Sharp AR-CS1 Service Manual ▷ View online
B. AR-DE1
Packed items
Remove the power plug of the copier from the power
outlet, then perform the following procedures.
outlet, then perform the following procedures.
1. Put the copier on the desk.
Hold the knobs of the copier and fit the desk precisely with the desk
and put the copier on the desk.
and put the copier on the desk.
Be sure to check that the positioning pins (2 pcs.) of the desk (top
front) are securely in the positioning holes.
front) are securely in the positioning holes.
Be careful that the copier and the bottom are not in contact with the
desk paper guide.
desk paper guide.
2. Remove the tray from the copier.
Pull the lower tray out until it stops.
Then hold and lift the tray to remove.
3. Connect the copier and the desk.
•
Front connection
Put the connecting plate of the desk as shown, and fix the copier
and the desk with the connecting screws (2 pcs.).
and the desk with the connecting screws (2 pcs.).
Front
Connecting plate (2 pcs.)
Connecting plate cover (2 pcs.)
Connecting screw (6 pcs.)
Portioning pins
Paper guide
Connecting plates
Connecting
screws
screws
3 – 3
•
Side connection
Attach the connecting plates to the copier and the desk with the
round hole upside. Insert the connecting screws into the round
holes and fix.
round hole upside. Insert the connecting screws into the round
holes and fix.
Insert the connecting plate cover into the external fitting of the
copier and fix the copier and the desk with the connecting screw.
(1 pc. for each)
copier and fix the copier and the desk with the connecting screw.
(1 pc. for each)
★
The connecting screw serves not only as the fixing screw but also
as an electrical grounding for the copier and the desk. Be sure to
fix the connecting screw.
Install the tray which was removed in procedure 2.
as an electrical grounding for the copier and the desk. Be sure to
fix the connecting screw.
Install the tray which was removed in procedure 2.
4. Remove the package fixture of the tray.
Hold the knob of the tray and pull out the tray from the desk until it
stops.
stops.
Turn the package fixture which is fixing the paper falling/rising plate in
the tray in the arrow direction.
the tray in the arrow direction.
When shipping it is set to A3 size.
When selecting the paper size, perform paper selection.
The procedures are the same as those of the copier.
5. Connect the desk connector.
Remove the connector cover fixing screw for connecting the desk
interface harness connector on the copier side, and remove the con-
nector cover.
interface harness connector on the copier side, and remove the con-
nector cover.
Connect the desk interface harness connector with the copier con-
nector, and tighten the screw of the connector to fix the connector.
nector, and tighten the screw of the connector to fix the connector.
6. Move the copier to the installing position.
7. Lock the caster.
Set the lock lever of the caster which is on the front lower side of the
desk in the arrow direction and lock the caster.
desk in the arrow direction and lock the caster.
8. Fix the desk to the floor.
Loosen the lock nut of the adjuster with a wrench or nippers.
Turn the adjuster in the arrow direction until it reaches the floor. Fix all
the adjusters (4 pcs.) to the floor.
the adjusters (4 pcs.) to the floor.
After fixing the adjusters, turn the lock nut fully upward.
Insert the power plug of the copier into the power outlet, and turn on
the power and perform the following procedures.
the power and perform the following procedures.
Right side
Connecting plate
Connecting screw
Connecting plate cover
Connecting screw
Left side
Connecting plate
Connecting plate
Connecting plate cover
Connecting screw
Left side
Fixture
Connector cover
Fixing screw
Desk side connector
Screw
Lock lever
Lock lever
Lock nut
Adjuster
Lock nut
Adjuster
3 – 4
C. AR-CS1
Remove the power plug of the copier from the power
outlet and perform the following procedure.
outlet and perform the following procedure.
1. Remove the rear cabinet of the desk.
Remove the fixing screws (6 pcs.) of the rear cabinet of the desk, and
remove the rear cabinet.
remove the rear cabinet.
2. Install the lift up unit.
Remove the fixing screw (section
★
) of the desk PWB mounting
plate, and open the desk PWB mounting plate.
Attach the lift up unit to the rear frame of the desk and slide it to the
left.
left.
Fix the lift up unit with the fixing screws A (3 pcs.) and connect the
desk PWB connector to the lift up unit connector.
desk PWB connector to the lift up unit connector.
Return the desk PWB mounting plate to the original position, and fix it
with the fixing screw (section
with the fixing screw (section
★
).
3. Install the rear cabinet of the desk.
Install the rear cabinet which was removed in procedure 1 to the
original position, and fix it with fixing screws (6 pcs.).
original position, and fix it with fixing screws (6 pcs.).
4. Remove the desk tray.
Pull out the tray (which is above the tray to be installed) until it stops.
Hold the both sides of the tray and lift it to remove.
5. Remove the cover.
Remove the fixing screws (2 pcs.) of the cover of the tray to be
installed, and remove the cover.
installed, and remove the cover.
Packed items
Tray rail left
(1 pc.)
Paper fed unit
(1 pc.)
Lift up unit
(1 pc.)
Tray rail right cover
(1 pc.)
Stopper left
(1 pc.)
Stopper right
(1 pc.)
Fixing screw A
(M4 x 10) (7 pcs.)
Fixing screw B
(M4 x 16) (1 (pc.)
Fixing screw (6 pcs.)
Rear cabinet
Desk PWB mounting
plate
plate
Desk mounting
plate fixing screw
plate fixing screw
Fixing screw A
Desk PWB connector
Fixing screw A
Lift up unit
Fixing screw (6 pcs.)
Rear cabinet
Fixing screw
Cover
Fixing screw
3 – 5
6. Install the tray rail left.
Insert the tray rail left into the positioning section of the frame on the
left side of the desk. Put the tray rail onto the frame and fix it with
fixing screw A (1 pc.).
left side of the desk. Put the tray rail onto the frame and fix it with
fixing screw A (1 pc.).
7. Install the paper feed unit.
Put the paper feed unit on the guide rail and push it until it stops.
Engage the front side of the paper feed unit with the positioning boss
(2 positions) of the desk frame, and fix it with the fixing screw (1 pc.).
(2 positions) of the desk frame, and fix it with the fixing screw (1 pc.).
8. Install the tray rail right cover.
Insert the positioning bosses (2 positions) of the tray rail right cover
into the positioning holes of the front frame on the right side of the
desk, and fix with the fixing screws A (2 pcs.).
into the positioning holes of the front frame on the right side of the
desk, and fix with the fixing screws A (2 pcs.).
Select the paper size according to the paper to be used.
The selecting procedure is the same as that of the main body.
9. Set the tray.
Lift the both sides of the rear of the tray, fit the tray guide with the tray
rail, and push it along the tray rail into the desk.
rail, and push it along the tray rail into the desk.
Check that the tray moves smoothly.
10. Set the tray which was removed in procedure 4.
Lift the both sides of the rear of the tray, fit the tray guide with the tray
rail, and push it along the tray rail into the desk.
rail, and push it along the tray rail into the desk.
Check that the tray moves smoothly.
11. Install the stopper.
Pull out the upper tray.
Fix the stopper left to the left tray rail with the fixing screw B (1 pc.).
Fix the stopper right tot he tray rail right cover.
Insert the power plug of the copier into the power outlet and turn on
the power. Perform the following procedure.
the power. Perform the following procedure.
Positioning section
Fixing screw A
Tray rail left
Positioning
section
section
Paper feed unit
Fixing screw A
Guide rail
Positioning boss
Positioning boss
Tray rail right cover
Fixing screws A
Positioning boss
Stopper left
Fixing screw B
Left side
Right side
Stopper right
Fixing screw
3 – 6
Click on the first or last page to see other AR-CS1 service manuals if exist.