Sharp AR-FX11 Service Manual ▷ View online
AR-FX11 SIMULATIONS, FAX SOFTWARE SWITCH 6-54
U.S.A.: U.S.A.
CA: Canada
U.K: U.Kingdom
GR: German
FR: France
134
1
Summer time
Used to set whether the summer time is automatically set
or not.
or not.
0
0
1
1
1
Follow the
destination.
destination.
YES
2
Receive rejection
record
record
Used to set whether the rejected record is remained on
the communication report or not when receive is rejected
by the receive rejection function.
the communication report or not when receive is rejected
by the receive rejection function.
0
0
0
0
0
Recorded
3,4 Time until resetting
when G3 DIS
cannot be received
in V.8 phase.
cannot be received
in V.8 phase.
When send is made via a satellite, if the DIS signal is not
acknowledged, the receive level is adjusted again and
receive is tried again. This setting is used to set the time
until resetting.
acknowledged, the receive level is adjusted again and
receive is tried again. This setting is used to set the time
until resetting.
0
0
0
0
0
10s
1
1
1
1
1
5
Report table output
when in receive
rejection
when in receive
rejection
Used to set whether the communication report is
outputted or not when receive is rejected with the receive
rejection function. ”Output” is enabled only when SW134-
2 is set to “0”.
outputted or not when receive is rejected with the receive
rejection function. ”Output” is enabled only when SW134-
2 is set to “0”.
0
0
0
0
0
Not output
6
Sheet count
method in case of
an error
method in case of
an error
Used to set whether an error page is included in the send
quantity count in FAX send or not. The default is: an error
page is not counted.
quantity count in FAX send or not. The default is: an error
page is not counted.
0
0
0
0
0
Send error
pages are
not included.
pages are
not included.
7
Not used
0
0
0
0
0
8
YES/NO of quick
memory send
setting
memory send
setting
Used to set whether the quick memory send ON/OFF is
displayed on the menu or not.
displayed on the menu or not.
1
1
1
1
1
Setting is
displayed.
displayed.
135 1-4 Scanner resource
securing time out in
direct send
direct send
Used to set the time out of the scanner warm-up time in
direct send.
Binary input
20 - 50 sec
direct send.
Binary input
20 - 50 sec
0
0
0
0
0
26sec
0
0
0
0
0
1
1
1
1
1
1
1
1
1
1
5
Energy-saving
reset with an
external TEL
reset with an
external TEL
Used to set whether the machine is reset from the
energy-saving mode or not when the hand set of the
external telephone is lifted in the energy-saving mode.
The default is: Not reset in Japan only.
energy-saving mode or not when the hand set of the
external telephone is lifted in the energy-saving mode.
The default is: Not reset in Japan only.
1
1
1
1
1
Reset
(Complete
reset)
(Complete
reset)
6
Not used
0
0
0
0
0
7
External auditor
check
check
Used to set whether Enable/Disable of the FAX
department management when an external auditor is
used. The default is Disable.
department management when an external auditor is
used. The default is Disable.
0
0
0
0
0
Check
8
Not used
0
0
0
0
0
136
1
RTC error
adjustment
adjustment
Used to correct advancement of the clock. The default is
No Correction.
No Correction.
0
0
0
0
0
No error
adjustment
adjustment
SW
No.
Bit
No.
Item
Switch serection and function
U.S.A.
CA
U.K
GR
FR
Initial value
Key operator
1
Enable
0
Disable
1
Not recorded
0
Recorded
Bit No.
3
4
8s
0
0
10s
0
1
12s
1
0
14s
1
1
1
Output
0
Not output
1
Send error pages are
included.
included.
0
Send error pages are
not included.
not included.
1
Setting is displayed.
0
Setting is not
displayed.
displayed.
1
Reset (Complete
reset)
reset)
0
Not reset (Only 24V
is reset.)
is reset.)
1
Not check
0
Check
1
Error adjustment
0
No error adjustment
[06]SIMULATIONS ・ FAXSOFTWARESWITCH.fm 54 ページ 2004年11月12日 金曜日 午後2時24分
AR-FX11 SIMULATIONS, FAX SOFTWARE SWITCH 6-55
U.S.A.: U.S.A.
CA: Canada
U.K: U.Kingdom
GR: German
FR: France
136 2-8 Not used
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
137 to 150 Not used
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
SW
No.
Bit
No.
Item
Switch serection and function
U.S.A.
CA
U.K
GR
FR
Initial value
Key operator
[06]SIMULATIONS ・ FAXSOFTWARESWITCH.fm 55 ページ 2004年11月12日 金曜日 午後2時24分
AR-FX11 KEY OPERATOR PROGRAM 7-1
[7] KEY OPERATOR PROGRAM
KEY OPERATOR PROGRAM
Set value(Default)
Remark
LIST PRINT/SET
LIST PRINT
KEY OPE. LIST
JUNK FAX # LIST
ACC. USAGE LIST
JUNK FAX # LIST
ACC. USAGE LIST
LIST SETTING
(PRINT SELECTION)
(PRINT SELECTION)
TRANSMISSION
ALWAYS PRINTS/
ERROR ONLY*/
NEVER PRINTS
ERROR ONLY*/
NEVER PRINTS
BROADCAST
ALWAYS PRINTS*/
ERROR ONLY/
NEVER PRINTS
ERROR ONLY/
NEVER PRINTS
ORIGINAL IMAGE PRINT SETTING ALWAYS PRINTS/
ERROR ONLY*/
NEVER PRINTS
NEVER PRINTS
RECEPTION
ALWAYS PRINTS/
ERROR ONLY/
NEVER PRINTS*
ERROR ONLY/
NEVER PRINTS*
CONF. RECEPTION
ALWAYS PRINTS*/
NEVER PRINTS
NEVER PRINTS
LIST SETTING
(AUTO LISTING)
(AUTO LISTING)
AUTO PRINT REPT AT LIMIT (50)
Print/Not print*
PRINT DAILY AT DESIGNATED
TIME
TIME
NOT SETTING
INITIAL SETTING
DIAL MODE
Tone*/20PPS/10 PPS
PAUSE TIME
1,2* - 15sec
OWN PASSCODE SET
SPEAKER VOLUME
On-hook volume
High/Middle*/Low
Ringer volume
Line monitor volume
TX/RX end volume
Scan end volume
Tone volume
Line monitor volume
TX/RX end volume
Scan end volume
Tone volume
High/Middle*/Low/OFF
TX/RX END SOUND
SEND
PATTERN 1/2*/3
RECEIVE
PATTERN 1/2*/3
END SOUND LENGTH
2.0/2.5/3.0*/3.5/4.0sec
EXTENSION TEL
ON*/OFF
DISTINCTIVE RING
OFF*/STANDARD(For SCA/SCNZ/SRH)
OFF*/STANDARD, PATTERN1/2/3/4/5(For
SEC/SECL)
OFF*/STANDARD, PATTERN1/2/3/4/5(For
SEC/SECL)
PBX SETTING MODE
ON/OFF*
For SEEG/
SEF only
SEF only
REMOTE RECEPTION*1
0 - 5* - 9
ACCOUNT CONTROL
Enabled/Disabled*
ACCOUNT # SET
Program, Delete, Change
DATE & TIME SET
DAYLIGHT SAVING
TIME SETTING
TIME SETTING
ON*/OFF(For SUK/SEEG/SEF/SCA/SCNZ)
ON/OFF*(For SEC/SECL)
ON/OFF*(For SEC/SECL)
DISABLE FAX PRINT HOLD
ON*/OFF
[07]KEY OPERATOR.fm 1 ページ 2004年11月16日 火曜日 午後5時55分
AR-FX11 KEY OPERATOR PROGRAM 7-2
*1)Only when an extension phone is connected.
*2)If you do not wish to have recalling take place, set the number of attempts to “0”.
*3)Only on models with the two-sided printing function.
SENDING
FUNCTION
FUNCTION
RES. CON. SET
Resolution
STANDARD*/FINE/SUPER FINE/
ULTRA FINE/FINE (HALF TONE) /
S-FINE (HALF TONE) /
U-FINE ( HALF TONE)
ULTRA FINE/FINE (HALF TONE) /
S-FINE (HALF TONE) /
U-FINE ( HALF TONE)
Exposure
Auto*
AUTO REDUCE TX
Enabled*/Disabled
ROTATE TX
Enabled*/Disabled
PAGE COUNTER SET
Enabled*/Disabled
SEND MODE
MEMORY TX*/DIRECT TX
QUICK ON LINE TX
Enabled*/Disabled
PRINT STATION # IN RCVD
DATA
DATA
Out*/IN DATA
ACC. NAME PRINT
Enabled/Disabled*
RECALL SETTING (BUSY)*2
2 recall attempts at intervals of 3 minutes.
RECALL SET (ERR)*2
1 recall attempt at intervals of 1 minute.
For SEC/
SECL only
SECL only
RING TIMEOUT IN AUTO TX
30/45*/60sec
30/45*(For SRH/SOCC)
30/45*(For SRH/SOCC)
AUTO COVER SHEET
Enabled/Disabled*
RCV. FUNCTION
FAX RECEPTION LIGHT
PATTERN1*/2/OFF
#OF RINGS AT. RX
0 - 2* - 9
0 - 2* - 15(For /SRS/SRCC/SBI)
0 - 2* - 15(For /SRS/SRCC/SBI)
#OF RINGS MAN. RX
0*-9
For SEF
only
only
TRAY SELECTION
TRAY1,TRAY2, TRAY3
Enabled*/Disabled
RECEIVED DATA PRINT
CONDITION
CONDITION
REDUCTION*/DIVISION
AUTO RCV REDUCE TO
REGULAR SIZE
REGULAR SIZE
Enabled*/Disabled
DUPLEX RECEPTION*3
ON/OFF*
A3 RX REDUCE
ON/OFF*
FW. RX DATA
Enabled/Disabled*
RECEIVED DATA FW.
STATION SET
STATION SET
INDEX PRINT
Enabled/Disabled*
EARLIER OUTPUT
Enabled*/Disabled
ANTI JUNK FAX
Enabled/Disabled*
ENTER JUNK FAX #
POLLING
SECURITY
SECURITY
POLLING SECURITY
Enabled*/Disabled
POLLING PASSCODE #
MODE
MODE
KEY OPERATOR PROGRAM
Set value(Default)
Remark
[07]KEY OPERATOR.fm 2 ページ 2004年11月16日 火曜日 午後5時55分
Click on the first or last page to see other AR-FX11 service manuals if exist.