Sharp AR-C260 (serv.man33) User Manual / Operation Manual ▷ View online
12
GENERAL PROGRAMS
■ List print
This program is used to print lists of key operator
programs.
Lists of key operator programs for copier, printer
and network scanner features are available.
programs.
Lists of key operator programs for copier, printer
and network scanner features are available.
■ Key operator code change
This program is used to change the key operator
code.
The key operator must register a key operator code
number and use the number to gain access to key
operator programs. Only one key operator code
number can be registered. The factory has
registered five zeros as the code number to allow
initial access to the programs. It is recommended
that the key operator use the factory number for
initial entry into the programs and then choose and
enter another number by this program.
code.
The key operator must register a key operator code
number and use the number to gain access to key
operator programs. Only one key operator code
number can be registered. The factory has
registered five zeros as the code number to allow
initial access to the programs. It is recommended
that the key operator use the factory number for
initial entry into the programs and then choose and
enter another number by this program.
■ Product key
Use these programs to input data required to
activate the following systems.
activate the following systems.
E-mail alert and status
This program cannot be used now. This program is
reserved for future customer support through a
network.
reserved for future customer support through a
network.
Network scanner expansion kit
This program must be used to activate the network
scanner expansion kit. For the password to be
entered, contact your dealer.
scanner expansion kit. For the password to be
entered, contact your dealer.
Serial number
Use this program to check the serial number of the
machine. This is necessary to obtain product keys
for "E-mail alert and status" and the Network
scanner expansion kit.
machine. This is necessary to obtain product keys
for "E-mail alert and status" and the Network
scanner expansion kit.
sec_whale_keyope.fm 12 ページ ２００２年１１月１３日 水曜日 午後６時０分
13
PROGRAMS FOR COPY MODE
The key operator programs that are used for copy mode are explained in the following.
■ Copy settings
OTHER FUNCTION SETTINGS
Initial status settings
The copier settings will be reset when the main
switch is turned off, when the [CA] key is pressed,
or when the auto clear interval has elapsed. Use
this program to establish new initial settings or to
return the initial settings to the factory default
settings. Paper tray, exposure mode, copy ratio,
duplex mode, and output mode default settings can
be selected.
switch is turned off, when the [CA] key is pressed,
or when the auto clear interval has elapsed. Use
this program to establish new initial settings or to
return the initial settings to the factory default
settings. Paper tray, exposure mode, copy ratio,
duplex mode, and output mode default settings can
be selected.
Exposure adjustment
Use this program to lighten or darken copies in the
automatic exposure mode. The factory setting is
"5". "1" indicates lighter density and "9" indicates
darker density on the touch panel.
automatic exposure mode. The factory setting is
"5". "1" indicates lighter density and "9" indicates
darker density on the touch panel.
Rotation copy setting
If this program is set, the image of originals will
rotate when the orientation of the originals does not
match that of the copy paper.
(Rotation copy will function only if the auto paper
select or auto image mode has been selected.)
rotate when the orientation of the originals does not
match that of the copy paper.
(Rotation copy will function only if the auto paper
select or auto image mode has been selected.)
Add or change extra preset ratios
Two extra preset copy ratios can be added within
both the reduction range (45% to 99%) and the
enlargement range (101% to 400%). Only added
preset copy ratios can be changed. The standard
preset copy ratios are fixed in memory and cannot
be changed.
both the reduction range (45% to 99%) and the
enlargement range (101% to 400%). Only added
preset copy ratios can be changed. The standard
preset copy ratios are fixed in memory and cannot
be changed.
Initial margin shift setting
Set the initial margin shift value with this program.
The value can be set from 0 mm to 20 mm in 1 mm
increments or from 0" to 1" in 1/8" increments.
If an optional duplex module/2 x 500 sheet paper
drawer (AR-D19) and duplex bypass/inverter unit
(AR-RB1) are not installed, the value for the
reverse side (side 2) is not displayed.
The value can be set from 0 mm to 20 mm in 1 mm
increments or from 0" to 1" in 1/8" increments.
If an optional duplex module/2 x 500 sheet paper
drawer (AR-D19) and duplex bypass/inverter unit
(AR-RB1) are not installed, the value for the
reverse side (side 2) is not displayed.
Erase width adjustment
Set the initial setting of the amount of the erase
area with this program.
The values can be set from 0 mm to 20 mm in 1 mm
increments or from 0" to 1" in 1/8" increments.
area with this program.
The values can be set from 0 mm to 20 mm in 1 mm
increments or from 0" to 1" in 1/8" increments.
Setting a maximum number of copies
Use this program to limit the maximum number of
copies per copy run which can be input in the copy
quantity display.
A number from 1 to 999 can be set.
copies per copy run which can be input in the copy
quantity display.
A number from 1 to 999 can be set.
NOTE
Even if the default state of the two-sided function
has been set to other than one-sided to one-sided
copy mode using this program, in the event that the
two-sided function of the optional duplex module/2
x 500 sheet paper drawer or the reversing
automatic document feeder has failed or has been
prohibited* from use, the default state will revert to
one-sided to one-sided copy mode.
has been set to other than one-sided to one-sided
copy mode using this program, in the event that the
two-sided function of the optional duplex module/2
x 500 sheet paper drawer or the reversing
automatic document feeder has failed or has been
prohibited* from use, the default state will revert to
one-sided to one-sided copy mode.
* Disabling of document feeder (page 9)
Disabling of duplex (page 9)
Disabling of inverter (page 9)
Disabling of optional paper drawer (page 9)
Disabling of inverter (page 9)
Disabling of optional paper drawer (page 9)
NOTE
For copying from A5 or 5-1/2" x 8-1/2" size originals
onto A5R or 5-1/2" x 8-1/2"R paper, this program
must be set.
onto A5R or 5-1/2" x 8-1/2"R paper, this program
must be set.
sec_whale_keyope.fm 13 ページ ２００２年１１月１３日 水曜日 午後６時０分
14
PROGRAMS FOR COPY MODE
Initial colour balance setting
Colour balance settings that have been adjusted
using the special "Colour Balance" function
explained on page 6-14 of the "Operation Manual
for general information and copier operation" can
be called up and set as initial colour balance
settings* by storing them ahead of time in a job
program (page 6-26 of the "Operation Manual for
general information and copier operation"). Use
this feature when you want to repeatedly use
settings for a favorite colour or for correction when
a change occurs in the colour balance.
* Preset values displayed when you select the
using the special "Colour Balance" function
explained on page 6-14 of the "Operation Manual
for general information and copier operation" can
be called up and set as initial colour balance
settings* by storing them ahead of time in a job
program (page 6-26 of the "Operation Manual for
general information and copier operation"). Use
this feature when you want to repeatedly use
settings for a favorite colour or for correction when
a change occurs in the colour balance.
* Preset values displayed when you select the
special "Colour Balance" function. The factory
default settings are the "0" position for all eight
levels of each colour.
default settings are the "0" position for all eight
levels of each colour.
When the [INITIAL COLOUR BALANCE
SETTING] key is touched, the following display will
appear.
SETTING] key is touched, the following display will
appear.
If a job program number key is touched that does
not have colour balance settings, a warning
message will appear.
To return colour balance settings that have been
stored as initial settings to the factory default
settings (the "0" position for all eight levels of each
colour), touch the [RETURN TO THE FACTORY
DEFAULT SETTINGS.] key.
not have colour balance settings, a warning
message will appear.
To return colour balance settings that have been
stored as initial settings to the factory default
settings (the "0" position for all eight levels of each
colour), touch the [RETURN TO THE FACTORY
DEFAULT SETTINGS.] key.
Auto colour calibration
The Auto Colour Calibration program enables
automatic colour gradation correction when the
colour is off.
automatic colour gradation correction when the
colour is off.
When the [AUTO COLOUR CALIBRATION] key is
touched, the following display will appear.
touched, the following display will appear.
After the [EXECUTE] key is touched and a test
patch printed, a message appears asking you to
begin automatic adjustment. Place the test patch
on the document glass as shown below and touch
the [EXECUTE] key.
patch printed, a message appears asking you to
begin automatic adjustment. Place the test patch
on the document glass as shown below and touch
the [EXECUTE] key.
When a message appears informing you that auto
colour calibration is completed, touch the [OK] key
to end the procedure.
colour calibration is completed, touch the [OK] key
to end the procedure.
KEY OPERATOR PROGRAMS
OK
INITIAL COLOUR BALANCE SETTING
PRESS PROGRAM NUMBER IN WHICH COLOUR BALANCE PROGRAM IS REGISTERED.
1
6
2
7
3
8
4
9
5
10
RETURN TO THE FACTORY DEFAULT
SETTINGS.
NOTE
The colour gradation may not be sufficiently
corrected after one correction cycle. If so, execute
the program again.
corrected after one correction cycle. If so, execute
the program again.
NOTE
Lay approximately five sheets of copy paper that
are the same size as the test patch on top of the set
test patch, and gently close the original cover.
are the same size as the test patch on top of the set
test patch, and gently close the original cover.
NOTE
Before executing this program, check to see if the
registration adjustment is correct. If not, execute
[AUTO ADJUSTMENT] in [Registration
adjustment] on page 10.
registration adjustment is correct. If not, execute
[AUTO ADJUSTMENT] in [Registration
adjustment] on page 10.
KEY OPERATOR PROGRAMS
OK
AUTO COLOUR CALIBRATION
USE 11"X17" OR A3 PAPER FOR THIS ADJUSTMENT.
PRESS [EXECUTE] TO PRINT THE TEST PATCH.
PRESS [EXECUTE] TO PRINT THE TEST PATCH.
EXECUTE
Cyan
Magenta
Yellow
Black
sec_whale_keyope.fm 14 ページ ２００２年１１月１３日 水曜日 午後６時０分
15
PROGRAMS FOR COPY MODE
ENABLE/DISABLE SETTINGS
Disabling deletion of job programs
This program is used to prevent stored programs
from being replaced or deleted. When this program
is set, storing of job programs is also disabled.
from being replaced or deleted. When this program
is set, storing of job programs is also disabled.
Disabling of bypass-tray in duplex copy
This program is used to disable the use of the
bypass tray when making duplex copies.
bypass tray when making duplex copies.
Disabling of covers mode
This program is used to prevent selection of the
COVERS mode.
COVERS mode.
Disabling of auto paper selection
This program is used to prevent automatic paper
selection. When automatic paper selection is
disabled, the copier will not automatically select a
paper tray containing paper that matches the size
of the original placed on the document glass or in
the optional reversing automatic document feeder.
selection. When automatic paper selection is
disabled, the copier will not automatically select a
paper tray containing paper that matches the size
of the original placed on the document glass or in
the optional reversing automatic document feeder.
sec_whale_keyope.fm 15 ページ ２００２年１１月１３日 水曜日 午後６時０分
Click on the first or last page to see other AR-C260 (serv.man33) service manuals if exist.