feed drive unit.
∗
Remove the screw which was indicated with the arrow mark.
a-1. Vertical paper transport motor
1) Remove the 1/2 paper feed drive unit. (See “a. 1/2 paper feed drive
unit” in this section)
2) Loosen the screw to release the tension, and remove the belt.
3) Remove the parts.
AR-M550/M620 DETAILS OF EACH SECTION 6 - 139
4) Remove the 1/2 paper feed drive frame lower. Remove the har-
ness clamp.
5) Disconnect the connector, and remove the vertical paper transport
motor.
a-2. Paper feed tray 3/4 paper transport clutch 2
1) Remove the 1/2 paper feed drive unit. (See “a. 1/2 paper feed drive
unit” in this section)
2) Remove the 1/2 paper feed drive frame lower. (See “a-1. Vertical
paper transport motor” in this section)
3) Disconnect the connector and remove the harness lamp, and
remove the paper feed tray 3/4 and the paper transport clutch 2
unit.
unit.
4) Remove the E-ring, and remove the paper feed tray 3/4 and the
paper transport clutch 2.
a-3. Paper feed clutch (Paper feed tray 1)
1) Remove the 1/2 paper feed drive unit. (See “a. 1/2 paper feed drive
unit” in this section)
2) Remove the 1/2 paper feed drive frame lower. (See “a-1. Vertical
paper transport motor” in this section)
3) Disconnect the connector and remove the harness lamp, and
remove the paper feed clutch unit.
4) Remove the E-ring, and remove the paper feed clutch.
Click on the first or last page to see other AR-M550 (serv.man13) service manuals if exist.