Sharp AR-M35 / AR-M450 (serv.man7) Handy Guide ▷ View online
Flash Upgrade Procedure
Version 2.0
Issue 01/02
31
SHARP ELECTRONICS (UK) LTD
DOCUMENT SYSTEMS SUPPORT
TECHNICAL SERVICES GROUP
TIGER PARALLEL UPDATE PROCEDURE
1 Set Tiger Control PWB jumpers as indicated on Page 37.
2 1) Turn on main switch.
2) "Boot Program Init. Please Wait"
3) "Version Check Conf : ××××"
4) Press menu key twice.
5) "Firm Update From Parallel"
6) Press OK button.
7) "Firm Update Waiting Data"
8) Drag the .sfu file to fcopy exe. (For the ARM350/450 there is now one firmware file to upgrade all the
firmware flash ROM's)
9) Display changes to "Firm Update Conf Writing Data"
10) Display changes to "Firm Update Result : OK"
11) Press OK button once.
12) Turn off main switch.
3 Reset the Tiger Control PWB jumpers to default settings
Firmware is updated.
CAUTION
:
Don't turn off the main switch until Display changes to "Firm Update Result : OK"
Flash Upgrade Procedure
Version 2.0
Issue 01/02
32
SHARP ELECTRONICS (UK) LTD
DOCUMENT SYSTEMS SUPPORT
TECHNICAL SERVICES GROUP
ARP350/450 Version
PRN-Control PWB
Function
Jumper switching function
The mark printed on PWB
SET
Default Setting
BOOT program start
DIAG
JP4
ON
OFF
Flash write (Control-PWB)
VCCW
JP2
H/off enable
L/On
protect
Flash write (PCU-PWB)
PCU-VCCW
JP6
H/Off enable
L/On
protect
ARM350/450 Version
MFP-Control PWB
Function
Jumper switching function
The mark printed on PWB
SET Default setting
BOOT program start
DIAG
JP5
ON
OFF
Flash write (Control-PWB)
VCCW
JP2
H/Off
enable
L/On
protect
Flash write (PCU-PWB)
PCU-VCCW
JP7
H/Off
enable
L/On
protect
Flash write (SCAN-PWB)
SCN-VCCW
JP3
H/Off
enable
L/On
protect
JP6
JP2
JP3
JP4
JP5
JP4
JP7
JP5
JP2
JP3
JP6
Flash Upgrade Procedure
Version 2.0
Issue 01/02
33
SHARP ELECTRONICS (UK) LTD
DOCUMENT SYSTEMS SUPPORT
TECHNICAL SERVICES GROUP
ARNC5J Flash Upgrade Procedure
There are two methods of upgrading the ARNC5J Network card:
•
SCVerup Utility
•
From DOS using FTP
SCVerup Utility is available from the Sharp Electronics Technical Web site. After starting the SCVerup utility from
the list of devices, highlight the machine or machines you wish to upgrade.
the list of devices, highlight the machine or machines you wish to upgrade.
Click on the “Browse” button and select the firmware file,
Click on the upload button, wait for the firmware upload to complete.
For Windows NT both TCP/IP & IPX protocols need to be running to support SCVERUP. If only TCP/IP protocol is
running, use ftp.
running, use ftp.
For upgrading using FTP command in DOS
1.
Go to MS-DOS prompt
2.
Change directory to that where binary file resides
3.
Enter ftp command
“ftp”
4.
From ftp prompt enter
“open IP address”
5.
For username key
admin
6.
For password key
Sharp
7.
At prompt key
“bin”
8.
Then send binary file
“put filename.bin”
9.
When completed type
“bye”
10.
Power cycle the copier
Firmware History
Version 2.0
Issue 01/02
34
SHARP ELECTRONICS (UK) LTD
DOCUMENT SYSTEMS SUPPORT
TECHNICAL SERVICES GROUP
TIGER (M) FIRMWARE
Last Update
Apr-02
ARM350/450
Main Boot PCU Scan
Revision/Correction
Made
Production
V4.10 V1.08 V2.12 V2.00 Previously, the machine became inoperative when printing a
mixed document of envelope, postcard and regular sized paper as
the machine requested for postcard/envelope when printing
regular sized paper. This failure is fixed in this version. Previously,
the machine did not recover from auto-shut off mode. This failure
is fixed in this version. The message to say not to turn off the
power at the time of paper jamming is added. Previously, the pop-
up message “out-of paper” appeared from S-MON when
recovering from shut-off mode. This failure is fixed in this version.
the machine requested for postcard/envelope when printing
regular sized paper. This failure is fixed in this version. Previously,
the machine did not recover from auto-shut off mode. This failure
is fixed in this version. The message to say not to turn off the
power at the time of paper jamming is added. Previously, the pop-
up message “out-of paper” appeared from S-MON when
recovering from shut-off mode. This failure is fixed in this version.
June01
V5.09 V2.01 V3.01 V3.02 AR-FN7 “High speed stacking mode” is added to Key Operator
Program previously, the machine locked up if starting to use the
machine right after clearing a DF-jam. This failure is fixed in this
version. Previously, a paper jam between the ADU and the main
unit could not be cleared without opening/closing the left cover
twice. This failure is fixed in this version. Access from the web
page on the Image Send Screen is made possible by a fix. A
change is made to delete an email destination after sending e-mail
if the e-mail destination is highlighted but the “Enable Hyperlink to
FTP server to be e-mailed” check box is unchecked.
machine right after clearing a DF-jam. This failure is fixed in this
version. Previously, a paper jam between the ADU and the main
unit could not be cleared without opening/closing the left cover
twice. This failure is fixed in this version. Access from the web
page on the Image Send Screen is made possible by a fix. A
change is made to delete an email destination after sending e-mail
if the e-mail destination is highlighted but the “Enable Hyperlink to
FTP server to be e-mailed” check box is unchecked.
July01
V6.06 V2.01A V3.04 V4.00 A change is made for compatibility with AR-PF1. Sim.46-26 is
added. (0 = Pattern matching function ON 1= Pattern matching
function OFF).
function OFF).
Aug01
V6.06 V2.01A V3.06 V4.00 The message “Copying” was indicated and the machine hung up.
This failure is corrected. The default value of Sim.46-26 (Pattern
Matching Function when the fax data is sent.) the value is changed
to ‘0’ (the pattern matching function is available).
Matching Function when the fax data is sent.) the value is changed
to ‘0’ (the pattern matching function is available).
Sept01
V8.12 V2.01B V5.00 V5.00 Image Send function is improved and the following function is
added in order to improve the operation. The file transmission
function in TIFF format is added. (It is possible for the user to
select this function when the checkbox is ticked.) If the checkbox
is off when the receiver on FTP is selected, the receiver selected
when submitted can be cleared. The detailed information about
the error code is mentioned in Help on Web page. The resolution
(dpi) is indicated in Help on Web page. The file format can be
selected every time the image is sent. The rotate-sorting function
setting is available in Key OP (Checkbox On/Off). The font list
printing function is added on AR-PF1. The support for binary mode
is added. When the NC5J is installed, CE-00 trouble is
experienced. This failure is eliminated. (It is possible to reduce the
CE-00 trouble if SW80-8 of Sim.66-1 is set as “1”.) The number of
pages with memory full in Mass Original mode (special function)
did not match to the number of pages with memory full in.
function in TIFF format is added. (It is possible for the user to
select this function when the checkbox is ticked.) If the checkbox
is off when the receiver on FTP is selected, the receiver selected
when submitted can be cleared. The detailed information about
the error code is mentioned in Help on Web page. The resolution
(dpi) is indicated in Help on Web page. The file format can be
selected every time the image is sent. The rotate-sorting function
setting is available in Key OP (Checkbox On/Off). The font list
printing function is added on AR-PF1. The support for binary mode
is added. When the NC5J is installed, CE-00 trouble is
experienced. This failure is eliminated. (It is possible to reduce the
CE-00 trouble if SW80-8 of Sim.66-1 is set as “1”.) The number of
pages with memory full in Mass Original mode (special function)
did not match to the number of pages with memory full in.
Oct01
V9.07 V3.02 V6.04 V5.02 The maintenance cycle setting was changed as follows: DEFAULT
(50K) / 5K / 10K / 25K / 50K / 80K / FREE. Sim26-38 is added for
MFP model. The machine does not stop if the number of copies
reaches to the setting for the maintenance cycle + 10%.1 (PRINT
STOP): The machine stops if the number of copies reaches to the
setting for the maintenance cycle +10%.
MFP model. The machine does not stop if the number of copies
reaches to the setting for the maintenance cycle + 10%.1 (PRINT
STOP): The machine stops if the number of copies reaches to the
setting for the maintenance cycle +10%.
Dec01
Click on the first or last page to see other AR-M35 / AR-M450 (serv.man7) service manuals if exist.