DOWNLOAD Sharp AR-D14 Service Manual ↓ Size: 3.6 MB | Pages: 44 in PDF or view online for FREE

Model
AR-D14
Pages
44
Size
3.6 MB
Type
PDF
Document
Service Manual
Brand
Device
Copying Equipment / Service Manual
File
ar-d14.pdf
Date
PREV: Sharp AR-D13 (serv.man25) Service Manual / Technical Bulletin

Sharp AR-D14 Service Manual ▷ View online

AR-D13/D14/MU1/DC1 UNPACKING AND INSTALLATION-3
<2>Attach the AC inlet cover to the rear cabinet of the stand/paper 
drawer and fix it with the removed screw.
10) Connect the AC cord of the power supply unit to the main unit of the
printer.
Connect the AC cord of the power supply unit to the inlet connector
of the main unit of the printer at the location shown in the illustration.
11) Attach the paper guides to the lower tray (large capacity tray) and set
the size.
Refer to "Setting and adjustment" described later.
12) Adjust the position of the paper guides of the upper paper tray of the
stand/paper drawer.
Refer to "Setting and adjustment" described later.
2.AR-D14
<Before installation>
•For installation, a power supply unit (AR-DC1) is needed.
1) Turn off the main switch of the main unit of the printer.
Turn the main switch located on the front side of the printer to the
"OFF" position.
Then remove the power plug from the outlet.
2) Attach the adjusters and adjust them.
<1>Insert the left adjusters to the stand/paper drawer.
<2>Turn the five adjusters to lower them until they touch the floor.
<3>Attach the four adjuster covers.
3) Put the main unit of the printer on the stand/paper drawer.
<1>Pull out the paper tray of the main unit until it stops and then remove 
it by lifting both ends of the tray.
<2>Hold the main unit of the printer at the positions shown in the 
illustration and put the main unit on the stand/paper drawer so that 
the front side and the left side of the main unit are aligned to those of 
the stand/paper drawer.
4) Connect the main unit to the stand/paper drawer.
<1>Attach the rear mounting plates with two supplied screws.
Screw
AC inlet cover
AC cord
<Parts included>
Left adjuster: 1 pc.
Front mounting
 plates: 2 pcs.
Rear mounting
 plates: 2 pcs.
Adjuster covers: 4 pcs.
Screws: 4 pcs.
"OFF"
3
3
3
3
2
2
2
2
1
Front side
Rear side
Rear mounting plate
Rear
mounting plate
Screw
Screw
AR-D13/D14/MU1/DC1 UNPACKING AND INSTALLATION-4
<2>Pull out the upper paper tray of the stand/paper drawer until it stops 
and attach the front mounting plates with two supplied screws.
Then, remove the lock of the paper tray and close the tray.
Remove the locks of the middle tray and the lower tray similarly.
<3>Reattach the paper tray of the main unit.
5) Remove the rear cabinet of the stand/paper drawer and remove the
AC inlet cover.
<1>Remove the four screws that fix the rear cabinet and then remove the 
rear cabinet.
<2>Remove the screw that fixes the AC inlet cover and then remove the 
AC inlet cover.
<3>Process the AC inlet cover as shown in the illustration.
6) Attach the power supply unit.
Attach the power supply unit to the positioning portion of the multi
purpose drawer and then fix it with three supplied screws.
7) Connect the power supply unit harness to the PCU PWB of the main
unit of the printer.
<1>Remove the screw that fixes the harness cover of the main unit of the 
printer and slide the harness cover up to remove it.
Process the harness cover as shown in the illustration.
<2>Connect the optional power supply harness connector to CN11 (red 
connector) of the PCU PWB of the main unit of the printer.
<3>Reattach the harness cover to its original position and fix it with the 
removed screw.
At this time, ensure that the optional power supply unit harness is 
arranged as shown in the illustration.
•Fix the harness securely to the wire saddle.
Screw
Screw
Front
mounting plate
Front mounting
plate
Rear cabinet
AC inlet cover
Cut out.
Power supply unit
Screws
Screws
Harness cover
Cut out.
Screw
Connector
CN11
Wire saddle
Harness cover
Optional power 
supply harness
Screw
Wire saddle
AR-D13/D14/MU1/DC1 UNPACKING AND INSTALLATION-5
8) Connect the relay harness of the stand/paper drawer to the power
supply unit.
Connect the relay harness of the stand/paper drawer to the
connector of the power supply unit.
9) Attach the rear cabinet of the stand/paper drawer.
<1>Pass the cord of the power supply unit through the hole of the rear 
cabinet and attach the rear cabinet to the stand/paper drawer.
<2>Attach the AC inlet cover to the rear cabinet of the stand/paper 
drawer and fix it with the removed screw.
10) Connect the AC cord of the power supply unit to the main unit of the
printer.
Connect the AC cord of the power supply unit to the inlet connector
of the main unit of the printer at the location shown in the illustration.
11) Adjust the position of the paper guides of the upper paper tray of the
stand/paper drawer.
Refer to "Setting and adjustment" described later.
3.AR-MU1
<Before installation>
•When installing AR-MS1, if you install a finisher or mail-bin stacker
together, a power supply unit (AR-DC1) is needed.
1) Turn off the main switch of the main unit of the printer.
Turn the main switch located on the front side of the main unit to the
"OFF" position.
Then, remove the power plug of the main unit from the outlet.
2) Put the main unit of the printer on the multi purpose drawer.
<1>Pull out the paper tray of the main unit until it stops and then remove 
it by lifting both ends of the tray.
<2>Hold the main unit of the printer at the positions shown in the 
illustration and put the main unit on the multi purpose drawer so that 
the front side and the left side of the main unit are aligned to those of 
the multi purpose drawer.
3) Connect the main unit of the printer to the multi purpose drawer.
<1>Attach the rear mounting plates with two supplied screws.
Connector of the power supply connector
Relay harness of the
stand/paper drawer
Rear cabinet
Screw
AC inlet cover
AC cord
<Parts included>
Front mounting plates: 2 pcs.
Rear mounting plates: 2 pcs.
Screws: 4 pcs.
Front side
Rear side
Rear mounting
 plate
Rear mounting plate
Screw
 Screw
AR-D13/D14/MU1/DC1 UNPACKING AND INSTALLATION-6
<2>Pull out the paper tray of the multi purpose drawer until it stops and 
attach the front mounting plates with two supplied screws.
Then, remove the lock of the paper tray and close the tray.
<3>Reattach the paper tray of the main unit of the printer.
4) Connect the harness to the main unit of the printer.
<1>Remove the screw that fixes the harness cover of the main unit of the 
printer and then slide the harness cover up to remove it.
Process the harness cover as shown in the illustration.
<2>Connect the connector of the relay harness of the multi purpose 
drawer to the connector of the PCU PWB of the main unit of the 
printer.
If you do not install a finisher, saddle stitch finisher or mail-bin stacker,
the steps below are not needed. Proceed to step 10).
5) Remove the rear cabinet of the multi purpose drawer.
<1>Remove the two screws that fix the rear cabinet of the multi purpose 
drawer and then remove the rear cabinet.
<2>Remove the screw that fixes the AC inlet cover and then remove the 
AC inlet cover.
Process the AC inlet cover as shown in the illustration.
6) Attach the power supply unit.
Attach the power supply unit to the positioning portion of the multi
purpose drawer and then fix it with three supplied screws.
7) Connect the power supply unit harness to the PCU PWB of the main
unit of the printer.
Connect the power supply harness connector to CN11 (red
connector) of the PCU PWB of the main unit of the printer.
Screw
Screw
Front mounting plate
 Front
 mounting plate
 Harness cover
Cut out.
Screw
Connector
 Rear cabinet
Screw
Screw
AC inlet cover
Cut out.
Optional power supply unit
Screws
Screws
CN11
Connector
Page of 44
Display

Click on the first or last page to see other AR-D14 service manuals if exist.

RANDOM: