Sharp AR-CF1 (serv.man5) Service Manual ▷ View online
4-8
CHAPTER 4 PUNCHER UNIT (OPTION) BASIC OPERATION
2) A hole is punched in the trailing edge of the second sheet.
[punch shaft stopped/
home position]
home position]
[punch shaft rotated 90˚
in the reverse direction/
hole punched]
in the reverse direction/
hole punched]
[punch shaft rotated 180˚
in the reverse direction/
punch operation completed]
in the reverse direction/
punch operation completed]
Figure 4-203
4-9
CHAPTER 4 PUNCHER UNIT (OPTION) BASIC OPERATION
2.
2-/3-hole Dual Use Type
At the home position, the punch home position sensor is ON. To punch two holes, punching of
the first sheet ends when the punch shaft half peripheral area has rotated in the forward direction
180°, and the state of the punch home position sensor has changed from OFF to ON. At this time, the
3-hole puncher is moved reciprocally in the escape direction (hole puncher rise direction) on the
remaining half peripheral area on the punch shaft. Punching of the second sheet ends when the punch
shaft half peripheral area has rotated in the reverse direction 180°, and the state of the punch home
position sensor has changed from OFF to ON. Also at this time, the 3-hole puncher is moved recip-
rocally in the escape direction (hole puncher rise direction) on the remaining half peripheral area on
the punch shaft. To punch three holes, the 2-hole puncher is moved reciprocally in the escape direc-
tion (hole puncher rise direction).
180°, and the state of the punch home position sensor has changed from OFF to ON. At this time, the
3-hole puncher is moved reciprocally in the escape direction (hole puncher rise direction) on the
remaining half peripheral area on the punch shaft. Punching of the second sheet ends when the punch
shaft half peripheral area has rotated in the reverse direction 180°, and the state of the punch home
position sensor has changed from OFF to ON. Also at this time, the 3-hole puncher is moved recip-
rocally in the escape direction (hole puncher rise direction) on the remaining half peripheral area on
the punch shaft. To punch three holes, the 2-hole puncher is moved reciprocally in the escape direc-
tion (hole puncher rise direction).
The following illustrates punching when two sheets are punched with two holes.
1) A hole is punched in the trailing edge of the first sheet.
[punch shaft stopped/
home position]
home position]
[punch shaft is rotated 90˚
in the forward direction/
hole punched]
in the forward direction/
hole punched]
[punch shaft is rotated 180˚
in the forward direction/
punch operation completed]
in the forward direction/
punch operation completed]
Sensor flag
Punch home
position
sensor
position
sensor
(PI3P)
Punch shaft
Eccentric
cam
cam
Hole
puncher
puncher
Die
Die
Sheet
Punched scrap
Figure 4-204
When two holes are punched, the 3-hole puncher is fed reciprocally in the escape direction (hole
puncher rise direction) as shown below.
puncher rise direction) as shown below.
[punch shaft stopped/
home position]
home position]
[punch shaft is rotated 90˚
in the forward direction/
hole puncher rises to
topmost position]
in the forward direction/
hole puncher rises to
topmost position]
[punch shaft is rotated 180˚
in the forward direction/
hole puncher returns to
original position]
in the forward direction/
hole puncher returns to
original position]
Figure 4-205
4-10
CHAPTER 4 PUNCHER UNIT (OPTION) BASIC OPERATION
2) A hole is punched in the trailing edge of the second sheet.
[punch shaft stopped/
home position]
home position]
[punch shaft is rotated 90˚
in the reverse direction/
hole punched]
in the reverse direction/
hole punched]
[punch shaft is rotated 180˚
in the reverse direction/
punch operation completed]
in the reverse direction/
punch operation completed]
Figure 4-206
When two holes are punched, the 3-hole puncher is fed reciprocally in the escape direction (hole
puncher rise direction) as shown below.
puncher rise direction) as shown below.
[punch shaft is rotated 90˚
in the reverse direction/
hole puncher rises to
topmost position]
in the reverse direction/
hole puncher rises to
topmost position]
[punch shaft is rotated 180˚
in the reverse direction/
hole puncher returns to
original position]
in the reverse direction/
hole puncher returns to
original position]
[punch shaft stopped/
home position]
home position]
Figure 4-207
4-11
CHAPTER 4 PUNCHER UNIT (OPTION) BASIC OPERATION
C.
Horizontal Registration Operation
Horizontal registration drive of the punch slide unit is performed by the horizontal registration
motor (M2P). The home position of the punch slide unit is detected by the horizontal registration
home position sensor (PI1P). The punch slide unit detects the trailing edge of the paper by the trailing
edge sensor (LED5, PTR5) and horizontal registration sensors (LED1 to 4, SREG1 to 4) and is
moved to the trailing edge position matched to the paper size.
home position sensor (PI1P). The punch slide unit detects the trailing edge of the paper by the trailing
edge sensor (LED5, PTR5) and horizontal registration sensors (LED1 to 4, SREG1 to 4) and is
moved to the trailing edge position matched to the paper size.
The following shows horizontal registration operation.
1) When the leading edge of the paper from the host machine is detected by the trailing edge sensor
(LED5, PTR5) on the puncher unit, the horizontal registration motor (M2P) starts to move the
punch slide unit towards the front.
punch slide unit towards the front.
Horizontal registration motor (M2P)
Sheet delivery direction
Punch slide unit
Trailing edge detection sensor
(LED5, PTR5)
(LED5, PTR5)
Sheet
Figure 4-208
Click on the first or last page to see other AR-CF1 (serv.man5) service manuals if exist.