DOWNLOAD Sharp AR-C250 (serv.man41) Service Manual ↓ Size: 167.67 KB | Pages: 12 in PDF or view online for FREE

Model
AR-C250 (serv.man41)
Pages
12
Size
167.67 KB
Type
PDF
Document
Service Manual / Technical Bulletin
Brand
Device
Copying Equipment / Troubleshooting Copy Quality
File
ar-c250-sm41.pdf
Date

Sharp AR-C250 (serv.man41) Service Manual / Technical Bulletin ▷ View online

 
 
 
GMA050702 
Sharp Electronics (UK) Ltd., Technical Services Group
 
 
 
 
If the colour patch is judged to be abnormal, select “Repeat” to reprint the test 
pattern. 
 
 
 
Once the test pattern is rescanned and the colour patch is judged to be normal, 
press OK. Wait until the message “Please Quit This Mode” is displayed before 
exiting the test simulation. 
 
After completion of this command, make test copies using the Sharp Colour Test 
Chart (UKOG-0283FCZZ) and confirm copy quality. If the customer is satisfied with 
the quality, calibration is complete. 
 
If the copy quality is not acceptable, perform Manual Colour Balance adjustment:- 
 
 
 
 
 
 
Manual Colour Balance 
 
 
 
Test command 46-21: 
 
This adjustment needs to be performed if:- 
 
a)  You are unable to get a satisfactory result from the automatic adjustment. 
b)  To suit individual customer needs. 
 
 
Enter Test Simulation 46-21, select  “A3” paper, and verify that all values are set to 
500.
 
(After completion of TC 46-24, this is done automatically). 
 
Press “EXECUTE”. 
 
A colour patch image will be printed. Examine the printout, and determine the 
following: 
 
1)  Patch “A” of Y, C, M, and K is not visible. 
2)  Patches “B through E” are very faint. (“B” & “C” not visible is acceptable). 
3)  The patch density for each colour should change gradually from high 
density (left) to low density (right). 
4)  Each colour should be roughly equal in density. For example, Cyan should 
not be noticeably darker than Magenta, or vice- versa. 
 
Note: If the four colour “gamuts” are too intense between “G” and “A”, 
background may result.  A noticeable “drop-off” in intensity should occur near 
“G”. 
 
 
Cont’d 
 
 
 
GMA050702 
Sharp Electronics (UK) Ltd., Technical Services Group
 
 
 
 
If any of the above conditions are not met, adjust the density of each colour’s gamut 
by using the up and down arrows. This changes all 15 squares simultaneously. 
(each colour’ “gamut” is represented by 15 squares. - Letters “A” through “O”.) 
 
The next objective is to adjust the individual patch to get the composite black 
strip (CMY mixed) to match the process black strip (Bk) as closely as possible. 
 
1) 
With the first process black strip facing you, label the process black strip from 
left to right, MAX, O, N, M, L, K, J, I, H, G, F, E, D, C, B, and A. (16 squares) This 
will be your reference sheet. 
 
2) 
In order to manipulate the composite black strip so it resembles the process 
black strip as closely as possible, highlight the colour you wish to adjust (C, M, Y, or 
K). Choose the square you wish to adjust, (letter A through O) ,use the ten keys to 
increase or decrease the value, and press “OK”. 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
Select Colour 
to be adjusted 
Either Select 1 point to adjust 
1 point at a time or use the up 
and down arrows to adjust all 
15 points simultaneously
 
 
 
 
 
GMA050702 
Sharp Electronics (UK) Ltd., Technical Services Group
 
 
 
 
 
You can check and compare the result of your adjustment by pressing “EXECUTE”, 
which prints a current test pattern. 
 
Once the composite black strip (4 colour) has been adjusted, so that it is as close to 
the process black channel, exit the test simulation. 
 
In addition to suit customer requirements, the colour balance for each colour 
exposure mode can be adjusted by using Test Simulations 46-10/11/12/13/14 . 
 
These simulations are identical to test simulation 46-21, except there is no 
“EXECUTE” key. Use the Sharp colour test chart or customer samples, and switch 
between the test command and the user exposure selection to make adjustments. 
 
Press “CLOSE” to leave the simulation, make a test copy after selecting the 
appropriate exposure mode. Press, “TEST” to return to the test simulation and 
make further adjustments.  
 
To save ALL Half Tone adjustments, execute Test Simulation 44-21. Once 
complete, enter simulation 44-06 to perform compulsory engine process control:- 
 
 
Press “EXECUTE”.  
 
The “COMPLETE” box will be highlighted if process control has been performed 
successfully. 
 
If an “ERROR” occurs, repeat the simulation once, then diagnose the cause of the 
error. 
 
Using the Sharp Colour Test Chart (UKOG-0283FCZZ), make test copies and 
confirm copy quality.  
 
This concludes the colour balance adjustment(s). 
 
 
 
 
 
 
Copy Exposure 
 
 
 
 
 
Test Simulations 46-01 & 46-02 
 
 
 
 
 
The exposure adjustment in ALL colour and B/W modes must be performed 
after calibrating the engine. Failure to check or adjust the copy exposure may 
result to excessive background when copying. 
 
  
Cont’d 
 
 
 
 
 
GMA050702 
Sharp Electronics (UK) Ltd., Technical Services Group
 
 
 
 
Note: Reducing the value reduces the saturation in the low-density area and 
the white area for each copy mode. The saturation in the high-density area is 
not affected. 
 
When adjusting Test Simulations 46-01 and 46-02, it is recommended to use both 
the Sharp Colour Test Chart (UKOG-0283FCZZ) and the Sharp Grey Scale Chart 
(UKOG-0162FCZZ) to adjust the low-density area 
 
 
 
 
 
Adjust the exposure for both B/W & Colour modes as per specification:- 
 
 
 
 
 
 
COLOUR MODE 
 
 Using a Sharp Colour Test Chart, adjust each exposure mode in manual exposure 
position “3”, until row 7 of the colour bar chart is absent. This involves switching 
from Test Simulation mode to operator mode 
 
 
 
 
 
 
 
 
 
 
If each exposure mode value is adjusted by a given amount, make a test copy in all 
modes to confirm the copy quality and background level. 
“TEST” icon. 
Press “CLOSE”, to return to 
operator mode. Select the 
exposure mode you wish to 
adjust, then return to test 
command mode by pressing the 
“TEST” icon. 
Page of 12
Display

Click on the first or last page to see other AR-C250 (serv.man41) service manuals if exist.