AR-M160 (serv.man23). Procedure for installation of Pegasus series download drivers. Document describes procedure for installing USB drivers prior to firmware downloading. — Sharp Copying Equipment FAQ (repair manual)

Model
AR-M160 (serv.man23)
Pages
3 Few pages! See other manuals at the bottom of the first or last page.
Size
17.45 KB
Type
PDF
Document
FAQ
Brand
Device
Copying Equipment / Procedure for installation of Pegasus series download drivers. Document describes procedure for installing USB drivers prior to firmware downloading.
File
ar-m160-sm23.pdf
Date

View Sharp AR-M160 (serv.man23) FAQ online

Procedure for installation of USB Download drivers,
for Pegasus – series machines
Installation of USB download driver for Windows 2000
1.  Put the copier in to download mode. This can be done either by use of
Simulation 49-01, or by switching the copier on whilst holding down the
‘AUDIT CLEAR’ and ‘ZOOM’ keys. When the copier is in download mode,
the ‘d’ symbol will be visible in the copier’s counter display.
2.  Connect an ‘A to B’ type USB cable between the PC’s USB port and the
copier’s USB1.1 port. If the copier has an optional USB2.0 port, do not
connect the USB cable to this port.
3.  Boot the PC, and on entering Windows the ‘Found new hardware’ wizard
will identify ‘DOWNLOAD’ as a new device.
4. Click ‘Next’, and select ‘Search for a suitable driver for my device
(recommended)’. Click ‘Next’.
5.  Ensure only ‘Specify a location’ is checked, and then click ‘Next’.
6.  Click ‘Browse’, navigate to ‘2kXp’ folder in ‘USB download drivers’ folder,
and then select the ‘Pegasus.inf’ file. Click ‘Open’, and then click ‘OK’.
7.  The ‘Found a driver for this device’ message will appear on the screen.
Confirm that the path to the driver shown is correct, and then click ‘Next’.
8.  Windows confirms installation of ‘Maintenance Tool Version 4.00 Generic
USB Driver’ is complete. Click ‘Finish’ to close the wizard.
9.  To check that installation of the USB download driver was completed
successfully, click ‘Start’ – ‘Settings’ – ‘Control panel’ – ‘System’. Expand
‘Universal Serial Bus Controllers’, and confirm that the ‘Maintenance Tool
Version 4.00 Generic USB Driver’ is listed. It will now be possible to run
the Maintenance program.
Installation of USB download driver for Windows XP
1.  Put the copier in to download mode. This can be done either by use of
Simulation 49-01, or by switching the copier on whilst holding down the
‘AUDIT CLEAR’ and ‘ZOOM’ keys. When the copier is in download mode,
the ‘d’ symbol will be visible in the copier’s counter display.
2. Connect an ‘A to B’ type USB cable between the PC’s USB port and the
copier’s USB1.1 port. If the copier has an optional USB2.0 port, do not
connect the USB cable to this port.
3.  Boot the PC, and on entering Windows the ‘Found new hardware’ wizard
will identify ‘DOWNLOAD’ as a new device. In the wizard, select ‘Install
from a list or specific location (advanced)’, and click ‘Next’.
4. Ensure the ‘Search for the best drivers in these locations’ radio button is
selected, and that ‘Include this location in the search’ is the only box
checked.
5. Click ‘Browse’, and navigate to the ‘2kXp’ folder. Click ‘OK’.
6. Click ‘Next’, and Windows finds ‘Maintenance Tool Version 4.00 Generic
USB Driver’. Click  ‘Continue anyway’ if the Windows Logo Testing box
appears.
7.  When installation is complete, click ‘Finish’ to close the wizard.
8.  To check that installation of the USB download driver was completed
successfully, open ‘Control panel’, ‘System’. Click the ‘Hardware’ tab and
then the ‘Device manager’ tab. Expand ‘Universal Serial Bus Controllers’,
and confirm that the ‘Maintenance Tool Version 4.00 Generic USB Driver’
is listed. It will now be possible to run the Maintenance program.
Installation of USB download driver for Windows ’98 / ME
1.  Put the copier in to download mode. This can be done either by use of
Simulation 49-01, or by switching the copier on whilst holding down the
‘AUDIT CLEAR’ and ‘ZOOM’ keys. When the copier is in download mode,
the ‘d’ symbol will be visible in the copier’s counter display.
2. Connect an ‘A to B’ type USB cable between the PC’s USB port and the
copier’s USB1.1 port. If the copier has an optional USB2.0 port, do not
connect the USB cable to this port.
3.  Boot the PC, and on entering Windows the ‘Found new hardware’ wizard
will identify ‘DOWNLOAD’ as a new device. In the wizard, click ‘Next’.
4. Select ‘Search for the best driver for your hardware’, and then click ‘Next’.
5. Ensure that ‘Specify a location’ is ticked, and then browse to the
‘Win9xME’ folder.
6. Click ‘Next’, and then click ‘Finish’ to complete the installation.
7. Check that installation of the USB download driver was completed
successfully, by opening ‘Control panel’ and then ‘System’. Click the
‘Device manager’ tab, and expand ‘Universal Serial Bus Controllers’.
Confirm that the ‘Maintenance Tool Version 4.00 Generic USB Driver’ is
listed. It will now be possible to run the Maintenance program.
For details on using the Maintenance program to download firmware to
the copier, refer to the ‘Using the Pegasus – series Maintenance
Program’ guide.
Installation of USB download driver for Windows ’98 / ME
1.  Put the copier in to download mode. This can be done either by use of
Simulation 49-01, or by switching the copier on whilst holding down the
‘AUDIT CLEAR’ and ‘ZOOM’ keys. When the copier is in download mode,
the ‘d’ symbol will be visible in the copier’s counter display.
2. Connect an ‘A to B’ type USB cable between the PC’s USB port and the
copier’s USB1.1 port. If the copier has an optional USB2.0 port, do not
connect the USB cable to this port.
3.  Boot the PC, and on entering Windows the ‘Found new hardware’ wizard
will identify ‘DOWNLOAD’ as a new device. In the wizard, click ‘Next’.
4. Select ‘Search for the best driver for your hardware’, and then click ‘Next’.
5. Ensure that ‘Specify a location’ is ticked, and then browse to the
‘Win9xME’ folder.
6. Click ‘Next’, and then click ‘Finish’ to complete the installation.
7. Check that installation of the USB download driver was completed
successfully, by opening ‘Control panel’ and then ‘System’. Click the
‘Device manager’ tab, and expand ‘Universal Serial Bus Controllers’.
Confirm that the ‘Maintenance Tool Version 4.00 Generic USB Driver’ is
listed. It will now be possible to run the Maintenance program.
For details on using the Maintenance program to download firmware to
the copier, refer to the ‘Using the Pegasus – series Maintenance
Program’ guide.
Installation of USB download driver for Windows ’98 / ME
1.  Put the copier in to download mode. This can be done either by use of
Simulation 49-01, or by switching the copier on whilst holding down the
‘AUDIT CLEAR’ and ‘ZOOM’ keys. When the copier is in download mode,
the ‘d’ symbol will be visible in the copier’s counter display.
2. Connect an ‘A to B’ type USB cable between the PC’s USB port and the
copier’s USB1.1 port. If the copier has an optional USB2.0 port, do not
connect the USB cable to this port.
3.  Boot the PC, and on entering Windows the ‘Found new hardware’ wizard
will identify ‘DOWNLOAD’ as a new device. In the wizard, click ‘Next’.
4. Select ‘Search for the best driver for your hardware’, and then click ‘Next’.
5. Ensure that ‘Specify a location’ is ticked, and then browse to the
‘Win9xME’ folder.
6. Click ‘Next’, and then click ‘Finish’ to complete the installation.
7. Check that installation of the USB download driver was completed
successfully, by opening ‘Control panel’ and then ‘System’. Click the
‘Device manager’ tab, and expand ‘Universal Serial Bus Controllers’.
Confirm that the ‘Maintenance Tool Version 4.00 Generic USB Driver’ is
listed. It will now be possible to run the Maintenance program.
For details on using the Maintenance program to download firmware to
the copier, refer to the ‘Using the Pegasus – series Maintenance
Program’ guide.

Download Sharp AR-M160 (serv.man23) FAQ

Here you can view online or download Sharp AR-M160 (serv.man23) FAQ in pdf. This FAQ can help you recover, restore, fix, disassemble and repair Sharp AR-M160 (serv.man23) Copying Equipment. Information contained in Sharp AR-M160 (serv.man23) service manual (repair manual) typically includes:

  • Disassembly, troubleshooting, programming, maintenance, remote, adjustment, installation and setup instructions.
  • Schematics, wiring and block diagrams.
  • Printed wiring boards (PWB) and printed circuit boards (PCB).
  • Parts list (bill of materials).