Sharp AR-M351U / AR-M451U (serv.man17) Service Manual ▷ View online
AR-M351U/M451U, AR-M355U/M455U SIMULATION 9 - 4
24
6
Used to reset the copy counter.
7
Used to clear the OPC drum counter. (Perform
this simulation when the OPC drum is replaced.)
this simulation when the OPC drum is replaced.)
9
Used clear the printer mode print counter and the
self print mode print counter.
self print mode print counter.
10
Used to clear the FAX counter. (Only when FAX
is installed)
is installed)
11
Used to reset the OPC drum rotation time, and
the DV unit rotation time counter. The developer
counter in the DV unit installed is reset.
the DV unit rotation time counter. The developer
counter in the DV unit installed is reset.
15
Used to clear the counters related to the scan
mode and the internet FAX mode.
mode and the internet FAX mode.
25
1
Used to check the operations of the developing
section (toner concentration, humidity and toner
concentration sensor, humidity sensor,
temperature sensor output can be monitored.)
section (toner concentration, humidity and toner
concentration sensor, humidity sensor,
temperature sensor output can be monitored.)
2
Used to make the initial setting of toner
concentration when replacing developer.
concentration when replacing developer.
26
3
Used to set the specifications of the auditor.
Setting must be made according to the auditor
use conditions.
Setting must be made according to the auditor
use conditions.
5
Used to set the count mode of the total counter
and the maintenance counter.
and the maintenance counter.
6
Used to set the specifications (paper, document
detection, etc.) of the destination.
detection, etc.) of the destination.
10
Used to set the network scanner trial mode.
18
Used to set YES/NO of toner save operation.
(This function is valid only in Japan and UK
versions. (Depends on the destination setting of
SIM26-6.) For the other destinations, the same
setting can be made by the user program P22.)
(This function is valid only in Japan and UK
versions. (Depends on the destination setting of
SIM26-6.) For the other destinations, the same
setting can be made by the user program P22.)
30
Used to set the operation mode conforming to the
CE mark (Europe safety standards). (Conforming
to soft start when driving the fusing heater lamp.)
CE mark (Europe safety standards). (Conforming
to soft start when driving the fusing heater lamp.)
35
Used to set whether the same continuous
troubles are displayed as one trouble or the
series of troubles with SIM 22-4 when the same
troubles occur continuously.
troubles are displayed as one trouble or the
series of troubles with SIM 22-4 when the same
troubles occur continuously.
38
Used to set CONTINUE/STOP of printing when
maintenance timing is over and the count value
reaches 110% of replacement timing (life).
maintenance timing is over and the count value
reaches 110% of replacement timing (life).
41
Used to set the automatic magnification ratio
selection (AMS) in the pamphlet mode.
selection (AMS) in the pamphlet mode.
50
Black-White reverse YES/NO setting
52
Used to set whether non-print paper (insertion
paper, cover paper) (blank image print paper) is
counted up or not.
paper, cover paper) (blank image print paper) is
counted up or not.
68
Used to set ENABLE/DISABLE of the CA key
cancel function of print stop.
cancel function of print stop.
27
1
Used to set the specifications for operations in
case of communication trouble between the host
computer and MODEM (machine side). (When
communication trouble occurs between the host
computer MODEM and the machine, the self diag
display (U7-00) is printed and setting for inhibition
of print or not is made.)
case of communication trouble between the host
computer and MODEM (machine side). (When
communication trouble occurs between the host
computer MODEM and the machine, the self diag
display (U7-00) is printed and setting for inhibition
of print or not is made.)
5
Used to enter the machine tag No. (This function
allows to check the tag No. of the machine with
the host computer.)
allows to check the tag No. of the machine with
the host computer.)
30
1
Used to check the operation of sensors and
detectors in other than the paper feed section and
the operations of the related circuits.
detectors in other than the paper feed section and
the operations of the related circuits.
2
Used to check the operation of sensors and
detectors in the paper feed section and the
related circuits.
detectors in the paper feed section and the
related circuits.
Code
Function (Purpose)
Main
Sub
40
1
Used to check the operation of the manual feed
tray paper size detector and the related circuit.
(The operation of the manual feed tray paper size
detector can be monitored with the LCD display.)
tray paper size detector and the related circuit.
(The operation of the manual feed tray paper size
detector can be monitored with the LCD display.)
2
Used to adjust the manual paper feed tray paper
width detector detection level.
width detector detection level.
7
Used to enter the manual paper feed tray paper
width adjustment value.
width adjustment value.
11
Used to check the multi-purpose tray width
detection adjustment value.
detection adjustment value.
12
Used to check the multi-purpose tray width
detection adjustment value.
detection adjustment value.
41
1
Used to check the operation of the document size
sensor and the related circuit. (The operation of
the document size sensor can be monitored with
the LCD display.)
sensor and the related circuit. (The operation of
the document size sensor can be monitored with
the LCD display.)
2
Used to adjust the document size sensor sensing
level.
level.
3
Used to check the operation of the document size
sensor and the related circuit. (The document
size sensor output level can be monitored with
the LCD display.)
sensor and the related circuit. (The document
size sensor output level can be monitored with
the LCD display.)
43
1
Used to set the fusing temperature in each
operation mode.
operation mode.
44
1
Used to set enable/disable of correction
operations in the image forming (process)
section.
operations in the image forming (process)
section.
9
Used to check the data related to the image
forming section correction (process correction)
result (corrected main charger grid voltage, the
developing bias voltage, and the laser power
voltage in each print mode). (This simulation
allows to check that correction is performed
normally or not.)
forming section correction (process correction)
result (corrected main charger grid voltage, the
developing bias voltage, and the laser power
voltage in each print mode). (This simulation
allows to check that correction is performed
normally or not.)
14
Used to check the output level of the temperature
sensor and the humidity sensor.
sensor and the humidity sensor.
16
Used to check the toner concentration control
data.
data.
46
2
Used to adjust the copy density in all the copy
modes (Auto, Text, Text/Photo, and Photo mode).
modes (Auto, Text, Text/Photo, and Photo mode).
9
Used to adjust the print density for each density
level (display value) in the copy mode (binary -
Text mode). An optional print density can be set
for each density level (display value).
level (display value) in the copy mode (binary -
Text mode). An optional print density can be set
for each density level (display value).
10
Used to adjust the print density for each density
level (display value) in the copy mode (binary -
Text/Photo mode). An optional print density can
be set for each density level (display value).
level (display value) in the copy mode (binary -
Text/Photo mode). An optional print density can
be set for each density level (display value).
11
Used to adjust the print density for each density
level (display value) in the copy mode (binary -
Photo mode). An optional print density can be set
for each density level (display value).
level (display value) in the copy mode (binary -
Photo mode). An optional print density can be set
for each density level (display value).
12
Used to adjust the print density in the FAX mode
(all modes).
(all modes).
13
Used to adjust the print density in the FAX mode
(each normal mode). (Only when FAX is
installed.)
(each normal mode). (Only when FAX is
installed.)
14
Used to adjust the print density in the FAX mode
(each fine mode). (Only when FAX is installed.)
(each fine mode). (Only when FAX is installed.)
15
Used to adjust the print density in the FAX mode
(each super fine mode). (Only when FAX is
installed.)
(each super fine mode). (Only when FAX is
installed.)
16
Used to adjust the print density in the FAX mode
(each ultra fine mode). (Only when FAX is
installed.)
(each ultra fine mode). (Only when FAX is
installed.)
17
Used to set the gain in shading correction.
Code
Function (Purpose)
Main
Sub
AR-M351U/M451U, AR-M355U/M455U SIMULATION 9 - 5
46
18
Used to adjust the gamma (density gradient) in
the copy mode.
the copy mode.
19
Used to set the auto mode operation
specifications in each mode (copy, scan, FAX).
specifications in each mode (copy, scan, FAX).
20
Used to adjust the copy density correction in the
SPF copy mode for the document table copy
mode. The adjustment is made so that the copy
density becomes the same as that of the
document table copy mode.
SPF copy mode for the document table copy
mode. The adjustment is made so that the copy
density becomes the same as that of the
document table copy mode.
21
Used to adjust the scanner exposure level in all
the scanner modes.
the scanner modes.
22
Used to adjust the scanner exposure level in the
normal text mode.
normal text mode.
23
Used to adjust the scanner exposure level in the
fine text mode.
fine text mode.
24
Used to adjust the scanner exposure level (in the
super fine text mode).
super fine text mode).
25
Used to adjust the scanner exposure level in the
ultra fine text mode.
ultra fine text mode.
27
Used to adjust the gamma (density gradient) of
the network scanner mode.
the network scanner mode.
31
Used to adjust sharpness of the copy mode.
39
Used to adjust sharpness of the FAX mode.
45
Used to adjust the image density in the FAX
mode (600dpi).
mode (600dpi).
46
Used to adjust sharpness of the scanner mode.
48
1
Used to adjust the copy magnification ratio (in the
main scanning and the sub scanning directions).
main scanning and the sub scanning directions).
5
Used to adjust the copy magnification ratio in the
sub scanning direction.
sub scanning direction.
6
HSYNC cycle adjustment
50
1
Used to adjust the copy image position and the
void area (image loss) adjustment on print paper
in the copy mode. (The similar adjustment can be
performed with SIM 50-5 and 50-2 (Simplified
method).) (Document table mode)
void area (image loss) adjustment on print paper
in the copy mode. (The similar adjustment can be
performed with SIM 50-5 and 50-2 (Simplified
method).) (Document table mode)
2
Used to adjust the document scan position, the
image print position, and the void area (image
loss). (Simple adjustment) (This adjustment is the
simple method of SIM 50-1.) (Document table
mode)
image print position, and the void area (image
loss). (Simple adjustment) (This adjustment is the
simple method of SIM 50-1.) (Document table
mode)
5
Used to adjust the print image position and the
void area (image loss) on print paper.
(Adjustment as the print engine) (This adjustment
is reflected on all the FAX/printer/copy modes.)
void area (image loss) on print paper.
(Adjustment as the print engine) (This adjustment
is reflected on all the FAX/printer/copy modes.)
6
Used to adjust the copy image position and void
area (image loss) on print paper in the copy
mode. (The similar adjustment can be performed
with SIM 50-7 (simple method).) (SPF mode)
area (image loss) on print paper in the copy
mode. (The similar adjustment can be performed
with SIM 50-7 (simple method).) (SPF mode)
7
Used to adjust the copy image position and void
area (image loss) on print paper in the copy
mode. (The similar adjustment can be performed
with SIM 50-6.) (SPF mode)
area (image loss) on print paper in the copy
mode. (The similar adjustment can be performed
with SIM 50-6.) (SPF mode)
10
Used to adjust the print image off-center position.
(Adjusted separately for each paper feed
section.)
(Adjusted separately for each paper feed
section.)
12
Used to adjust the scan image off-center position.
(Adjusted separately for each scan mode.)
(Adjusted separately for each scan mode.)
27
Used to adjust the image loss of the scan image
in the FAX/scan mode.
in the FAX/scan mode.
51
2
Used to adjust the contact pressure of paper on
the resist roller of each section (each paper feed,
duplex feed and SPF paper feed of the copier).
(This adjustment is required when the print image
position variations are considerably great or when
paper jams occur frequently.)
the resist roller of each section (each paper feed,
duplex feed and SPF paper feed of the copier).
(This adjustment is required when the print image
position variations are considerably great or when
paper jams occur frequently.)
Code
Function (Purpose)
Main
Sub
53
6
Used to adjust the DSPF width detection level.
7
Used to enter the SPF width detection adjustment
value.
value.
8
Used to adjust the document scan start position.
(Used to adjust the scanner scan position in the
SPF mode front scan.)
(Used to adjust the scanner scan position in the
SPF mode front scan.)
55
1
Used to set the specifications of the engine
control operations. (PCU PWB)
control operations. (PCU PWB)
2
Used to set the specifications of the scanner
control operations. (Scanner control PWB)
control operations. (Scanner control PWB)
3
Used to set the specifications of the controller
operations. (MFP control PWB)
operations. (MFP control PWB)
56
1
Used to transfer the MFP controller data. (Used to
repair the PWB.)
repair the PWB.)
60
1
Used to check the MFP control (DRAM)
operations (read/write).
operations (read/write).
61
1
Used to check the operation of the scanner (write)
unit (LSU).
unit (LSU).
2
Used to adjust the laser power (absolute value) in
the copy mode.
the copy mode.
3
Used to adjust the laser power (absolute value) in
the FAX mode.
the FAX mode.
4
Used to adjust the laser power (absolute value) in
the printer mode.
the printer mode.
62
1
Used to format the hard disk. (Only in the model
with a disk installed)
with a disk installed)
2
Used to check the operation of the hard disk
(read/write). (Only in the model with a disk
installed) (Partial check)
(read/write). (Only in the model with a disk
installed) (Partial check)
3
Used to check the operation of the hard disk
(read/write). (Only in the model with a disk
installed) (All areas check)
(read/write). (Only in the model with a disk
installed) (All areas check)
6
Used to check the operations of the hard disk.
(The self diag operation of the SMART function is
executed.) (Only in the model with a disk
installed)
(The self diag operation of the SMART function is
executed.) (Only in the model with a disk
installed)
7
Used to check the operations of the hard disk.
(The result of the self diag operation of the
SMART function is printed out.) (Only in the
model with a disk installed)
(The result of the self diag operation of the
SMART function is printed out.) (Only in the
model with a disk installed)
8
Used to format the hard disk (the system area
excluded). (Only in the model with a disk
installed)
excluded). (Only in the model with a disk
installed)
10
Used to delete a job complete list (also to delete
job log data) (Only in the model with a disk
installed)
job log data) (Only in the model with a disk
installed)
11
Used to delete document filing data. (The
management area (standard folder, user folder) is
cleared.) (Only in the model with a disk installed)
management area (standard folder, user folder) is
cleared.) (Only in the model with a disk installed)
63
1
Used to check the result of shading correction.
(The shading correction data are displayed.)
(The shading correction data are displayed.)
2
Used to execute shading.
7
Used to adjust the white plate scan start position
for shading. (Document table mode)
for shading. (Document table mode)
64
1
Used to check the operation of the printer section
(self-print operation), (The print pattern, the paper
feed mode, the print mode, the print quantity, and
the density can be optionally set.)
(self-print operation), (The print pattern, the paper
feed mode, the print mode, the print quantity, and
the density can be optionally set.)
65
1
Used to adjust the touch panel (LCD display
section) detection position.
section) detection position.
2
Used to check the result of the touch panel (LCD
display) detection position adjustment. (The
coordinates are displayed.)
display) detection position adjustment. (The
coordinates are displayed.)
66
1
Used to change and check the FAX soft switch
functions. (Used to change and check the
functions provided for the FAX soft switches.)
(Only when FAX is installed)
functions. (Used to change and check the
functions provided for the FAX soft switches.)
(Only when FAX is installed)
Code
Function (Purpose)
Main
Sub
AR-M351U/M451U, AR-M355U/M455U SIMULATION 9 - 6
66
2
Used to clear the FAX soft switch function data
and to set to the default. (Excluding the
adjustment values.) (Only when FAX is installed)
and to set to the default. (Excluding the
adjustment values.) (Only when FAX is installed)
3
Used to check the operation of the FAX PWB
memory (read/write). (This adjustment is required
when the PWB is replaced with a new one.) (Only
when FAX is installed)
memory (read/write). (This adjustment is required
when the PWB is replaced with a new one.) (Only
when FAX is installed)
4
Used to check the output operation of data
signals in each data output mode of FAX. (Used
to check the operation of MODEM. ) Send level:
Max. (Only when FAX is installed)
signals in each data output mode of FAX. (Used
to check the operation of MODEM. ) Send level:
Max. (Only when FAX is installed)
5
Used to check the output operation of data
signals in each data output mode of FAX. (Used
to check the operation of MODEM.) An output is
sent at the send level set by the soft switch. (Only
when FAX is installed)
signals in each data output mode of FAX. (Used
to check the operation of MODEM.) An output is
sent at the send level set by the soft switch. (Only
when FAX is installed)
6
Used to print the confidential pass code. (Used
when the confidential pass code is forgotten.)
(Only when FAX is installed)
when the confidential pass code is forgotten.)
(Only when FAX is installed)
7
Used to print the image memory data (memory
send/receive). (Only when FAX is installed)
send/receive). (Only when FAX is installed)
8
Used to check the output operation of various
sound signals of FAX. (Used to check the
operation of the sound output IC.) Send level:
Max. (Only when FAX is installed)
sound signals of FAX. (Used to check the
operation of the sound output IC.) Send level:
Max. (Only when FAX is installed)
9
Used to check the output operation of various
sound signals of FAX. (Used to check the
operation of the sound output IC.) An output is
sent at the send level set by the soft switch. (Only
when FAX is installed)
sound signals of FAX. (Used to check the
operation of the sound output IC.) An output is
sent at the send level set by the soft switch. (Only
when FAX is installed)
10
Used to clear all data of the image memory
(memory send/receive). The confidential data are
also cleared at the same time. (Only when FAX is
installed)
(memory send/receive). The confidential data are
also cleared at the same time. (Only when FAX is
installed)
11
Used to check the output operation of FAX G3
mode 300bps. (Used to check the operation of
MODEM.) Send level: Max. (Only when FAX is
installed)
mode 300bps. (Used to check the operation of
MODEM.) Send level: Max. (Only when FAX is
installed)
12
Used to check the output operation of FAX G3
mode 300bps. (Used to check the operation of
MODEM.) An output is send at the send level set
by the soft switch. (Only when FAX is installed)
mode 300bps. (Used to check the operation of
MODEM.) An output is send at the send level set
by the soft switch. (Only when FAX is installed)
13
Used to enter (set) the number of FAX dial signal
output test. (The dial number set by this
simulation is outputted when the dial signal output
test is made by SIM 66-14 - 16. ) (Only when FAX
is installed)
output test. (The dial number set by this
simulation is outputted when the dial signal output
test is made by SIM 66-14 - 16. ) (Only when FAX
is installed)
14
Used to set the make time in the FAX pulse dial
mode (10pps) and to test the dial signal output.
(The dial number signal set by SIM 66-13 is
outputted.) Used to check troubles in dialing and
to check the operation. (Only when FAX is
installed)
mode (10pps) and to test the dial signal output.
(The dial number signal set by SIM 66-13 is
outputted.) Used to check troubles in dialing and
to check the operation. (Only when FAX is
installed)
15
Used to set the make time in the FAX pulse dial
mode (20pps) and to test the dial signal output.
(The dial number signal set by SIM 66-13 is
outputted.) Used to check troubles in dialing and
to check the operation. (Only when FAX is
installed)
mode (20pps) and to test the dial signal output.
(The dial number signal set by SIM 66-13 is
outputted.) Used to check troubles in dialing and
to check the operation. (Only when FAX is
installed)
16
Used to check the dial signal (DTMF) output in
the FAX tone dial mode. (The dial number signal
set by SIM 66-13 is outputted.) The send level
can be set to an optional level. Used to check
troubles in dialing and to check the operation.
(Only when FAX is installed)
the FAX tone dial mode. (The dial number signal
set by SIM 66-13 is outputted.) The send level
can be set to an optional level. Used to check
troubles in dialing and to check the operation.
(Only when FAX is installed)
Code
Function (Purpose)
Main
Sub
66
17
Used to check the dial signal (DTMF) output in
the FAX tone dial mode. Send level: Max. Used
to check the operation. (Only when FAX is
installed)
the FAX tone dial mode. Send level: Max. Used
to check the operation. (Only when FAX is
installed)
18
Used to check the dial signal (DTMF) output in
the FAX tone dial mode. An output is sent at the
send level set by the soft switch. Used to check
the operation. (Only when FAX is installed)
the FAX tone dial mode. An output is sent at the
send level set by the soft switch. Used to check
the operation. (Only when FAX is installed)
19
Used to back-up the HDD data into the Flash
memory (optional FAX expansion memory: AR-
MM9). (Only when FAX is installed)
memory (optional FAX expansion memory: AR-
MM9). (Only when FAX is installed)
20
Used to read the back-up data by SIM 66-19 to
the SRAM/HDD. (Only when FAX is installed)
the SRAM/HDD. (Only when FAX is installed)
21
Used to print information related to FAX (various
registrations, communication management, file
management, system error protocol). (Only when
FAX is installed)
registrations, communication management, file
management, system error protocol). (Only when
FAX is installed)
22
Used to adjust the handset volume. (Only when
the FAX is installed.)
the FAX is installed.)
23
Used to download the FAX program. (Only when
FAX is installed)
Not used in the market. (For development)
FAX is installed)
Not used in the market. (For development)
24
Used to clear the FAST memory data. (Only when
FAX is installed)
FAX is installed)
25
Used to register the FAX number for Modem dial-
in. (Only when FAX is installed)
Not used in the market. (For development)
in. (Only when FAX is installed)
Not used in the market. (For development)
26
Used to register external telephone numbers for
Modem dial-in. (Only when FAX is installed)
Not used in the market. (For development)
Modem dial-in. (Only when FAX is installed)
Not used in the market. (For development)
27
Used to register the transfer number for voice
warp. (Only when FAX is installed)
Not used in the market. (For development)
warp. (Only when FAX is installed)
Not used in the market. (For development)
29
Used to clear data related to an address book
(one-touch registration, program registration/
expansion, relay memory box registration, each
table content).
(one-touch registration, program registration/
expansion, relay memory box registration, each
table content).
30
Used to check the change in the TEL/LIU status.
(Only when FAX is installed)
(Only when FAX is installed)
31
Used to check the relay operation. (Only when
FAX is installed)
FAX is installed)
32
Used to check the receive data (fixed data) from
the line. (Only when FAX is installed)
the line. (Only when FAX is installed)
33
Used to check the signal (BUSY TONE/CNG/
CED/FNET/DTMF) detection. (Only when FAX is
installed)
CED/FNET/DTMF) detection. (Only when FAX is
installed)
34
Used to measure the communication time of test
image data. (Only when FAX is installed)
image data. (Only when FAX is installed)
35
Modem program rewriting. (Only when FAX is
installed) Not used in the market. (For
development)
installed) Not used in the market. (For
development)
36
Used to check interface between MFPC controller
and MDMC. (Check of the data line or the
command line) (Only when FAX is installed)
and MDMC. (Check of the data line or the
command line) (Only when FAX is installed)
39
Used to set the destination specifications. (Only
when FAX is installed)
when FAX is installed)
42
PIC program rewriting (Only when FAX is
installed)
installed)
43
PIC adjustment value writing (Only when FAX is
installed)
installed)
67
2
Used to check the operation of the parallel I/F of
the printer. (This simulation is for production only,
and requires a special tool for execution. Not
used in the market.)
the printer. (This simulation is for production only,
and requires a special tool for execution. Not
used in the market.)
11
Used to set YES/NO of the parallel I/F select
signal of the printer.
signal of the printer.
16
Used to check the operation of the network card.
Code
Function (Purpose)
Main
Sub
AR-M351U/M451U, AR-M355U/M455U SIMULATION 9 - 7
C. Details
Operation/Procedure
1) Select the operation mode with 10-key.
2) Press START key.
The scanner performs scanning at the speed corresponding to
the operation mode.
the operation mode.
Operation/Procedure
The sensor and detector operation conditions are displayed.
The active sensors and detectors are highlighted.
• The scanner (read) unit is in the home position.: "MHPS" section
is highlighted.
• The scanner (read) unit is not in the home position.: "MHPS" is
normally displayed.
Operation/Procedure
1) Select the operation mode with 10-key.
2) Press START key.
The SPF repeat paper feed, transport, and paper exit at the
speed corresponding to the operation mode.
speed corresponding to the operation mode.
The operation can be stopped by [CUSTOM SETTINGS] key.
Operation/Procedure
The operating conditions of the sensors and detectors are dis-
played.
played.
The active sensors and detectors are highlighted.
1
1-1
Purpose
Operation test/Check
Function
(Purpose)
(Purpose)
Used to check the operations of the scanner
(read) unit and its control circuit.
(read) unit and its control circuit.
Section
Optical (Image scanning)
Item
Operation
1
TOP SPEED
Top speed (220mm/s)
2
HIGH SPEED
High speed (168.7mm/s)
3
MIDDLE SPEED
Middle speed (110mm/s)
4
LOW SPEED
Low speed (55mm/s)
Press [START] key, and the
operation is started.
operation is started.
Press [CUSTOM SETTINGS] key, and
scanning is stopped.
scanning is stopped.
1-2
Purpose
Operation test/Check
Function
(Purpose)
(Purpose)
Used to check the operation of sensor and
detector in the scanning (read) section and the
related circuit.
detector in the scanning (read) section and the
related circuit.
Section
Optical (Image scanning)
Item
Operation
MHPS
Optical system home position
SIMULATION 1-1
SCANNER CHECK. SELECT 1-4, AND PRESS START.
1. TOP SPEED
2. HIGH SPEED
3. MIDDLE SPEED
4. LOW SPEED
SCANNER CHECK. SELECT 1-4, AND PRESS START.
1. TOP SPEED
2. HIGH SPEED
3. MIDDLE SPEED
4. LOW SPEED
1
SIMULATION 1-1
SCANNER CHECK. EXECUTING···.
1. TOP SPEED
2. HIGH SPEED
3. MIDDLE SPEED
4. LOW SPEED
SCANNER CHECK. EXECUTING···.
1. TOP SPEED
2. HIGH SPEED
3. MIDDLE SPEED
4. LOW SPEED
1
SIMULATION 1-2
SCANNER SENSOR CHECK..
MHPS
2
2-1
Purpose
Operation test/Check
Function
(Purpose)
(Purpose)
Used to check the operations of the automatic
document feeder unit and the control circuit.
document feeder unit and the control circuit.
Section
DSPF
Item
Operation
1
HIGH SPEED
High speed
2
LOW SPEED
Low speed
Press [START] key, and the
operation is started.
operation is started.
Press [CUSTOM SETTINGS] key, and
the operation is stopped.
the operation is stopped.
2-2
Purpose
Operation test/Check
Function
(Purpose)
(Purpose)
Used to check the operations of the sensors and
detectors in the automatic document feeder unit
and the related circuits.
detectors in the automatic document feeder unit
and the related circuits.
Section
DSPF
Item
Operation
SPFSET
SPF sensor
SOCD
Open/close sensor
SCOV
Paper feed cover sensor
SPED
Document set sensor
SPPD
Resist front detection sensor
SPOD
Document paper exit sensor
SWDn
Document width sensor (n
→
1 (inside) - 6
(outside))
SPLSn
Document length sensor (n
→
1 (inside) - 2
(outside))
CISSET
CIS installation detection
STSET
Stamp unit installation sensor
SWD_LEN
SPF guide plate position (unit: 0.1mm)
SWD_AD
SPF document width detection volume output AD
value
value
SIMULATION 2-1
SPF AGING TEST. SELECT 1-2, AND PRESS START.
1. HIGH SPEED
2. LOW SPEED
2
SIMULATION 2-1
SPF AGING TEST. EXECUTING···.
1. HIGH SPEED
2. LOW SPEED
2