Sharp AR-M35 / AR-M450 (serv.man12) Service Manual ▷ View online
AR-M350 SIMULATIONS 10-9
5. Details of simulations
<List of set values>
<List of display value>
<List of set values>
<List of display values>
Main code 1
1-1
Purpose
Operation test, check
Function (Content)
Used to check the operations of the scanner
(reading) unit and its control circuit.
(reading) unit and its control circuit.
Section
Scanner (reading)
Item
Operation
Operation/Procedure Select with 10 digit key pad.
1
High speed operation
168mm / sec
2
Middle speed operation
110mm / sec
3
Low speed operation
55mm / sec
4
Top speed operation
220mm / sec
1-2
Purpose
Operation test, check
Function (Content)
Used to check the operations of the sensors and
detectors in the scanner (reading) unit and their
control circuits.
detectors in the scanner (reading) unit and their
control circuits.
Section
Scanner (reading)
Item
Operation
Operation/Procedure The sensor display is highlighted when it is
detected.
MHPS
Optical system home position
SIMULATION 1-1
SCANNER CHECK. SELECT 1-4, AND PRESS START.
1. HIGH SPEED
2. MIDDLE SPEED
3. LOW SPEED
4. TOP SPEED
SCANNER CHECK. SELECT 1-4, AND PRESS START.
1. HIGH SPEED
2. MIDDLE SPEED
3. LOW SPEED
4. TOP SPEED
1
SIMULATION 1-1
SCANNER CHECK. EXECUTING...
1. HIGH SPEED
2. MIDDLE SPEED
3. LOW SPEED
4. TOP SPEED
SCANNER CHECK. EXECUTING...
1. HIGH SPEED
2. MIDDLE SPEED
3. LOW SPEED
4. TOP SPEED
1
Press [START] key to get started.
Press [CUSTOM SETTING] key to stop.
Stops when scan is completed.
SIMULATION 1-2
SCANNER SENSOR CHECK..
SCANNER SENSOR CHECK..
MHPS
Main code 2
2-1
Purpose
Operation test, check
Function (Content)
Used to check the operations of the automatic
document feeder unit and its control circuit.
document feeder unit and its control circuit.
Section
DSPF
Item
Operation
Operation/Procedure Select with 10 digit key pad.
1
High speed operation
2
Low speed operation
2-2
Purpose
Operation test, check
Function (Content)
Used to check the operations of the sensors and
detectors in the automatic document feeder unit
and their control circuits.
detectors in the automatic document feeder unit
and their control circuits.
Section
DSPF
Item
Operation
Operation/Procedure The sensor display is highlighted when it is
detected.
SSET
SPF sensor
SOCD
Open sensor
SCOV
Paper feed cover sensor
SDD
Document set sensor
SPSD
Document resist front sensor
SPCD
Document exit sensor
SWDn
Document width sensor (n
1(Inside) ~6(Outside))
SLDn
Document length sensor (n
1(Inside) ~2(Outside))
OSSET
OS installation sensor
STSET
Stamp unit installation sensor
SWD_LEN SPF guide plate position (Unit: 0.1mm)
SWD_AD
SWD_AD
SPF document width detection volume output AD value
SIMULATION 2-1
SPF AGING TEST. SELECT 1-2, AND PRESS START.
1. HIGH SPEED
2. LOW SPEED
SPF AGING TEST. SELECT 1-2, AND PRESS START.
1. HIGH SPEED
2. LOW SPEED
2
SIMULATION 2-1
SPF AGING TEST. EXECUTING...
1. HIGH SPEED
2. LOW SPEED
SPF AGING TEST. EXECUTING...
1. HIGH SPEED
2. LOW SPEED
2
Press [START] key to get started.
Press [CUSTOM SETTING] key to stop.
SIMULATION 2-2
SPF SENSOR CHECK.
SPF SENSOR CHECK.
SSET
SOCD
SCOV
SDD
SPSD
SPOD
SWD6
SWD5
SWD4
SWD3
SWD2
SWD1
SLD2
SLD1
CISSET
STSET
SWD_LEN: 2100
SWD_AD: 600
SDD
SPSD
SPOD
SWD5
SWD4
SWD3
SWD2
SWD1
SLD2
SLD1
STSET
SWD_LEN:
SWD_AD:
- !"#$%&
AR-M350 SIMULATIONS 10-10
<List of set values>
<List of display values>
2-3
Purpose
Operation test, check
Function (Content)
Used to check the operation under load in the
automatic document feeder unit and their control
circuits.
automatic document feeder unit and their control
circuits.
Section
DSPF
Item
Operation
Operation/Procedure Select with 10 digit key pad.
1
Motor high speed rotation
2
Motor low speed rotation
3
Document stopper solenoid
4
Document feed solenoid
5
Document feed clutch
6
Document resist clutch
7
Stamp solenoid
SIMULATION 2-3
SPF LOAD TEST. SELECT 1-7, AND PRESS START.
1. MOTOR(H) 2. MOTOR(L)
3. SDSS 4. SPFS
SPF LOAD TEST. SELECT 1-7, AND PRESS START.
1. MOTOR(H) 2. MOTOR(L)
3. SDSS 4. SPFS
5. SPFC 6. SPSC 7. STMPS
2
SIMULATION 2-3
SPF LOAD TEST. EXECUTING...
1. MOTOR(H) 2. MOTOR(L)
3. SDSS 4. SPFS
SPF LOAD TEST. EXECUTING...
1. MOTOR(H) 2. MOTOR(L)
3. SDSS 4. SPFS
5. SPFC 6. SPSC 7. STMPS
2
Press [START] key to get started.
Press [CUSTOM SETTING] key to stop.
Main code 3
3-2
Purpose
Operation test, check
Function (Content)
Used to check the operations of the sensors and
detectors in the finisher and their control circuits.
detectors in the finisher and their control circuits.
Section
Finisher
Item
Operation
Operation/Procedure The display is highlighted when detected.
Finisher
Console finisher
STHP
Stapler HP detection
FSSS
Stapler safety switch
POD
Tray 2 paper exit detection
FJS
Joint switch
SCID
Staple compiler paper entry
detection
detection
FFDSW Front door switch
PID
Paper entry detection
FTCS
Upper cover sensor
T2PD
Tray 2 paper empty detection
FFDS
Front door sensor
T2DN
Tray 2 lower limit detection
FSPS
Self prime sensor
T2UP
Tray 2 upper limit detection
FSUC
Stapler connection detection
JRHP
Jogger R HP
FSS
Staple sensor
JFHP
Jogger (F) HP
FSTHPS Stapler HP sensor
SCID2
Staple compiler paper entry
detection 2
detection 2
FSHPS
Slide HP sensor
STTHP2 Staple rotation HP detection 2
FLE
Lift lock sensor
STTHP1 Staple rotation HP detection 1
FLLLS
Lift lower limit sensor
STUHP
Staple shift HP detection
FULS
Lift upper limit sensor
PSHP
Pusher HP detection
FFE
Bookbinding clock sensor
PPD
Paper hold return detection
FFES
Bookbinding paper sensor
DSW2
Staple replacement door open
detection
detection
FFRHPS Bookbinding roller HP sensor
DSW1
Compiler jam cancel door open
detection
detection
FFHPS
Bookbinding HP sensor
24VM
24V power supply
FFPS
Bookbinding position sensor
T1PF
Tray 1 full detection
FSLS
Paper surface sensor
STSP
Stapling ready detection
FBES
Tray paper sensor
STLS
Cartridge inside spare staple
empty detection
empty detection
FOBHPS Paper exit belt HP sensor
STNC
Cartridge empty detection
FAS
Alignment tray sensor
DOPD
Interface unit door open
detection
detection
FRJHPS Alignment HP sensor R
MMLK
Main drive motor lock detection
FFJHPS Alignment HP sensor F
SCPD
Staple compiler paper empty
detection
detection
FARHPS Bundle roller HP sensor
FPHPS
Paddle HP sensor
FES
Entry port sensor
SIMULATION 3-2
FINISHER SENSOR CHECK.
PID
FINISHER SENSOR CHECK.
PID
SCID
SCID2
PPD
SCPD
POD
T1PF
T2UP
T2DN
T2PD
STSP
STLS
STNC
STHP
JFHP
JRHP
PSHP
STUHP
XXXX
STTHP1
STTHP2
DOPD
DSW1
DSW2
24VM
MMLK
Finisher (AR-FN6)
Console finisher (AR-FN7)
SIMULATION 3-2
FINISHER SENSOR CHECK.
FSSS
FINISHER SENSOR CHECK.
FSSS
FJS
FFDSW
FTCS
FFDS
FSPS
FSUC
FSS
FSTHPS FSHPS FLE
FLLLS
FULS
FFE
FFES
FFRHPS FFHPS FFPS
FSLS
FBES
FOBHPS FAS
FRJHPS FFJHPS FARHPS FPHPS
FES
(FPE)
(FPE)
(FPSHPS) (FPUC)
(FPDS) (FPDSS4) (FPDSS3) (FPDSS2)
(FPDSS1) (FPTS)
Devices in ( ) are added when the punch unit is installed.
!"#$%&
AR-M350 SIMULATIONS 10-11
•The following units are added when the punch unit is installed to the
console finisher:
<List of display values>
(Stored on PCU PWB)
<List of set values>
(Values stored in EEPROM)
FPE
Punch motor encoder
FPSHPS
Punch side register HP
FPUC
Punch connection detection
FPDS
Punch dust sensor
FPDSS4
Punch side register sensor 4
FPDSS3
Punch side register sensor 3
FPDSS2
Punch side register sensor 2
FPDSS1
Punch side register sensor 1
FPTS
Punch timing sensor
3-3
Purpose
Operation test, check
Function (Content)
Used to check the operation under load in the
finisher and their control circuits.
finisher and their control circuits.
Section
Finisher
Item
Operation
Operation/Procedure The display is highlighted when detected.
Finisher
Console finisher
1 T2S
Tray 2 solenoid
1 FFC
Folding clutch
2 T2OM Paper exit motor
2 FPSM Puncher side register
motor
3 SPS
Stopper solenoid
3 FPNM Punch motor
4 SCRS Roller pressure
release solenoid
4 FLM
Shift motor
5 PPS
Rear edge h folding
solenoid
solenoid
5 FFSM Stapler motor
6 SCGS Compiler gate
solenoid
6 FSM
Slide motor
7 STTM Staple rotation motor
7 FRJM Alignment motor R
8 STUM Stapler shift motor
8 FFJM
Alignment motor F
9 MM
Main drive motor
9 FAM
Bundle exit motor
10 EVM
Elevator motor
10 FPM
Paddle motor
11 STM
Staple motor
11 FFM
Transport motor
12 JRM
Jogger motor rear
13 JFM
Jogger motor front
14 PSM
Pusher motor
SIMULATION 3-3
FINISHER LOAD TEST. SELECT 1- , AND PRESS START.
FINISHER LOAD TEST. SELECT 1- , AND PRESS START.
2
SIMULATION 3-3
FINISHER LOAD TEST. EXECUTING...
FINISHER LOAD TEST. EXECUTING...
2
Press [START] key to get started.
Press [CUSTOM SETTING] key to stop.
3-6
Purpose
Adjustment
Function (Content)
Used to adjust the stacking capacity of the
finisher (AR-FN6). (Used to adjust the alignment
plate (jogger) stop position in the finisher paper
width direction. The adjustment is made by
changing the alignment plate home position in
the paper width direction by software. )
finisher (AR-FN6). (Used to adjust the alignment
plate (jogger) stop position in the finisher paper
width direction. The adjustment is made by
changing the alignment plate home position in
the paper width direction by software. )
Section
Finisher
Item
Operation
Operation/Procedure Enter the adjustment value with 10 digit key pad
and press START key. The jogger moves to LT
position (Inch series) or A4 position (AB series)
according to the entered value, and stops there.
position (Inch series) or A4 position (AB series)
according to the entered value, and stops there.
3-10
Purpose
Adjustment
Function (Content)
Used to adjust the console finisher (AR-FN7).
Section
Finisher
Item
Operation
Operation/Procedure Setting of the console finisher is performed.
Adjustment content
Range
Initial
value
1STEP
1 Saddle binding position adjustment
0~400
200 0.0707mm
2 Saddle folding position adjustment
0~400
200 0.0525mm
3 Front alignment position adjustment
0~20
10
0.367mm
4 Rear alignment position adjustment
0~20
10
0.367mm
5 Staple rear one-position binding position adjustment
0~200
100 0.04374mm
6 Staple front one-position binding position adjustment 0~200
100 0.04374mm
7 Staple 2-position binding center adjustment
0~200
100 0.04374mm
8 Staple 2-position binding pitch adjustment
0~99
50
0.04374mm
9 Punch center adjustment (Slide direction)
47~53
50
1mm
10 Punch hole position adjustment (Paper feed direction) 0~99
50
0.105mm
SIMULATION 3-6
FINISHER JOGGER ADJUSTMENT. INPUT VALUE 40-60, AND PRESS START.
FINISHER JOGGER ADJUSTMENT. INPUT VALUE 40-60, AND PRESS START.
50
SIMULATION 3-6
FINISHER JOGGER ADJUSTMENT. MOVING...
FINISHER JOGGER ADJUSTMENT. MOVING...
50
Press [START] key to get started.
Press [CUSTOM SETTING] key to stop.
Stops when the operation is terminated.
SIMULATION 3-10
CONSOLE FINISHER SETTING. SELECT 1-10, AND PRESS START.
1. SADDLE POSITION 2. FOLDING POSITION
3. FRONT ADJUST
4. REAR ADJUST
CONSOLE FINISHER SETTING. SELECT 1-10, AND PRESS START.
1. SADDLE POSITION 2. FOLDING POSITION
3. FRONT ADJUST
4. REAR ADJUST
5. STAPLE REAR
6. STAPLE FRONT
7. STAPLE BOTH
8. STAPLE PITCH
9. PUNCH CENTER
10. PUNCH HOLE
1
SIMULATION 3-10
CONSOLE FINISHER SETTING. INPUT VALUE, AND PRESS START.
1. FOLDING POSITION
CONSOLE FINISHER SETTING. INPUT VALUE, AND PRESS START.
1. FOLDING POSITION
200
Press [START] key to get started.
Press [CUSTOM SETTING] key to stop.
!"#$%&
AR-M350 SIMULATIONS 10-12
<List of display values>
<List of set values>
<List of display values>
3-20
Purpose
Operation test, check
Function (Content)
Used to check the mail bin stacker (AR-MS1)
sensor.
sensor.
Section
Mail bin stacker
Item
Operation
Operation/Procedure The display is highlighted when detected.
MPFD1 Tray 1 paper full detection MPPD1 Paper transport sensor 1
MPFD2 Tray 2 paper full detection MPPD2 Paper transport sensor 2
MPFD3 Tray 3 paper full detection MPPD3 Paper transport sensor 3
MPFD4 Tray 4 paper full detection MPPD4 Paper transport sensor 4
MPFD5 Tray 5 paper full detection MPPD5 Paper transport sensor 5
MPFD6 Tray 6 paper full detection M24VM 24V power supply
MPFD7 Tray 7 paper full detection MDD1
MPFD2 Tray 2 paper full detection MPPD2 Paper transport sensor 2
MPFD3 Tray 3 paper full detection MPPD3 Paper transport sensor 3
MPFD4 Tray 4 paper full detection MPPD4 Paper transport sensor 4
MPFD5 Tray 5 paper full detection MPPD5 Paper transport sensor 5
MPFD6 Tray 6 paper full detection M24VM 24V power supply
MPFD7 Tray 7 paper full detection MDD1
Jam cancel door
MPFD8 Tray 8 paper full detection MDOPD Interface unit door
MPID
MPID
Interface unit paper entry
detection
detection
3-21
Purpose
Operation test, check
Function (Content)
Used to check the operations of the mail bin
stacker loads.
stacker loads.
Section
Mail bin stacker
Item
Operation
Operation/Procedure Select with 10 digit key pad.
1
Main motor
2
Gate solenoid 1
3
Gate solenoid 2
4
Gate solenoid 3
5
Gate solenoid 4
6
Gate solenoid 5
7
Gate solenoid 6
8
Gate solenoid 7
SIMULATION 3-20
MAIL BOX SENSOR CHECK.
MPFD1 MPFD2 MPFD3 MPFD4 MPFD5 MPFD6 MPFD7
MPFD8 MPID
MAIL BOX SENSOR CHECK.
MPFD1 MPFD2 MPFD3 MPFD4 MPFD5 MPFD6 MPFD7
MPFD8 MPID
MPPD1 MPPD2 MPPD3 MPPD4 MPPD5
M24VM MDD1
MDOPD
MPFD1
SIMULATION 3-21
MAIL BOX LOAD TEST. SELECT 1-8, AND PRESS START.
1.MM
2.GSOL1
3.GSOL2
4.GSOL3
5.GSOL4
6.GSOL5
7.GSOL6
8.GSOL7
MAIL BOX LOAD TEST. SELECT 1-8, AND PRESS START.
1.MM
2.GSOL1
3.GSOL2
4.GSOL3
5.GSOL4
6.GSOL5
7.GSOL6
8.GSOL7
2
SIMULATION 3-21
MAIL BOX LOAD TEST. EXECUTING...
1.MM
2.GSOL1
3.GSOL2
4.GSOL3
5.GSOL4
6.GSOL5
7.GSOL6
8.GSOL7
MAIL BOX LOAD TEST. EXECUTING...
1.MM
2.GSOL1
3.GSOL2
4.GSOL3
5.GSOL4
6.GSOL5
7.GSOL6
8.GSOL7
2
Press [START] key to get started.
Press [CUSTOM SETTING] key to stop.
Main code 4
4-2
Purpose
Operation test, check
Function (Content)
Used to check the operations of the sensors and
detectors in the paper feed section (desk paper
feed/large capacity trays) and their control
circuits.
detectors in the paper feed section (desk paper
feed/large capacity trays) and their control
circuits.
Section
Paper feed
Item
Operation
Operation/Procedure The display is highlighted when detected.
3-tray desk
LCC
DDRS
Desk door sensor
TDRS
Tandem side door sensor
DSPD2
Desk cassette 2
remaining paper quantity
sensor
remaining paper quantity
sensor
TTSD
Tandem tray sensor
DSPD1
Desk cassette 1
remaining paper quantity
sensor
remaining paper quantity
sensor
TLUD2
Tandem tray 2
upper limit sensor
upper limit sensor
DCSS24
Desk cassette 2
paper rear edge sensor 4
paper rear edge sensor 4
TLUD1
Tandem tray 1
upper limit sensor
upper limit sensor
DCSS23
Desk cassette 2
paper rear edge sensor 3
paper rear edge sensor 3
TSPD2
Tandem tray 2
remaining quantity sensor
remaining quantity sensor
DCSS22
Desk cassette 2
paper rear edge sensor 2
paper rear edge sensor 2
TSPD1
Tandem tray 1
remaining quantity sensor
remaining quantity sensor
DCSS21
Desk cassette 2
paper rear edge sensor 1
paper rear edge sensor 1
TPED2
Tandem tray 2
paper sensor
paper sensor
DLUD2
Desk cassette 2
upper limit sensor
upper limit sensor
TPED1
Tandem tray 1
paper sensors
paper sensors
DPED2
Desk cassette 2
paper sensor
paper sensor
TPFD3
Tandem paper transport
sensor 3
sensor 3
DPFD3
Desk paper transport
sensor 3
sensor 3
TPFD2
Tandem paper transport
sensor 2
sensor 2
DCSS14
Desk cassette 1
paper rear edge sensor 4
paper rear edge sensor 4
MCSS4
MP tray size detection 4
DCSS13
Desk cassette 1
paper rear edge sensor 3
paper rear edge sensor 3
MCSS3
MP tray size detection 3
DCSS12
Desk cassette 1
paper rear edge sensor 2
paper rear edge sensor 2
MCSS2
MP tray size detection 23
DCSS11
Desk cassette 1
paper rear edge sensor 1
paper rear edge sensor 1
MCSS1
MP tray size detection 1
DLUD1
Desk cassette 1
upper limit sensor
upper limit sensor
MCSPD
MP tray remaining quantity
detection
detection
DPED1
Desk cassette 1
paper sensor
paper sensor
MCLUD
MP tray upper limit
detection
detection
DPFD2
Desk paper transport
sensor 2
sensor 2
MCPED
MP tray paper empty
detection
detection
MCSS4
MP tray size detection 4
TPFD1
MP tray transport detection
SIMULATION 4-2
DESK SENSOR CHECK.
DDRS
DESK SENSOR CHECK.
DDRS
DPFD1
DPFD2
DPFD3
MCLUD
DLUD1
DLUD2
MCSPD
DSPD1
DSPD2
MCPED
DPED1
DPED2
MCSS1
MCSS2
MCSS3
MCSS4
DCSS11
DCSS12
DCSS13
DCSS14
XXXXXX DCSS21
DCSS22
DCSS23
DCSS24
XXXXXX
SIMULATION 4-2
LCC SENSOR CHECK.
TDRS
LCC SENSOR CHECK.
TDRS
TTSD
TPFD1
TPFD2
TPFD3
MCLUD
TLUD1
TLUD2
MCSPD
TSPD1
TSPD2
MCPED
TPED1
TPED2
MCSS1
MCSS2
MCSS3
MCSS4
(3-tray desk)
(LCC)
' !"#$%&
Click on the first or last page to see other AR-M35 / AR-M450 (serv.man12) service manuals if exist.