Sharp AR-FN3 (serv.man2) Service Manual ▷ View online
[6] ADJUSTMENTS
The following table shows the main parts requiring adjustment at the
time of replacement
time of replacement
Item
Part name
1
Jogger F/R
2
Paper discharge gate solenoid 1
3
Paper discharge gate solenoid 2
4
Paper discharge gate solenoid 3
5
Paper holding solenoid
6
Paddler clutch
7
Vertical transport de-curler
Note: Remove or install parts in numerical order shown in the follow-
ing figures.
1. Jogger F/R
A. Let the unit staple 5 sheets of A4 or letter paper and check the
bundle of the sheets for deviation in directions A).
B. If the deviation in directions A) are within 1 mm, there is no need
to adjust the jogger F/R.
C. When the deviation exceeds 1 mm, adjust the jogger F/R accord-
ing to the simulation 3-6: Adjusting Finisher Jogger Position.
Sim. 3-6: Adjusting Finisher Jogger Position
The screen above is displayed after the sub number of the simulation
is entered.
is entered.
1) Adjust the value with the numeric keypad.
2) The joggers in the finisher are operated by pressing the [EX-
ECUTE] key. The [EXECUTE] key is displayed in reverse video
during loading operation. When the [EXECUTE] key in this state
is pressed, loading operation can be canceled.
during loading operation. When the [EXECUTE] key in this state
is pressed, loading operation can be canceled.
Condition
Adjusting procedure
1
When the
deviation in the
direction A)
exceeds 1 mm.
deviation in the
direction A)
exceeds 1 mm.
Decrease the simulation value.
(Decreasing the simulation by 1 narrows
the width between the joggers by 0.63
mm.)
(Decreasing the simulation by 1 narrows
the width between the joggers by 0.63
mm.)
Increase the simulation value. (Increasing
the simulation value by 1 widens the width
between the joggers by 0.63 mm)
the simulation value by 1 widens the width
between the joggers by 0.63 mm)
Note: The width between joggers can be visually checked by observ-
ing the label inside the staple tray.
2. Paper discharge gate solenoid 1
A)
Pin
A
Jogger
Label
Letter position
Jogger
A4 position
The spacing between
labels is 0.5 mm.
labels is 0.5 mm.
2)
1)
3)
2)
2)
1)
2)
AR-FN3
6 – 1
8/19/1999
[Adjustment and precaution in setting]
Manually pull the plunger to move it in the arrow direction until it
stops, and fix it at that position.
stops, and fix it at that position.
3. Paper discharge gate solenoid 2
[Adjustment and precaution in setting]
Fit the edge of plate to which the solenoid is attached, with the left
edge of the marking.
edge of the marking.
At that time, check that the rib of the paper discharge gate 2 and the
rib inside the left cabinet 1 are aligned on a line as shown in the figure
with the solenoid pulled completely.
rib inside the left cabinet 1 are aligned on a line as shown in the figure
with the solenoid pulled completely.
7)
4)
5)
6)
1)
2)
2)
3)
7)
4)
5)
6)
AR-FN3
8/19/1999
6 – 2
4. Paper discharge gate solenoid 3
[Adjustment and precaution in setting]
Paper discharge gate (OG3SL) adjustment procedures
Manually pull the plunger in the arrow direction until it stops, and fix it
at that position.
at that position.
5. Paper holding solenoid
[Adjustment and note for setting]
Fix it at the center of the long hole.
1)
2)
2)
3)
7)
4)
5)
6)
1)
2)
2)
3)
AR-FN3
6 – 3
8/19/1999
6. Paddler clutch
[Adjustment and note for setting]
Loosen the fixing screw (indicated with an arrow in the figure) of the
paddler adjustment plate, and turn the paddler adjustment plate in the
arrow direction and fix it.
paddler adjustment plate, and turn the paddler adjustment plate in the
arrow direction and fix it.
1)
2)
2)
3)
Paddler
Staple
movable
PG
movable
PG
AR-FN3
8/19/1999
6 – 4
Click on the first or last page to see other AR-FN3 (serv.man2) service manuals if exist.