DOWNLOAD Sharp AR-M351U / AR-M451U (serv.man17) Service Manual ↓ Size: 887.33 KB | Pages: 88 in PDF or view online for FREE

AR-M351U/M451U, AR-M355U/M455U  SIMULATION  9 - 6

66

2

3

4

5

Used to check the output operation of data 
signals in each data output mode of FAX. (Used 
to check the operation of MODEM.) An output is 
sent at the send level set by the soft switch. (Only 
when FAX is installed)

6

Used to print the confidential pass code. (Used 
when the confidential pass code is forgotten.) 
(Only when FAX is installed)

7

Used to print the image memory data (memory 
send/receive). (Only when FAX is installed)

8

Used to check the output operation of various 
sound signals of FAX. (Used to check the 
operation of the sound output IC.) Send level: 
Max. (Only when FAX is installed)

9

Used to check the output operation of various 
sound signals of FAX. (Used to check the 
operation of the sound output IC.) An output is 
sent at the send level set by the soft switch. (Only 
when FAX is installed)

10

Used to clear all data of the image memory 
(memory send/receive). The confidential data are 
also cleared at the same time. (Only when FAX is 
installed)

11

Used to check the output operation of FAX G3 
mode 300bps. (Used to check the operation of 
MODEM.) Send level: Max. (Only when FAX is 
installed)

12

Used to check the output operation of FAX G3 
mode 300bps. (Used to check the operation of 
MODEM.) An output is send at the send level set 
by the soft switch. (Only when FAX is installed)

13

Used to enter (set) the number of FAX dial signal 
output test. (The dial number set by this 
simulation is outputted when the dial signal output 
test is made by SIM 66-14 - 16. ) (Only when FAX 
is installed)

14

Used to set the make time in the FAX pulse dial 
mode (10pps) and to test the dial signal output. 
(The dial number signal set by SIM 66-13 is 
outputted.) Used to check troubles in dialing and 
to check the operation. (Only when FAX is 
installed)

15

Used to set the make time in the FAX pulse dial 
mode (20pps) and to test the dial signal output. 
(The dial number signal set by SIM 66-13 is 
outputted.) Used to check troubles in dialing and 
to check the operation. (Only when FAX is 
installed)

16

Used to check the dial signal (DTMF) output in 
the FAX tone dial mode. (The dial number signal 
set by SIM 66-13 is outputted.) The send level 
can be set to an optional level. Used to check 
troubles in dialing and to check the operation. 
(Only when FAX is installed)

Code

Function (Purpose)

Main

Sub

66

17

Used to check the dial signal (DTMF) output in 
the FAX tone dial mode.  Send level: Max. Used 
to check the operation. (Only when FAX is 
installed)

18

Used to check the dial signal (DTMF) output in 
the FAX tone dial mode.  An output is sent at the 
send level set by the soft switch. Used to check 
the operation. (Only when FAX is installed)

19

Used to back-up the HDD data into the Flash 
memory (optional FAX expansion memory: AR-
MM9). (Only when FAX is installed)

20

Used to read the back-up data by SIM 66-19 to 
the SRAM/HDD. (Only when FAX is installed)

21

Used to print information related to FAX (various 
registrations, communication management, file 
management, system error protocol). (Only when 
FAX is installed)

22

Used to adjust the handset volume. (Only when 
the FAX is installed.)

23

Used to download the FAX program. (Only when 
FAX is installed)
Not used in the market. (For development)

24

Used to clear the FAST memory data. (Only when 
FAX is installed)

25

Used to register the FAX number for Modem dial-
in. (Only when FAX is installed)
Not used in the market. (For development)

26

Used to register external telephone numbers for 
Modem dial-in. (Only when FAX is installed)
Not used in the market. (For development)

27

Used to register the transfer number for voice 
warp. (Only when FAX is installed)
Not used in the market. (For development)

29

Used to clear data related to an address book 
(one-touch registration, program registration/
expansion, relay memory box registration, each 
table content).

30

31

32

33

34

35

36

39

42

43

67

2

Used to check the operation of the parallel I/F of 
the printer. (This simulation is for production only, 
and requires a special tool for execution. Not 
used in the market.)

11

Used to set YES/NO of the parallel I/F select 
signal of the printer.

16

Used to check the operation of the network card.

Code

Function (Purpose)

Main

Sub

AR-M351U/M451U, AR-M355U/M455U  SIMULATION  9 - 7

1) Select the operation mode with 10-key.

2) Press START key.

The scanner performs scanning at the speed corresponding to
the operation mode.

The sensor and detector operation conditions are displayed.

The active sensors and detectors are highlighted.

• The scanner (read) unit is in the home position.: "MHPS" section

is highlighted.

• The scanner (read) unit is not in the home position.: "MHPS" is

normally displayed.

1) Select the operation mode with 10-key.

2) Press START key.

The SPF repeat paper feed, transport, and paper exit at the
speed corresponding to the operation mode.

The operation can be stopped by [CUSTOM SETTINGS] key.

The operating conditions of the sensors and detectors are dis-
played.

The active sensors and detectors are highlighted.

1-1

Operation test/Check

Used to check the operations of the scanner 
(read) unit and its control circuit.

Optical (Image scanning)

Operation

1

TOP SPEED

Top speed (220mm/s)

2

HIGH SPEED

High speed (168.7mm/s)

3

MIDDLE SPEED

Middle speed (110mm/s)

4

LOW SPEED

Low speed (55mm/s)

Press [START] key, and the 
operation is started.

Press [CUSTOM SETTINGS] key, and 
scanning is stopped.

1-2

Operation test/Check

Used to check the operation of sensor and 
detector in the scanning (read) section and the 
related circuit.

Optical (Image scanning)

Operation

MHPS

Optical system home position

SIMULATION 1-1
SCANNER CHECK. SELECT 1-4, AND PRESS START.
1. TOP SPEED
2. HIGH SPEED
3. MIDDLE SPEED
4. LOW SPEED

1

SIMULATION 1-1
SCANNER CHECK. EXECUTING···.
1. TOP SPEED
2. HIGH SPEED
3. MIDDLE SPEED
4. LOW SPEED

1

SIMULATION 1-2

SCANNER SENSOR CHECK..

MHPS

2-1

Operation test/Check

Used to check the operations of the automatic 
document feeder unit and the control circuit.

DSPF

Operation

1

HIGH SPEED

High speed

2

LOW SPEED

Low speed

Press [START] key, and the 
operation is started.

Press [CUSTOM SETTINGS] key, and 
the operation is stopped.

2-2

Operation test/Check

Used to check the operations of the sensors and 
detectors in the automatic document feeder unit 
and the related circuits.

DSPF

Operation

SPFSET

SPF sensor

SOCD

Open/close sensor

SCOV

Paper feed cover sensor

SPED

Document set sensor

SPPD

Resist front detection sensor

SPOD

Document paper exit sensor

SWDn

Document width sensor (n 

→

 1 (inside) - 6 

(outside))

SPLSn

Document length sensor (n 

→

 1 (inside) - 2 

(outside))

CISSET

CIS installation detection

STSET

Stamp unit installation sensor

SWD_LEN

SPF guide plate position (unit: 0.1mm)

SWD_AD

SPF document width detection volume output AD 
value

SIMULATION 2-1

SPF AGING TEST. SELECT 1-2, AND PRESS START.

1. HIGH SPEED

2. LOW SPEED

2

SIMULATION 2-1

SPF AGING TEST. EXECUTING···.

1. HIGH SPEED

2. LOW SPEED

2

AR-M351U/M451U, AR-M355U/M455U  SIMULATION  9 - 8

1) Select the number corresponding to the target of operation

check with 10-key.

2) Press START key.

The load selected in procedure 1 is operated.

Press [CUSTOM SETTINGS] key to stop the operation of the load.

The operating conditions of the sensors and detectors are dis-
played.

The active sensors and detectors are highlighted.

• The following units are added when the punch unit is installed to

the console finisher:

2-3

Operation test/Check

Used to check the operations of the loads in the 
automatic document feeder unit and the control 
circuits.

DSPF

Operation

1

MOTOR(H)

Motor high speed

2

MOTOR(L)

Motor low speed

3

SDSS

SPF gate solenoid

4

SPFS

SPF pick-up solenoid

5

SPFC

SPF paper feed clutch

6

SRRC

SPF resist roller clutch

7

STMPS

Stamp solenoid

Press [START] key, and the 
operation is started.

Press [CUSTOM SETTINGS] key, and the 
operation is stopped.

3-2

Operation test/Check

Used to check the operation of sensor and 
detector in the finisher and the related circuit.

Finisher

Operation

SIMULATION 2-2

SPF SENSOR CHECK.

SPFSET

        

SOCD

        

SCOV

        SPED

SPPD          SPOD        

SWD6

        SWD5

SWD4          SWD3        SWD2        SWD1

SPLS2         SPLS1       

CISSET

      STSET

SWD_LEN:

2100

             SWD_AD:

600

SIMULATION 2-3

SPF LOAD TEST. SELECT 1-7, AND PRESS START.

1.MOTOR(H)  2.MOTOR(L) 

3.SDSS      4.SPFS    5.SPFC    6.SRRC

7.STMPS

2

SIMULATION 2-3

SPF LOAD TEST. EXECUTING···.

1.MOTOR(H) 2.MOTOR(L) 

3.SDSS     4.SPFS    5.SPFC    6.SRRC

7.STMPS

2

Built-in finisher

STHP

Stapler HP detection

POD

Tray 2 paper exit detection

SCID

Staple compiler paper entry detection

PID

Paper entry detection 

T2PD

Tray 2 paper empty detection

T2DN

Tray 2 lower limit detection 

T2UP

Tray 2 upper limit detection

JRHP

Jogger R HP

JFHP

Jogger (F) HP

SCID2

Staple compiler paper entry detection 2

STTHP2

Staple rotation HP detection 2

STTHP1

Staple rotation HP detection 1

STUHP

Staple shift HP detection

PSHP

Pusher HP detection

PPD

Paper hold return detection 

DSW2

Staple replacement door open detection

DSW1

Compiler jam cancel door open detection

24VM

24V power supply

T1PF

Tray 1 full detection

STSP

Stapling ready detection 

STLS

Cartridge inside spare staple empty detection

STNC

Cartridge empty detection

DOPD

Interface unit door open detection

MMLK

Main drive motor lock detection 

SCPD

Staple compiler paper empty detection

Console finisher

FSSS

Stapler safety switch

FJS

Joint switch

FFDSW

Front door switch

FTCS

Upper cover sensor

FFDS

Front door sensor

FSPS

Self prime sensor

FSUC

Stapler connection detection

FSS

Staple sensor

FSTHPS

Stapler HP sensor

FSHPS

Slide HP sensor

FLE

Lift lock sensor

FLLLS

Lift lower limit sensor

FULS

Lift upper limit sensor

FFE

Bookbinding clock sensor

FFES

Bookbinding paper sensor

FFRHPS

Bookbinding roller HP sensor

FFHPS

Bookbinding HP sensor

FFPS

Bookbinding position sensor

FSLS

Paper surface sensor

FBES

Tray paper sensor

FOBHPS

Paper exit belt HP sensor

FAS

Alignment tray sensor

FRJHPS

Alignment HP sensor R

FFJHPS

Alignment HP sensor F

FARHPS

Bundle roller HP sensor

FPHPS

Paddle HP sensor

FES

Entry port sensor

FPE

Punch motor encoder

FPSHPS

Punch side register HP

FPUC

Punch connection detection

FPDS

Punch dust sensor

FPDSS4

Punch side register sensor 4

FPDSS3

Punch side register sensor 3

FPDSS2

Punch side register sensor 2

FPDSS1

Punch side register sensor 1

FPTS

Punch timing sensor

AR-M351U/M451U, AR-M355U/M455U  SIMULATION  9 - 9

(Built-in finisher)

(Console finisher)

( ) : Added when the punch unit is installed.

1) Select the number corresponding to the target of operation

check with 10-key.

2) Press START key.

The load selected in procedure 1 is operated.

Press [CUSTOM SETTINGS] key to stop the operation of the
load.

Enter the adjustment value with 10 digit key pad and press START
key. The jogger moves to LT position (Inch series) or A4 position
(AB series) according to the entered value, and stops there.

1) Select the number corresponding to the target of operation

check with 10-key.

2) Press [START] key.

3) Enter the adjustment value with 10-key.

4) Press [START] key. (The entered value is stored.)

3-3

Operation test/Check

Used to check the operation of the load in the 
finisher and the control circuit.

Finisher

Operation

Built-in finisher

1

T2S

Tray 2 solenoid

2

T2OM

Paper exit motor

3

SPS

Stopper solenoid

4

SCRS

Roller pressure release solenoid

5

PPS

Rear edge h folding solenoid

6

SCGS

Compiler gate solenoid

7

STTM

Staple rotation motor

8

STUM

Stapler shift motor

9

MM

Main drive motor

10

EVM

Elevator motor

11

STM

Staple motor

12

JRM

Jogger motor rear

13

JFM

Jogger motor front

14

PSM

Pusher motor

Console finisher

1

FFC

Folding clutch

2

FPSM

Puncher side register motor

3

FPNM

Punch motor

4

FLM

Shift  motor

5

FFSM

Stapler motor

6

FSM

Slide motor

7

FRJM

Alignment motor R

8

FFJM

Alignment motor F

9

FAM

Bundle exit motor

10

FPM

Paddle motor

11

FFM

Transport motor

SIMULATION 3-3

FINISHER SENSOR CHECK.

PID           SCID         SCID2         PPD

SCPD          POD          T1PF          T2UP

T2DN          T2PD         STSP          STLS

STNC          STHP         JFHP          JRHP

PSHP          STUHP        STTHP1

STTHP2        DOPD         DSW1          DSW2

24VM          MMLK

SIMULATION 3-2

FINISHER SENSOR CHECK.

FSSS  FJS     FFDSW  FTCS    FFDS 

FSPS  FSUC    FSS    FSTHPS  FSHPS   FLE     FLLLS

FULS  FFE     FFES   FFRHPS  FFHPS   FFPS    FSLS

FBES  FOBHPS  FAS    FRJHPS  FFJHPS  FARHPS  FPHPS

FES

(FPE)(FPSHPS)(FPUC)(FPDS)(FPDSS4)(FPDSS3)(FPDSS2)

(FPDSS1)(FPTS)

Press [START] key, and the operation 
is started.

Press [CUSTOM SETTINGS] key, and 
the operation is stopped.

3-6

Adjustment

Used to adjust the stacking capacity of the 
finisher. (Used to adjust the alignment plate 
(jogger) stop position in the finisher paper width 
direction. The adjustment is made by changing the 
alignment plate home position in the paper width 
direction by software.)

Finisher

Operation

Press [START] key, and the 
operation is started.

Press [CUSTOM SETTINGS] key, and the 
operation is stopped.
Stops when the operation is terminated.

3-10

Adjustment

Console finisher (AR-FN7) adjustment

Finisher

Operation

Item

Set 

range

Initial 
value

1STEP

1

Saddle binding position 
adjustment

0 - 400

200

0.0707mm

2

Saddle folding position 
adjustment

0 - 400

200

0.0525mm

3

Front alignment position 
adjustment

0 - 20

10

0.367mm

4

Rear alignment position 
adjustment

0 - 20

10

0.367mm

SIMULATION 3-3

FINISHER LOAD TEST. SELECT 1-

AND PRESS START.

2

SIMULATION 3-3

FINISHER LOAD TEST. EXECUTING

.

2

SIMULATION 3-6

FINISHER JOGGER ADJUSTMENT. INPUT VALUE 40-60, AND PRESS START.

50

SIMULATION 3-6

FINISHER JOGGER ADJUSTMENT. MOVING....

50