DOWNLOAD Sharp AR-LC9 Service Manual ↓ Size: 3.83 MB | Pages: 44 in PDF or view online for FREE

AR-LC9  UNPACKING AND INSTALLATION  3 - 2

1) Fit the upper mounting plates with the securing screws A (two

for each).

2) Fit the mounting plate to the lower part of the stand with the

two securing screws A.

3) Remove the two pawls on the LCC cover, and detach the LCC

cover.

1) Remove the two bottom plate securing stepped screws

attached to the large capacity tray.

2) Insert the connecting plate with the marking surface up into

the lower part of the large capacity tray from the marking side.

3) Attach the connecting plate by inserting screw C into the hole

of marking "A" of the connecting plate.

1) Insert the connecting plate attached to the large capacity tray

to the mounting plate at the lower part of the optional stand
until the base is inserted.

At this time, lift the leading end of the connecting plate a little
to insert the plate easily.

2) Gently detach the large capacity tray from the main unit and

check that the tray is locked.

3) With the tray locked, attach the securing plate with two screws

C.

1) Move the large capacity tray near the main unit.

2) Adjust the height using the following procedure so that the rib

of the large capacity tray is aligned with the axis of mounting
plate A attached to the main unit viewing from the top.

Push the large capacity tray into the main unit.

<1> Loosen the two screws of the adjusting caster mounting plate

attached to the lower part of the large capacity tray.

<2> Turn the knob clockwise viewing from the top so that the rib is

aligned with the axis.

<3> After adjustment is complete, tighten the two screws of the

adjusting caster mounting plate and push the large capacity
tray into the main unit.

Make mounting holes with a driver, etc.

Rubber is attached
to the lower side.

Securing

screws A

Securing

screws A

LCC cover

Screw C

Connecting plate

Step
screws

Mounting plate

Connecting plate

Securing
plate
screw C

Securing
plate

Axis

Rib

AR-LC9  UNPACKING AND INSTALLATION  3 - 3

<1> Loosen the two screws of the adjusting caster mounting plate

attached to the lower part of the large capacity tray.

<2> Turn the knob counterclockwise viewing from the top so that

the rib is aligned with the axis.

<3> After adjustment is complete, tighten the two screws of the

adjusting caster mounting plate and push the large capacity
tray into the main unit.

1) Remove the fixing material from the large capacity paper feed

tray.

2) Remove the fixing material from the packaged part, and

remove the packaged part.

1) Slowly pull out the paper feed base tray until it stops.

2) Remove the paper feed base fixing screw (1 pc.) of the large

capacity tray.

3) Push the large capacity tray slowly into the original position.

Rib

Axis

Screws

Knob

Rib

Axis

Screws

Knob

AR-LC9  UNPACKING AND INSTALLATION  3 - 4

The factory setting of the paper size is A4. To select another size,
perform the following procedures.

1) Pull out the large capacity tray until it stops.

2) Then pull out the paper feed tray again until it stops.

1) Remove the four fixing screws (blue) which are fixing the

upper and the lower sections of the side plate F and the side
plate R.

2) Then fit the paper feed tray on the lower side of the side plate

F and the side plate R with the engraved marks of the side
plates according to the size, and insert it. Also fit the upper
side to the size and fix it with the four fixing screws (blue).

1) When changing the size of the side plate R, check to confirm

the mark positions of "

" on the side plate R and the size

guide adjustment plate.

2) Loosen the auxiliary guide fixing screw (Flat screw 1pc).

3) Change the mark position (

▲

) of the auxiliary guide and the

cassette R from A4 to LT, and fix them with the fixing screw
(flat screw, 1pc).

At that time, adjust so that the mark positions (

▲

) on the auxil-

iary guide and the cassette R are at the same positions of the
mark positions (

) of the side plate R and the size guide

adjustment plate checked in the procedure 1). (If the scale of
the size guide adjustment plate is at the center, set the posi-
tion at the center. If is it at 1mm toward the front side, set the
position at 1mm toward the front side.)

F side

R side

F side

R side

A4

LT

AR-LC9  UNPACKING AND INSTALLATION  3 - 5

1) Remove the rear edge shaft fixing screw (blue) on the right

side of the paper feed tray, and remove the rear edge shaft.

2) Tighten the removed rear edge shaft with the fixing screw

(blue screw) and store it in the storage space inside the front
cabinet.

3) Push the large capacity tray slowly into the original position.

1) Remove the four fixing screws (blue) which are fixing the

upper and the lower sections of the side plate F and the side
plate R.

2) Then fit the paper feed tray on the lower side of the side plate

F and the side plate R with the engraved marks of the side
plates according to the size, and insert it. Also fit the upper
side to the size and fix it with the four fixing screws (blue).

∗

Since the auxiliary guide is unnecessary, fix it to A4 or LT. (For
protection against missing of the part)

1) Remove the rear edge shaft fixing screw (blue) on the right

side of the paper feed tray, and remove the rear edge shaft.

2) Change the direction of the removed rear edge shaft as shown

in the figure below, insert it into the installing hole in the lower
paper feed base. Fit the upper section with a fixing screw (blue
screw).

F side

R side

F

R