DOWNLOAD Sharp AR-FN6 Service Manual ↓ Size: 4.63 MB | Pages: 25 in PDF or view online for FREE

Model
AR-FN6
Pages
25
Size
4.63 MB
Type
PDF
Document
Service Manual
Brand
Device
Copying Equipment / Service Manual
File
ar-fn6.pdf
Date

Sharp AR-FN6 Service Manual ▷ View online

AR-FN6 MACHINE OPERATION-1
[6] MACHINE OPERATION
1. Using the stapling function from the printer feature
When using the stapling function, select "Properties" on the printer driver setting screen, open the "Main" tab shown in the right illustration, and then
select "Left", "Right" or "Top " at "Binding Edge" and "1 Staple" or  "2 Staples" in the "Staple" drop down.
NOTES:
•The settings screens above will appear only if the devices have been set properly in the printer driver.
•The combination of paper selection and other functions may not be compatible. For instance, if heavy paper, envelopes, label stock, etc. are selected,
it will not be possible to select duplex, offset tray, saddle stitch, etc.
The illustration below shows the screen for a PCL printer driver in the Windows 98 environment.
2. Using the finisher functions in the copy mode
If you touch the [OUTPUT] key on the copy mode basic screen, a screen for selecting the sort/group/staple sort functions and selecting an exit tray will
appear.
1 : [GROUP] key
If this function is selected, all copies of the same original will be grouped.
2 : [STAPLE SORT] key
If this function is selected, sorted copies will be stapled and delivered to
the offset tray. (not offset stacked)
3 : [SORT] key
If this function is selected, each set of copies will be sequentially
delivered.
4 : Icon display
The icon of the selected function (sort, staple sort or group) is displayed.
5 : [OFFSET] key
If this function is selected (checked), the offset function will be enabled. If
the check mark is cleared, the offset function will be disabled. (If the
staple sort function is selected, the check mark of the offset function will
be automatically cleared.)
6 : [OFFSET TRAY] key
If the offset tray is selected, printed sheets will be delivered to the offset
tray. (If the staple sort function is selected, the offset tray will be
automatically selected.)
7 : [TOP TRAY] key
If the top tray is selected, printed sheets will be delivered to the top tray.
8 : [OK] key
Press to close this screen and to return to the basic screen.
*
If a function is selected, the corresponding key will be highlighted.
OK
STAPLE 
SORT
OUTPUT
GROUP
SORT
OFFSET 
TRAY
TOP TRAY
OFFSET
1
2
3
4
5
6
7
8
AR-FN6 MACHINE OPERATION-2
3. Stapling position quick reference list
When stapling is performed, the orientation of image data or original is related to the stapling position, binding position and orientation of paper
complicatedly. The table below shows the relation.
NOTES:
•When using the stapling function, select the offset tray as an exit tray. If another tray is selected, the stapling function cannot be used.
•Select only one paper size. If different sizes are included, stapling cannot be performed.
*
The following types of paper cannot be stapled.
Pre-punched paper, transparency film, heavy paper, label, envelope, postcard
Image data or original
Result
First page (front side)
Second page (reverse side)
Two sides
Portrait orientation printing
Left binding
T
op binding
Right binding
Left binding
T
op binding
Right binding
One-position stapling Two-position stapling
One-position stapling Two-position stapling
One-position stapling
Landscape or
ientation pr
inting
Two-position stapling
One-position stapling
One-position stapling
One-position stapling
Two-position 
stapling with left 
binding cannot be 
made.
Two-position 
stapling with right 
binding cannot be 
made.
Two-position 
stapling with top 
binding cannot be 
made.
indicates stapling positions.
AR-FN6 ADJUSTMENTS-1
[7] ADJUSTMENTS
1. Jogger position adjustment
A. Jogger F/R
1) Staple 5 sheets of A4 or LT paper and check the paper shift (A)
shown in the figure below.
2) If the shift (A) is less than 1mm, there is no need to adjust.
3) If the shift (A) is 1mm or greater, adjust as shown in the table below.
B. Printer model adjustment procedure
1) In the DIAG MODE, select [FINISHER JOGGER ADJ.].
2) Press [OK] key, and the following display will be shown.
Use [
] key and [
] key to change the adjustments value.
(Adjustment range: 40 - 60)
3) Change the adjustment value and press OK key, and the stopper will
be turned on and the finisher joggers F/R will move to and stop at the
positions shown in the table below. 
4) When the joggers F/R stop, open the door and load A$/LT paper in
the alignment tray, and check the jogger width visually. 
5) When the jogger width is too wide or too narrow, use [
] key and
[
] key again to change the adjustments value. Press [OK] key to
shift the jogger to the A4/LT alignment position, and check visually. 
The table below shows relationship between the adjustment value and
the jogger width.
6) After completion of the adjustment, remove the paper from the
alignment tray and terminate the DIAG MODE.
C. MFP adjustment procedure
1) When the sub code of the simulation is entered, the following display
is shown.
SIM 3-6: Jogger position adjustment
2) Enter the adjustment value with [0] - [9] keys and press START key,
and the menu below will be displayed. (Adjustment range: 40 - 60)
SIM 3-6: Jogger moving
When the stopper is turned on, and finisher joggers F/R move to and
stop at the positions shown in the table below.
3) When the joggers F/R stop, open the door and load A4/LT paper in
the alignment tray, and check the jogger width visually. 
4) When the jogger width is too wide or too narrow, use [0] - [9] key
again to change the adjustments value. Press [START] key to shift
the jogger to the A4/LT alignment position, and check visually. 
The table below shows relationship between the adjustment value and
the jogger width.
5) After completion of the adjustment, remove the paper from the
alignment tray and terminate the simulation.
Model
Adjustment procedure
Pinter model
DIAG MODE
[FINISHER JOGGER ADJ.]
(Finisher jogger position adjustment)
MFP
SIM 3-6(Built-in finisher jogger position adjustment)
Destination
Jogger position
Inch series
LT size alignment position
AB series
A4 size alignment position
(A)
Staple
Jogger F
Jogger R
FINISHER JOGGER ADJ.
ADJUST VALUE
50
Adjustment value
Jogger width
Decreased by 1.
Increased by about 0.375mm.
Increased by 1.
Decreased by about 0.375mm
Destination
Jogger position
Inch series
LT size alignment position
AB series
A4 size alignment position
Adjustment value
Jogger width
Decreased by 1.
Increased by about 0.375mm.
Increased by 1.
Decreased by about 0.375mm
SIMULATION 3-6
FINISHER JOGGER ADJUSTMENT.INPUT VALUE 40-60,AND PRESS START.
50
SIMULATION 3-6
FINISHER JOGGER ADJUSTMENT.MOVING...
50
AR-FN6 DISASSEMBLY AND ASSEMBLY, MAINTENANCE-1
[8] DISASSEMBLY AND ASSEMBLY, MAINTENANCE
1. Maintenance System Table
A. When installed to a AR-series machine
B. When installed to a DM-series machine
Check (Clean, replace, or adjust as necessary.)
Clean
Replace
Adjust
Lubricate
Move position
Unit name
Part name
When 
calling
50K
100K 150K 200K 250K 300K 350K 400K
Remark
Transport section
Transport rollers
De-curler roller
(
)
Transport paper 
guides
Drive section
Gears
(Specified position)
Belts
Other
Sensors
Discharge brush
Staple un
Replace UN at 100K staple.
Staple cartridge
User replacement for every 3000pcs.
Unit name
Part name
When 
calling
50K
100K 150K 200K 250K 300K 350K 400K
Remark
Transport section
Transport rollers
De-curler roller
(
)
Transport paper 
guides
Drive section
Gears
(Specified position)
Belts
Other
Sensors
Discharge brush
Staple un
Replace UN at 100K staple.
Staple cartridge
User replacement for every 3000pcs.
Page of 25
Display

Click on the first or last page to see other AR-FN6 service manuals if exist.