Sharp AR-D17-19 (serv.man2) Service Manual ▷ View online
AR-D17/D18/D19 ADJUSTMENTS 5 - 2
6) Move the paper to the rear side of the alignment plate, and check
that the clearance between the alignment plate (F side) and the
paper is 0 – 0.5mm.
paper is 0 – 0.5mm.
• When the clearance between the alignment plate and the paper is in
0 – 0.5mm:
Remove the paper in the ADU unit. Press [CA] key to cancel the sim-
ulation mode.
ulation mode.
• When the clearance between the alignment plate and the paper is
out of 0 – 0.5mm:
1. Remain the paper in the ADU unit, and insert the ADU unit and
change the set value.
(Example) When 45 is set:
Reference for set value
The relationship between the set value and the alignment plate
width is as shown below:
width is as shown below:
∗
However, when performing an adjustment for a paper feed tray set
at A4R/A5/B5R, pull out the ADU unit and check the clearance
and be sure to remove the paper. (Every time when the set value
is changed, a sheet of paper is fed from the paper feed tray.)
at A4R/A5/B5R, pull out the ADU unit and check the clearance
and be sure to remove the paper. (Every time when the set value
is changed, a sheet of paper is fed from the paper feed tray.)
2. When [EXECUTE] on the LCD panel is pressed, alignment is
performed with the set value. During alignment operation, [EXE-
CUTE] is highlighted.
CUTE] is highlighted.
3. When alignment operation is completed, [EXECUTE] returns to
the normal display. Pull out the ADU unit again and check the
clearance between the alignment plate and the paper. (When
checking, be sure to move the paper to the rear end of the align-
ment plate.)
clearance between the alignment plate and the paper. (When
checking, be sure to move the paper to the rear end of the align-
ment plate.)
If the clearance is out of 0 – 0.5mm, repeat procedures 1 – 3 to
adjust. Enter the same set value for other paper feed trays.
adjust. Enter the same set value for other paper feed trays.
4. After completion of the adjustment, remove paper from the ADU
unit, and press [CA] key to cancel the simulating mode.
Set value
Alignment plate width
Decreased by 1
Widened by about 0.3mm
Increased by 1
Narrowed by about 0.3mm
0 0.5mm
Paper
Alignment
plate R
plate R
Alignment
plate F
plate F
4
5
AR-D17/D18/D19 DISASSEMBLY, ASSEMBLY, AND MAINTENANCE 6 - 1
[6] DISASSEMBLY, ASSEMBLY, AND MAINTENANCE
1. Maintenance system table
✕
: Check (Clean, replace, or adjust as necessary.)
❍
: Clean
▲
: Replace
∆
: Adjust
✩
: Lubricate
*1: Reference for replacement: Counter value at each paper feed port
Paper feed rollers: 100K or 2 years
Part name
Call
50K
100K
150K
200K
250K
300K
350K
400K
Remark
Paper feed
separation section
separation section
1
Paper feed rollers
(
❍
)
✕
❍
✕
❍
✕
❍
✕
❍
✕
*1
2
Earth spring
✕
✕
✕
✕
✕
3
Torque limiter
(
❍
)
✕
✕
✕
✕
✕
Transport section
4
Transport rollers
❍
❍
❍
❍
❍
❍
❍
❍
❍
5
Rollers
❍
❍
❍
❍
❍
❍
❍
❍
❍
6
Transport paper guides
❍
❍
❍
❍
❍
❍
❍
❍
❍
Drive section
7
Desk gears
✕
✕
✕
✕
✕
(Specified position)
8
ADU gears
✕
✕
✕
✕
✕
(Specified position)
9
Belts
✕
✕
Others
10
Sensors
✕
✕
✕
✕
✕
4
4
9
9
9
9
9
4
9
4
5
5
8
8
5
6
7
7
7
5
5
5
5
5
10
1
1
3
2
10
10
10
10
10
10
AR-D17/D18/D19 DISASSEMBLY, ASSEMBLY, AND MAINTENANCE 6 - 2
2. Disassembly and assembly
A. Paper feed separation section
(1) Paper feed rollers
1) Pull out the tray unit (A).
2) Remove the screw, and remove the tray stoppers left (B) and the
tray stopper right (C).
3) Lift the tray unit and remove it.
4) Remove the screw and remove the tray rail R (D).
5) Remove the screw and remove the paper feed unit (E).
AR-D17/D18
AR-D19
Part name
Call
50K
100K
150K
200K
250K
300K
350K
400K
Remark
Paper feed
separation section
separation section
Paper feed rollers
(
❍
)
✕
❍
✕
❍
✕
❍
✕
❍
✕
Earth spring
✕
✕
✕
✕
✕
Torque limiter
(
❍
)
✕
✕
✕
✕
✕
C
B
A
D
E
D
E
AR-D17/D18/D19 DISASSEMBLY, ASSEMBLY, AND MAINTENANCE 6 - 3
a. Paper pickup roller and paper feed roller removal
1) Remove the paper feed unit.
2) Disengage the pawl, and lift the pickup roller lever (A).
3) Remove the screw, and remove the paper feed wait plate (B).
4) Remove the stopper (C).
5) Disengage the pawl, and remove the pickup roller lever L (D).
6) Remove the pickup roller (E) and paper feed roller (F).
b. Separation roller removal
1) Remove the paper feed unit.
2) Remove the separation roller unit (A).
3) Remove the separation roller (B).
(2) Earth spring
1) Remove the paper feed unit.
(3) Torque limiter
1) Remove the paper feed unit.
A
B
C
D
E
F
A
B
Click on the first or last page to see other AR-D17-19 (serv.man2) service manuals if exist.