Sharp AR-D14 Service Manual ▷ View online
AR-D13/D14/MU1/DC1 UNPACKING AND INSTALLATION-6
<2>Pull out the paper tray of the multi purpose drawer until it stops and
attach the front mounting plates with two supplied screws.
Then, remove the lock of the paper tray and close the tray.
<3>Reattach the paper tray of the main unit of the printer.
4) Connect the harness to the main unit of the printer.
<1>Remove the screw that fixes the harness cover of the main unit of the
<1>Remove the screw that fixes the harness cover of the main unit of the
printer and then slide the harness cover up to remove it.
Process the harness cover as shown in the illustration.
<2>Connect the connector of the relay harness of the multi purpose
drawer to the connector of the PCU PWB of the main unit of the
printer.
If you do not install a finisher, saddle stitch finisher or mail-bin stacker,
the steps below are not needed. Proceed to step 10).
the steps below are not needed. Proceed to step 10).
5) Remove the rear cabinet of the multi purpose drawer.
<1>Remove the two screws that fix the rear cabinet of the multi purpose
<1>Remove the two screws that fix the rear cabinet of the multi purpose
drawer and then remove the rear cabinet.
<2>Remove the screw that fixes the AC inlet cover and then remove the
AC inlet cover.
Process the AC inlet cover as shown in the illustration.
6) Attach the power supply unit.
Attach the power supply unit to the positioning portion of the multi
purpose drawer and then fix it with three supplied screws.
purpose drawer and then fix it with three supplied screws.
7) Connect the power supply unit harness to the PCU PWB of the main
unit of the printer.
Connect the power supply harness connector to CN11 (red
connector) of the PCU PWB of the main unit of the printer.
Screw
Screw
Front mounting plate
Front
mounting plate
mounting plate
Harness cover
Cut out.
Screw
Connector
Rear cabinet
Screw
Screw
AC inlet cover
Cut out.
Optional power supply unit
Screws
Screws
CN11
Connector
AR-D13/D14/MU1/DC1 UNPACKING AND INSTALLATION-7
8) Attach the rear cabinet of the paper tray.
<1>Pass the AC cord of the power supply unit as shown in the illustration
<1>Pass the AC cord of the power supply unit as shown in the illustration
and attach the rear cabinet with two screws.
<2>Attach the AC inlet cover to the paper tray and fix it with the removed
screw.
9) Connect the AC cord of the power supply unit to the main unit of the
printer.
Connect the AC cord of the power supply unit to the inlet connector
of the main unit of the printer at the location shown in the illustration.
of the main unit of the printer at the location shown in the illustration.
Then, proceed to step 11).
10) Attach the harness cover.
Reattach the harness cover to its original position and fix it with the
removed screw.
At this time, ensure that the power supply unit harness is arranged
At this time, ensure that the power supply unit harness is arranged
as shown in the illustration.
•Fix the harness securely to the wire saddle.
11) Adjust the position of the paper guides of the paper tray.
Refer to "Setting and adjustment" described later.
4.AR-DC1
<Before installation>
•Start installation after checking that the DATA indicator on the operation
panel is not lit or blinking.
1) Turn the main switch of the printer to "OFF".
Turn the main switch located on the front of the printer to "OFF".
Then, remove the power plug of the printer from the outlet.
2) Remove the multi rear cabinet.
Remove the two screws that secure the multi rear cabinet and
remove the multi rear cabinet.
remove the multi rear cabinet.
3) Remove the AC inlet cover from the multi rear cabinet.
Remove the screw that secures the AC inlet cover and remove the
AC inlet cover.
Work the AC inlet cover as shown in the illustration.
Work the AC inlet cover as shown in the illustration.
Rear cabinet
Screw
Screw
AC cord
Screw
AC inlet cover
AC cord
Wire saddle
Harness cover
Screw
Optional power
supply harnesses
supply harnesses
Wire saddle
Parts included
Screws (3)
ACCESSORY
I.T.E.
9K11
9K11
"OFF"
Multi rear cabinet
Screw
Screw
AC inlet cover
Cut-out
AR-D13/D14/MU1/DC1 UNPACKING AND INSTALLATION-8
4) Attach an optional power supply unit to the multi-purpose section.
Attach an optional power supply unit to the positioning portion of the
multi-purpose section and secure it with the three screws included in
this product.
5) Connect the optional power supply harness to the PCU PWB of the
printer.
<1>Remove the screw that secures the harness cover of the printer and
slide the harness cover upward to remove it.
Work the harness cover as shown in the illustration.
<2>Connect the connector of the optional power supply harness to
CN11 of the PCU PWB of the printer.
<3>Reattach the harness cover to its original position and secure it with
the removed screw.
At this time, check that wiring of the optional power supply harness
has been handled as shown in the illustration.
6) Attach the multi rear cabinet.
<1>Pass the AC cord of the optional power supply unit as shown in the
<1>Pass the AC cord of the optional power supply unit as shown in the
illustration and secure the multi rear cabinet with the two screws.
<2>Attach the AC inlet cover to the multi rear cabinet and secure it with
the removed screw.
7) Connect the AC cord of the optional power supply unit to the printer.
Connect the AC cord of the optional power supply unit to the position
of the inlet connector of the printer shown in the illustration.
8) Turn the power switch of the printer to "ON".
Insert the power plug of the printer to the outlet.
Then, turn the main switch located on the front of the printer to "ON".
Optional power supply unit
Screw
Screws
Harness cover
Cut-out
Screw
Connector
CN11
Harness cover
Harness cover
Screw
Optional power
supply harness
supply harness
Multi rear cabinet
Screw
Screw
AC cord
Screw
AC inlet cover
AC cord
"ON"
AR-D13/D14/MU1/DC1 EXTERNAL VIEWS AND INTERNAL STRUCTURES-1
[5] EXTERNAL VIEWS AND INTERNAL STRUCTURES
A. External view
B. Internal structure
(1) AR-D13
1
Multi-purpose tray (No. 2 tray)
2
No. 3 tray
3
No. 4 tray
4
Large capacity tray
5
Desk left door
Code
Name
Function
Remark
1
TPFD1
2
TPFD2
3
TPFD3
1
AR-DU13
5
4
AR-DU14
1
5
2
3
3
AR-MU1
1
5
1.TPFD1
2.TPFD2
3.TPFD3
Click on the first or last page to see other AR-D14 service manuals if exist.