Sharp AR-C260P (serv.man22) Service Manual / Technical Bulletin ▷ View online
Sharp Electronics (UK) Ltd., Document Systems Support
CCE-544
Replacing the waste toner box unit in the market
Replace the waste toner box unit according to the interchangeability table shown below.
The transfer belt unit can be mounted as is without reference to whether it is new or old.
The transfer belt unit can be mounted as is without reference to whether it is new or old.
Machine side
Current type
Transfer belt unit
New type
Transfer belt unit
T
o
n
e
r
c
a
s
e
p
la
te
(n
o
t
s
u
p
p
li
e
d
)
B
e
lt
C
L
l
e
v
e
r
(B
la
c
k
)
B
e
lt
C
L
l
e
v
e
r
s
p
ri
n
g
(
S
il
v
e
r)
T
o
n
e
r
c
a
s
e
p
la
te
(
s
u
p
p
li
e
d
)
B
e
lt
C
L
l
e
v
e
r
(W
h
it
e
)
B
e
lt
C
L
l
e
v
e
r
s
p
ri
n
g
(
B
la
c
k
)
Toner
case
plate
(not
supplied)
Belt CL lever (Black)
C
u
rr
e
n
t
ty
p
e
W
a
s
te
t
o
n
e
r
b
o
x
u
n
it
Belt CL lever spring (Silver)
Use these as they
are.
are.
Remove the toner
case plate from the
machine and then
mount the waste
toner box unit.
(Note 1)
case plate from the
machine and then
mount the waste
toner box unit.
(Note 1)
Toner case plate (supplied)
Belt CL lever (White)
W
a
s
te
t
o
n
e
r
b
o
x
u
n
it
N
e
w
t
y
p
e
W
a
s
te
t
o
n
e
r
b
o
x
u
n
it
Belt CL lever spring (Black)
Mount the toner
case
plate on the transfer
belt unit. (Note 2)
case
plate on the transfer
belt unit. (Note 2)
Use these as they
are (the toner case
plate is
unnecessary).
(Note 2)
are (the toner case
plate is
unnecessary).
(Note 2)
Note 1) Forgetting to remove the waste toner case reinforce plate may cause a paper jam (jam resulting
from transfer belt slip). Be sure to remove the waste toner case reinforce plate.
Note 2) The pawl of the belt CL lever after change has been abolished, so the lever is not caught in the
belt housing. However, there is no problem with this. Mount a new-type waste toner box unit on
the transfer belt unit as is. (See the figures below.)
the transfer belt unit as is. (See the figures below.)
Sharp Electronics (UK) Ltd., Document Systems Support
CCE-544
Procedure for mounting the waste toner case reinforce plate
Note) Mount the waste toner case reinforce plate on the transfer belt unit in the following procedure:
Some of the transfer belt units manufactured before and in December 2003 don’t have the screw
hole shown in Step 1. In such a case, skip Step 1 and mount the waste toner case reinforce plate in
the order of Steps 2 and 3.
the order of Steps 2 and 3.
1. Temporarily fasten the waste toner case reinforce plate to the frame of the transfer belt unit with the
screw M3x6 (XHBS730P06000).
2. Align the transfer belt unit with the waste toner case reinforce plate as shown in the figure below and
secure them with the screw M3x10 (XEBS730P10000).
3. Tighten the screw M3x6 (XHBS730P06000) more firmly and then fasten the waste toner case reinforce
plate to the place shown below with the M3x6 (XHBS730P06000).
Sharp Electronics (UK) Ltd., Document Systems Support
CCE-544
Procedure for mounting the waste toner case reinforce plate
Note) Mount the waste toner case reinforce plate on the transfer belt unit in the following procedure:
Some of the transfer belt units manufactured before and in December 2003 don’t have the screw
hole shown in Step 1. In such a case, skip Step 1 and mount the waste toner case reinforce plate in
the order of Steps 2 and 3.
the order of Steps 2 and 3.
1. Temporarily fasten the waste toner case reinforce plate to the frame of the transfer belt unit with the
screw M3x6 (XHBS730P06000).
2. Align the transfer belt unit with the waste toner case reinforce plate as shown in the figure below and
secure them with the screw M3x10 (XEBS730P10000).
3. Tighten the screw M3x6 (XHBS730P06000) more firmly and then fasten the waste toner case reinforce
plate to the place shown below with the M3x6 (XHBS730P06000).
Sharp Electronics (UK) Ltd., Document Systems Support
CCE-544
Procedure for mounting the waste toner case reinforce plate
Note) Mount the waste toner case reinforce plate on the transfer belt unit in the following procedure:
Some of the transfer belt units manufactured before and in December 2003 don’t have the screw
hole shown in Step 1. In such a case, skip Step 1 and mount the waste toner case reinforce plate in
the order of Steps 2 and 3.
the order of Steps 2 and 3.
1. Temporarily fasten the waste toner case reinforce plate to the frame of the transfer belt unit with the
screw M3x6 (XHBS730P06000).
2. Align the transfer belt unit with the waste toner case reinforce plate as shown in the figure below and
secure them with the screw M3x10 (XEBS730P10000).
3. Tighten the screw M3x6 (XHBS730P06000) more firmly and then fasten the waste toner case reinforce
plate to the place shown below with the M3x6 (XHBS730P06000).
Display
