Sharp AR-M351U / AR-M451U (serv.man17) Service Manual ▷ View online
AR-M351U/M451U, AR-M355U/M455U SIMULATION 9 - 16
Operation/Procedure
1) Select the number corresponding to the target of the operation
check with 10-key.
2) Press [START] key.
The load selected in procedure 1) is operated.
Press [CUSTOM SETTINGS] key to stop the operation.
Operation/Procedure
The operating conditions of the sensors and detectors are dis-
played.
played.
The active sensors and detectors are highlighted.
Operation/Procedure
1) Select the number corresponding to the target of the operation
check with 10-key.
2) Press [START] key.
The load selected in procedure 1) is operated for 10sec.
Press [CUSTOM SETTINGS] key to stop the operation.
NOTE: Never execute this simulation with toner in the toner hop-
per.
If executed, excessive toner will enter the developing sec-
tion. Be sure to remove the toner motor from the toner hop-
per before execution.
If executed, excessive toner will enter the developing sec-
tion. Be sure to remove the toner motor from the toner hop-
per before execution.
Press [START] key.
Press [CUSTOM SETTINGS] key.
Press [START] key.
Press [CUSTOM SETTINGS] key.
Or after 30sec output.
Or after 30sec output.
9
9-1
Purpose
Operation test/Check
Function
(Purpose)
(Purpose)
Used to check and adjust the operation of the load
(clutch/solenoid) in the duplex section and the
control circuit.
(clutch/solenoid) in the duplex section and the
control circuit.
Section
Duplex
Item
Operation
1
ADMEN1
ADU motor 1 control signal
2
ADMEN2
ADU motor 2 control signal
3
DGS
ADU gate solenoid
Press [START] key.
Press [CUSTOM SETTINGS] key to
stop the operations.
stop the operations.
SIMULATION 8-17
1
TRANSFER ROLLER SETTING. SELECT 1-3, AND PRESS START.
1.SHV FRONT
160
2.SHV BACK
160
3.THV-
780
SIMULATION 8-17
TRANSFER ROLLER SETTING. INPUT VALUE, AND PRESS START.
1.FRONT (0-240)
160
SIMULATION 8-17
TRANSFER ROLLER SETTING. EXECUTING···.
1.FRONT(0-240)
160
SIMULATION 9-1
ADU OUTPUT CHECK. SELECT 1-3, AND PRESS START.
1.ADMEN1
2.ADMEN2
3.DGS
1
SIMULATION 9-1
ADU OUTPUT CHECK. EXECUTING···.
1.ADMEN1
2.ADMEN2
3.DGS
1
9-2
Purpose
Operation test/Check
Function
(Purpose)
(Purpose)
Used to check the operations of the sensors and
detectors in the duplex section and its control
circuit.
detectors in the duplex section and its control
circuit.
Section
Duplex
Item
Operation
ADUSET
ADU installation detection
DSW_D
ADU cabinet open detection
AINPD
ADU paper entry detection
APOD
ADU paper exit detection
APPD1
ADU paper detection 1
APPD2
ADU paper detection 2
10
10-1
Purpose
Operation test/Check
Function
(Purpose)
(Purpose)
Used to check the operations of the toner motor
and the related circuit.
and the related circuit.
Section
Process (Developing)
Item
Operation
1
Toner motor rotation start
2
Cancel (The display returns to the main code entry menu.)
Press [START] key.
Press [CUSTOM SETTINGS] key to
stop the operations. Or after 10sec.
stop the operations. Or after 10sec.
SIMULATION 9-2
ADU SENSOR CHECK.
ADUSET
DSW_D
AINPD APOD APPD1 APPD2
SIMULATION 10-1
TONER MOTOR ACTIVATION.
ARE YOU SURE?
1.YES
2.NO
2
SIMULATION 10-1
TONER MOTOR ACTIVATION. EXECUTING···.
1
AR-M351U/M451U, AR-M355U/M455U SIMULATION 9 - 17
Operation/Procedure
1) Select 1 (YES) with 10-key.
2) Press [START] key. (The trouble display is canceled.)
Operation/Procedure
1) Select 1 (YES) with 10-key.
2) Press [START] key. (The trouble display is canceled.)
Operation/Procedure
1) Select 1 (YES) with 10-key.
2) Press [START] key. (The trouble display is canceled.)
Operation/Procedure
1) Select 1 (YES) with 10-key.
2) Press [START] key. (The trouble display is canceled.)
13
13-0
Purpose
Clear/Cancel (Trouble etc.)
Function
(Purpose)
(Purpose)
Used to cancel the self-diag "U1" trouble. (Only
when FAX is installed.)
when FAX is installed.)
Section
FAX
Item
Trouble
1
YES
After canceling U1 trouble, the machine returns to
the main code entry standby mode.
the main code entry standby mode.
2
NO
Without canceling U1 trouble, the machine
returns to the main code entry standby mode.
returns to the main code entry standby mode.
14
14-0
Purpose
Clear/Cancel (Trouble etc.)
Function
(Purpose)
(Purpose)
Used to cancel excluding the self-diag U1/LCC/
U2/PF troubles.
U2/PF troubles.
Item
Trouble
Error
1
YES
After canceling the trouble other than U1, U2, PF,
and LCC, the machine returns to the main code
entry standby mode.
and LCC, the machine returns to the main code
entry standby mode.
2
NO
Without canceling the trouble, the machine returns
to the main code entry standby mode.
to the main code entry standby mode.
SIMULATION 13
U1 TROUBLE CANCELLATION.
ARE YOU SURE?
1. YES
2. NO
1
SIMULATION 14
TROUBLE CANCELLATION. (OTHERS)
ARE YOU SURE?
1. YES
2. NO
1
15
15-0
Purpose
Clear/Cancel (Trouble etc.)
Function
(Purpose)
(Purpose)
Used to cancel the self-diag "U6-01, 02, 03, F3-
12, 22" (large capacity paper feed tray, paper feed
trays 1, 2) troubles.
12, 22" (large capacity paper feed tray, paper feed
trays 1, 2) troubles.
Section
LCC
Item
Trouble
1
YES
After canceling the LCC trouble, the machine
returns to the main code entry standby mode.
returns to the main code entry standby mode.
2
NO
Without canceling the trouble, the machine
returns to the main code entry standby mode.
returns to the main code entry standby mode.
16
16-0
Purpose
Clear/Cancel (Trouble etc.)
Function
(Purpose)
(Purpose)
Used to cancel the self-diag U2 troubles.
Section
MFP control PWB, PCU PWB, scanner control
PWB
PWB
Item
Trouble
1
YES
After canceling the U2 trouble, the machine returns
to the main code entry standby mode.
to the main code entry standby mode.
2
NO
Without canceling the trouble, the machine returns
to the main code entry standby mode.
to the main code entry standby mode.
SIMULATION 15
LCC TROUBLE CANCELLATION.
ARE YOU SURE?
1. YES
2. NO
1
SIMULATION 16
U2 TROUBLE CANCELLATION.
ARE YOU SURE?
1. YES
2. NO
1
AR-M351U/M451U, AR-M355U/M455U SIMULATION 9 - 18
Operation/Procedure
1) Select 1 (YES) with 10-key.
2) Press [START] key. (The trouble display is canceled.)
Operation/Procedure
1) Enter the number corresponding to the maintenance timing
display.
2) Press [START] key. The condition entered in procedure 1) is
set.
Operation/Procedure
Various print counter values are displayed.
Operation/Procedure
The paper jam/trouble counter value is displayed.
17
17-0
Purpose
Clear/Cancel (Trouble etc.)
Function
(Purpose)
(Purpose)
Used to cancel the PF troubles (when the copy
inhibit command from the host computer is
received).
inhibit command from the host computer is
received).
Section
Communication unit (TEL/LIU/MODEM etc.)
Item
Trouble
Error
1
YES
After canceling the PF trouble, the machine returns
to the main code entry standby mode.
to the main code entry standby mode.
2
NO
Without canceling the trouble, the machine returns
to the main code entry standby mode.
to the main code entry standby mode.
21
21-1
Purpose
Setting
Function
(Purpose)
(Purpose)
Used to set the maintenance cycle.
Item
Specifications
Counter
Maintenance timing display
Set range
0
Default (Differs depending on the model.)
0 - 999
1 - 200
Maintenance display at 1K - 200K
999
No maintenance display
SIMULATION 17
PF TROUBLE CANCELLATION.
ARE YOU SURE?
1. YES
2. NO
1
SIMULATION 21-1
MAINTENANCE CYCLE SETUP. INPUT VALUE 0-999, AND PRESS
START.
0: DEFAULT
1-200: MAINTENANCE CYCLE (1K-200K)
999: FREE
0
22
22-1
Purpose
Adjustment/Setup/Operation data output/Check
(Display/Print)
(Display/Print)
Function
(Purpose)
(Purpose)
Used to check the print count value in each
section and each operation mode. (Used to check
the maintenance timing.)
section and each operation mode. (Used to check
the maintenance timing.)
Item
Counter
TOTAL
Total counter
DRUM
Drum counter
TONER
Toner counter
DEVE
Developer counter
MAINTENANCE
Maintenance counter
TOTAL OUTPUT
Total output quantity
COPIES
Copy effective paper counter
PRINTER
Printer counter
FAX
FAX print counter
I-FAX OUTPUT
iFAX print counter
DOC FILING OUTPUT
Document filing print counter
RIIGHT SIDE OUTPUT
Right paper exit counter
OTHERS
Other print counter (List print , etc.)
22-2
Purpose
Adjustment/Setup/Operation data output/Check
(Display/Print)
(Display/Print)
Function
(Purpose)
(Purpose)
Used to check the total numbers of misfeed and
troubles. (When the number of misfeed is
considerably great, it is judged as necessary for
repair. The misfeed rate is obtained by dividing
this count value with the total counter value.)
troubles. (When the number of misfeed is
considerably great, it is judged as necessary for
repair. The misfeed rate is obtained by dividing
this count value with the total counter value.)
Item
Trouble
PAPER JAM
Number of paper jams
SPF JAM
Number of SPF jams
TROUBLE
Number of troubles
SIMULATION 22-1
COUNTER DATA DISPLAY.
TOTAL: ******** DRUM: ******** TONER: ********
DEVE: ******** MAINTENANCE: ********
TOTAL OUTPUT: ******** COPIES: ********
PRINTER: ******** FAX OUTPUT: ********
I-FAX OUTPUT:******** DOC FILING OUTPUT:********
RIGHT SIDE:******** OTHERS: ********
SIMULATION 22-2
JAM/TROUBLE COUNTER DATA DISPLAY.
PAPER JAM: ******** SPF JAM: ********
TROUBLE: ********
AR-M351U/M451U, AR-M355U/M455U SIMULATION 9 - 19
Operation/Procedure
The history of paper jams and misfeed is displayed.
The misfeed history is displayed sequentially from the latest one.
The max. 100 items of misfeed history can be recorded. The data
may be used to identify trouble position.
The max. 100 items of misfeed history can be recorded. The data
may be used to identify trouble position.
The latest 100 items of paper jam history are displayed. (Refer to
the jam cause code table below.)
the jam cause code table below.)
(Jam cause code)
22-3
Purpose
Adjustment/Setup/Operation data output/Check
(Display/Print)
(Display/Print)
Function
(Purpose)
(Purpose)
Used to check misfeed positions and the misfeed
count of each position. (If the misfeed count is
considerably great, it may be judged as necessary
to repair.)
count of each position. (If the misfeed count is
considerably great, it may be judged as necessary
to repair.)
Section
Sections other than SPF/DSPF section
Item
Trouble
Misfeed
Code
Description
NO_JAM_CAUSE
No jam. Also used to cancel a jam.
TRAY2
Tray 2 paper feed jam
(MCPPD not-reaching: When AR-MU1
installed)
(TPFD1 not-reaching: When AR-D13
installed)
(DPFD1 not-reaching: When AR-D14
installed)
(MCPPD not-reaching: When AR-MU1
installed)
(TPFD1 not-reaching: When AR-D13
installed)
(DPFD1 not-reaching: When AR-D14
installed)
DPFD1_ND1
DPFD1 not-reaching jam (Desk tray 1 feed
paper)
paper)
DPFD1_ND2
DPFD1 not-reaching jam (Desk tray 2 feed
paper)
paper)
TPFD1_NTD
TPFD1 not-reaching jam (Tandem desk feed
paper)
paper)
MCPPD_ST2
MCPPD remaining jam (Machine tray 2 feed
paper: When AR-MU1 installed)
paper: When AR-MU1 installed)
TPFD1_ST2
TPFD1 not-reaching jam (Machine tray 2
feed paper: When AR-D13 installed)
feed paper: When AR-D13 installed)
DPFD1_ST2
TPFD1 not-reaching jam (Machine tray 2
feed paper: When AR-D13 installed)
feed paper: When AR-D13 installed)
DPFD1_SD1
DPFD1 remaining jam (Desk tray 1 feed
paper)
paper)
DPFD1_SD2
DPFD1 remaining jam (Desk tray 2 feed
paper)
paper)
TPFD1_STD
TPFD1 remaining jam (Tandem desk feed
paper)
paper)
PPD1NMF
PPD1 not-reaching jam (Manual feed tray
paper)
paper)
TRAY1
Tray 1 feed paper jam (PPD1 not-reaching)
PPD1NT2
PPD1 not-reaching jam (Machine tray 2
feed paper)
feed paper)
PPD1ND1
PPD1 not-reaching jam (Desk tray 1 feed
paper)
paper)
PPD1ND2
PPD1 not-reaching jam (Desk tray 2 feed
paper)
paper)
PPD1NTD
PPD1 not-reaching jam (Tandem desk feed
paper)
paper)
PPD1NAD
PPD1 not-reaching jam (ADU refeed paper)
PPD1SMF
PPD1 remaining jam (Manual feed tray feed
paper)
paper)
PPD1ST1
PPD1 remaining jam (Machine tray 1 feed
paper)
paper)
PPD1ST2
PPD1 remaining jam (Machine tray 2 feed
paper)
paper)
PPD1SD1
PPD1 remaining jam (Desk tray 1 feed
paper)
paper)
PPD1SD2
PPD1 remaining jam (Desk tray 2 feed
paper)
paper)
PPD1STD
PPD1 remaining jam (Tandem desk feed
paper)
paper)
PPD1SAD
PPD1 remaining jam (ADU refeed paper)
PPD1_PCU
PPD1 remaining jam (Timer end of fusing
ready standby/high voltage rising completion
standby, etc.)
ready standby/high voltage rising completion
standby, etc.)
PPD1PRI
PPD1 jam (Image ready is not supplied from
ICU.)
ICU.)
POD1N
POD1 not-reaching jam
POD1S
POD1 remaining jam
POD2N
POD2 not-reaching jam
POD2SR
POD2 remaining jam (When discharging to
the right side of machine.)
the right side of machine.)
POD2SL
POD2 remaining jam (When discharging to
the left side of machine.)
the left side of machine.)
AINPDN
ADU paper entry sensor not-reaching jam
AINPDS
ADU paper entry sensor remaining jam
APODN
ADU paper exit sensor not-reaching jam
APODS
ADU paper exit sensor remaining jam
APPD1N
ADU transport sensor 1 not-reaching jam
APPD1S
ADU transport sensor 1 remaining jam
APPD2N
ADU transport sensor 2 not-reaching jam
(When ADU transport)
(When ADU transport)
APPD2S
ADU transport sensor 2 remaining jam
(When ADU transport)
(When ADU transport)
BPT
Manual feed tray paper feed jam (APPD2
not-reaching)
not-reaching)
APPD2SM
ADU transport sensor 2 remaining jam
(Manual feed tray feed paper)
(Manual feed tray feed paper)
DESK2
Desk tray 2 paper feed jam (DPFD3 not
activated)
activated)
DPFD3SD2
DPFD3 remaining jam (Desk tray 2 feed
paper)
paper)
DESK1
Desk tray 1 paper feed jam (DPFD2 not
activated)
activated)
DPFD2N2
DPFD2 not-reaching jam (Desk tray 2 feed
paper)
paper)
DPFD2S1
DPFD2 remaining jam (Desk tray 1 feed
paper)
paper)
DPFD2S2
DPFD2 remaining jam (Desk tray 2 feed
paper)
paper)
TTRAY2
Tandem tray 2 paper feed jam (TPFD3 not
activated)
activated)
TPFD3S2
TPFD3 remaining jam (Tandem tray 2 feed
paper)
paper)
TTRAY1
Tandem tray 1 paper feed jam (TPFD2 not
activated)
activated)
TPFD2N2
TPFD2 not-reaching jam (Tandem tray 2
feed paper)
feed paper)
TPFD2S1
TPFD2 remaining jam (Tandem tray 1 feed
paper)
paper)
TPFD2S2
TPFD2 remaining jam (Tandem tray 2 feed
paper)
paper)
PPD1_DESK
DESK paper feed jam (Preliminary paper
feed from the desk, no response in a certain
time after paper feed instruction)
feed from the desk, no response in a certain
time after paper feed instruction)
FPID_N
Built-in finisher PID not-reaching jam
FPID_S
Built-in finisher PID remaining jam
FSCID_N
Built-in finisher SCID not-reaching jam
FSCID_S
Built-in finisher SCID remaining jam
FSCID2N
Built-in finisher SCID2 not-reaching jam
FSCID2S
Built-in finisher SCID2 remaining jam
FPPD_S
Built-in finisher PPD remaining jam
Code
Description
Click on the first or last page to see other AR-M351U / AR-M451U (serv.man17) service manuals if exist.