Sharp AR-FN6 Service Manual ▷ View online
AR-FN6 SPECIFICATIONS-1
[3] SPECIFICATIONS
1. Basic
2. Staple parts
3. Consumable parts
Type
Desktop type finisher with dual exit tray
Transport speed
To support 35-45 sheet/minute
Transport alignment
Center alignment
Tray type
(No. of tray)
(No. of tray)
Upper
tray
tray
EXIT tray
Lower
Tray
Tray
Ascent/descent type offset tray
Output paper
capacity
capacity
Upper
tray
tray
500 sheets sheets (A4/8.5"x11", 80g/m²)
Lower
Tray
Tray
750 sheets (A4/8.5"x11", 80g/m²)
Output paper delivery
Face-down
Output paper
size
size
Upper
tray
tray
A3, B4, A4, A4R, B5, B5R, A5R
11"x17", 8.5"x14", 8.5"x13", 8.5"x11",
8.5"x11"R,5.5"x8.5"R,
Executive, Japanese post card,
Monarch(98x191),Com-10(105x241),
DL(110x220),C5(162x229),
ISO B5(176x250)
11"x17", 8.5"x14", 8.5"x13", 8.5"x11",
8.5"x11"R,5.5"x8.5"R,
Executive, Japanese post card,
Monarch(98x191),Com-10(105x241),
DL(110x220),C5(162x229),
ISO B5(176x250)
Lower
Tray
Tray
Spec of media
for paper
output
for paper
output
Upper
tray
tray
Tracing paper:52-59g/m² / 14-15lbs
Plain paper:60-128g/m² / 16-34lbs
Index paper:176g/m² / 47lbs
Cover paper:205g/m² / 54-55lbs
Transparency
Plain paper:60-128g/m² / 16-34lbs
Index paper:176g/m² / 47lbs
Cover paper:205g/m² / 54-55lbs
Transparency
Lower
Tray
Tray
Plain 60-128g/m² /16-34lbs
Remaining
paper
detection
paper
detection
Upper
tray
tray
Not provided
Lower
Tray
Tray
Provided
Exit tray full
detection
detection
Upper
tray
tray
Provided
Lower
tray
tray
Provided
Power consumption
Less than about 67.3W
Power source
Supplied from the optional power source
(DC24V 2.7A / DC5V 0.5A)
(DC24V 2.7A / DC5V 0.5A)
External
dimensions(WxDxH)
dimensions(WxDxH)
Occupied
dimensions(WxD)
dimensions(WxD)
Weight
Approx. 23kg
Offset stack
Offset volume:25mm
Paper size to be
stapled
stapled
A4, B5, 8.5"x11"
Ability of stapler
(Max. # of pages
for staple)
(Max. # of pages
for staple)
30 sheets (smaller than A4/8.5"x11", 80g/m²)
Stapling pattern
3 patterns (front 1/rear 1/both)
Stacking
performance
performance
Offset
Horizontal displacement:
Less than 15mm
(Less than 10mm up to
250 sheets)
Vertical displacement:
Less than 15mm
(In the non-staple mode on
the offset tray)
Less than 15mm
(Less than 10mm up to
250 sheets)
Vertical displacement:
Less than 15mm
(In the non-staple mode on
the offset tray)
Matching
Max. deviation width
Within 2mm
(In the staple mode on the
offset tray)
offset tray)
Staple supply
Refill system
Staple detection Staple empty
Provided
No cartridge
Provided
Staple jam
Provided
Kinds of paper
which cannot be
stapled
which cannot be
stapled
Pre-punched paper, transparency film, heavy paper,
label, envelope, postcard
label, envelope, postcard
Name
Content
Life
Product
name
Remark
Staple
cartridge
cartridge
Staple
cartridge
cartridge
x3
5000x3 AR-SC1
Common with cartridge
for AR-FN4 & AR-FN6
for AR-FN4 & AR-FN6
AR-FN6 UNPACKING AND INSTALLATION-1
[4] UNPACKING AND INSTALLATION
<Before installation>
• For installation of AR-FN6, an optional stand/paper drawer (stand/MPD
& 2000 sheet paper drawer, stand/3 x 500 sheet paper drawer or multi
purpose drawer) must have been installed.
purpose drawer) must have been installed.
Also if a multi purpose drawer has been installed, a power supply unit
(AR-DC1) is needed additionally.
1) Turn off the main switch of the main unit of the printer.
Turn the main switch located on the front side of the main unit to the
"OFF" position.
Then, remove the power plug of the main unit from the outlet.
2) Remove the upper cabinet of the stand/paper drawer.
<1>Pull out the paper tray of the stand/paper drawer.
<1>Pull out the paper tray of the stand/paper drawer.
Remove the four screws of the cabinet attached to the right side of
the main unit of the printer and remove the cabinet.
<2>Mount screw B to the position shown in the illustration.
3) Attach the finisher.
<1>Remove the paper exit actuator from the main unit of the printer.
<1>Remove the paper exit actuator from the main unit of the printer.
<2>Raise the relay unit at the side of the finisher.
<3>Put the finisher on the stand/paper drawer.
Put the finisher on the stand/paper drawer temporarily and push the
lower part to slide to the exit tray section of the main unit and to
attach the finisher.
<4>Open the front cover of the finisher and fix the finisher with three
screws A at the positions shown in the illustration.
Then, close the front cover and close the paper tray of the stand/
paper drawer.
paper drawer.
<Parts included>
Mounting plates: 2 pcs.
Staple cartridge: 1 pc.
Tray 1: 1 pc.
Paper holder: 1 pc.
Screws A: 5 pcs.
Screw B: 1 pc.
Tray 2: 1 pc.
"OFF"
Cabinet
Screw B
Actuator
Relay unit
1
2
Screws A
Screws A
(Front side)
AR-FN6 UNPACKING AND INSTALLATION-2
<5>Attach the mounting plates to the positions shown in the illustration
and fix them with screws A.
4) Insert the staple cartridge.
<1>Pull out the staple unit.
<2>Insert the staple cartridge.
<3>Slide the release lever to the left and return the staple unit.
5) Attach the trays and the paper holder.
Attach tray 1, tray 2, and the paper holder to the positions shown in
the illustration.
6) Remove the AC inlet cover and then remove the rear cabinet of the
stand/paper drawer.
<1>Remove the screw that fixes the AC inlet cover and then remove the
AC inlet cover.
<2>Remove the AC cord of the power supply unit from the inlet
connector of the main unit of the printer.
Remove the four screws that fix the rear cabinet and then remove the
rear cabinet.
rear cabinet.
If a multi purpose drawer has been installed, steps 7) to 9) are needed.
If a stand/MPD & 2000 sheet paper drawer or stand/3 x 500 sheet paper
drawer has been installed, proceed to step 10).
drawer has been installed, proceed to step 10).
7) Process the AC inlet cover attached to the rear cabinet of the stand/
paper drawer.
Remove the screw that fixes the AC inlet cover and then remove the
AC inlet cover.
AC inlet cover.
Process the AC inlet cover as shown in the illustration.
Mounting plates
Screws A
(Rear side)
Tray 1
Paper holder
Tray 2
Screw
AC inlet cover
Rear cabinet
AC inlet cover
Cut out.
AR-FN6 UNPACKING AND INSTALLATION-3
8) Attach the power supply unit.
Attach the power supply unit to the positioning portion of the multi
purpose drawer and then fix it with three supplied screws.
9) Connect the power supply unit harness to the PCU PWB of the main
unit of the printer.
<1>Remove the screw that fixes the harness cover of the main unit of the
printer and slide the harness cover up to remove it.
Process the harness cover as shown in the illustration.
<2>Connect the power supply unit harness connector to CN11 (red
connector) of the PCU PWB of the main unit of the printer.
<3>Reattach the harness cover to its original position and fix it with the
removed screw.
At this time, ensure that the power supply unit harness is arranged
At this time, ensure that the power supply unit harness is arranged
as shown in the illustration.
•Fix the harness securely to the wire saddle.
10) Arrange the harness of the finisher.
<1>Pass the harness of the finisher between the power supply unit and
<1>Pass the harness of the finisher between the power supply unit and
the frame of the stand/paper drawer and connect it to the connector
of the power supply unit.
<2>Fit the snap band attached to the finisher at the position shown in the
illustration to fix the harness.
11) Attach the rear cabinet of the stand/paper drawer.
<1>Pass the AC cord of the power supply unit as shown in the illustration
and fix the rear cabinet of the stand/paper drawer with the screws.
<2>Attach the AC inlet cover to the rear cabinet of the stand/paper
drawer and fix it with the removed screw.
12) Connect the AC cord of the optional power supply unit to the main
unit of the printer.
<1>Connect the AC cord of the power supply unit to the inlet connector
of the main unit of the printer at the location shown in the illustration.
Optional power supply unit
Screws
Screws
Harness cover
Cut out.
Screw
Connector
CN11
Wire saddle
Harness cover
Optional power
supply harnesses
supply harnesses
Screw
Wire saddle
Snap band
Finisher harness
Power supply unit
connector
connector
Rear cabinet
Screw
AC inlet cover
AC cord