DOWNLOAD Sharp AR-FN5 (serv.man2) Service Manual ↓ Size: 1.48 MB | Pages: 15 in PDF or view online for FREE

Model
AR-FN5 (serv.man2)
Pages
15
Size
1.48 MB
Type
PDF
Document
Service Manual
Brand
Device
Copying Equipment / Operational descriptions Disassembly and assembly Adjustments
File
ar-fn5-sm2.pdf
Date

Sharp AR-FN5 (serv.man2) Service Manual ▷ View online

4. Paper exit unit motor
A. Main drive motor
4-A-1
4-A-2
B. Offset tray drive motor
Refer to Fig.(3-1) to (3-4).
4-B-1
C. Lift-up motor
Note: Perform this procedure after removing the right cabinet (Step
3-5).
Refer to Fig.(3-1) to (3-6).
4-C-1
4-C-2
5. Paper exit unit solenoid
Refer to Fig.(3-1) to (3-6).
5-1
1)
2)
4)
3)
1)
2)
3)
1)
2)
3)
1)
2)
3)
1)
1)
2)
3)
1)
2)
3)
5-2
5-3
6. Alignment unit roller
6-1
6-2
6-3
6-4
3)
1)
2)
2)
1)
2)
1)
1)
2)
3)
4)
1)
1)
2)
2)
3)
4)
5)
4)
6)
7. Alignment unit motor
Refer to Fig.(6-1) to (6-2).
7-1
7-2
7-3
7-4
8. Alignment unit solenoid
Refer to Fig.(7-1) to (7-2).
A. Upper alignment plate drive solenoid
8-1
B. Transport switch gate solenoid right
8-2
1)
2)
1)
2)
1)
1)
2)
1)
1)
1)
2)
3)
3)
5)
5)
3)
4)
4)
1)
2)
2)
1)
2)
C. Rear edge plate solenoid
Refer to Fig.(7-3).
8-3
8-4
D. Shutter drive solenoid
Refer to Fig.(7-3).
8-5
E. Transport switch gate solenoid
Refer to Fig.(1-A-1) to (1-A-5).
Refer to Fig.(6-1) to (6-2).
8-7
[6] ADJUSTMENTS
Adjustments are required when replacing the following parts:
A. Rear edge plate unit
B. Side guide plate
C. Gate solenoid right
D. Gate solenoid left
E. Upper alignment solenoid
F. Shutter solenoid
G. Rear edge plate solenoid
H. Paper holding solenoid
A. Rear edge plate unit
1. Staple 5 sheets of A4 or LT paper, and check the slide shift of the
paper bundle in the transport direction (Y-axis).
2. When the shift of the paper bundle is within 1mm, there is no need
to adjust.
3. If the shift of the paper bundle is greater than 1mm, execute SIM
3-6-3 to adjust the rear edge plate position.
B. Side guide plate
1. Staple 5 sheets of A4 or LT paper, and check the slide shift of the
paper bundle in the vertical direction (X-axis) to the transport direc-
tion.
2. When the shift of the paper bundle is within 1mm, there is no need
to adjust.
3. If the shift of the paper bundle is greater than 1mm, execute SIM
3-6-2 to adjust the side guide plate position. Also check that the
paper bundle is in parallel with the alignment reference wall of the
side guide plate.
SIM 3-6 Finisher alignment member adjustment
When a sub code is entered, the above display is shown.
1. In SIM 3-6-1, press [OK] and select [1] - [10] to specify the paper
size.
2. Enter SIM 3-6-2 Jogger pos X (side guide plate) or SIM 3-6-3
Jogger pos Y (rear edge plate) and press [OK]. The alignment
section (rear edge plate unit), side guide plate) will be operated.
During the load operation, the [OK] key is highlighted.
3. Keep the alignment member at the paper alignment position, and
open the alignment section. Insert paper of the same size into the
alignment member and check that the tightness is proper. 1~2 mm
smaller (tight) than the paper size is O.K.
4. When the adjustment value of the simulation is decreased by 1,
the clearance between paper and the side guide plate is de-
creased by 0.41mm, and between paper and the rear edge plate
0.83mm, and vice versa.
1)
2)
4)
3)
5)
1)
2)
1)
2)
3)
4)
1)
2)
Sim3-6 JOGGER ADJ.
1:PAPER SIZE
2:JOGGER POS X
3:JOGGER POS Y
1
(Initial screen)
Page of 15
Display

Click on the first or last page to see other AR-FN5 (serv.man2) service manuals if exist.