Sharp AR-C170 (serv.man50) User Manual / Operation Manual ▷ View online
2-17
2
STORAGE OF SUPPLIES
Standard supplies for this product that can replaced by the user include paper, toner cartridges, and staple cartridges
for the finisher.
for the finisher.
■
■
■
■ Proper storage
1. Store the supplies in a location that is:
● clean and dry,
● at a stable temperature,
● not exposed to direct sunlight.
● clean and dry,
● at a stable temperature,
● not exposed to direct sunlight.
2. Store paper in the wrapper and lying flat.
3. Paper stored in packages standing up or out of
3. Paper stored in packages standing up or out of
the wrapper may curl or become damp, resulting
in paper misfeeds.
in paper misfeeds.
4. Store a new toner cartridge box horizontally. Do
not store it standing on end. If stored standing on
end, the toner may not distribute well even after
shaking the cartridge vigorously, and will remain
inside the cartridge without flowing out.
end, the toner may not distribute well even after
shaking the cartridge vigorously, and will remain
inside the cartridge without flowing out.
For best copying results, be sure to use only Sharp Genuine Supplies which are designed,
engineered, and tested to maximize the life and performance of Sharp products. Look for
the Genuine Supplies label on the toner package.
engineered, and tested to maximize the life and performance of Sharp products. Look for
the Genuine Supplies label on the toner package.
GENUINE SUPPLIES
Supply and Consumables
The supply of spare parts for a repair of the appliance is guaranteed for at least 7 years following the termination
of production. Spare parts are those parts of the apparatus which may break down within the scope of the ordinary
use of the product - whereas those parts which normally exceed the life of the product are not to be considered
as spare parts. Consumables too, are available for 7 years following the termination of production.
The supply of spare parts for a repair of the appliance is guaranteed for at least 7 years following the termination
of production. Spare parts are those parts of the apparatus which may break down within the scope of the ordinary
use of the product - whereas those parts which normally exceed the life of the product are not to be considered
as spare parts. Consumables too, are available for 7 years following the termination of production.
Apollon_general-copy_EX.book 17 ページ ２００４年６月７日 月曜日 午後１時５９分
2-18
MISFEED REMOVAL
When a misfeed has occurred during printing, the message "MISFEED HAS OCCURRED." will appear in the touch
panel display of the operation panel and printing output will stop. The approximate locations of possible misfeeds are
indicated by "
panel display of the operation panel and printing output will stop. The approximate locations of possible misfeeds are
indicated by "
" in the illustration below. The page numbers for detailed information for misfeed removal for each
are also shown.
Misfeed removal guidance
Misfeed removal guidance can be displayed by touching the [INFORMATION] key on the touch panel after a misfeed
has occurred.
has occurred.
NOTE
Received faxes are all temporarily stored in memory. If a paper misfeed occurs, received faxes cannot be printed.
When the misfeed is removed, the received faxes will print out automatically.
Received faxes are all temporarily stored in memory. If a paper misfeed occurs, received faxes cannot be printed.
When the misfeed is removed, the received faxes will print out automatically.
NOTES
● Be careful not to tear
● Be careful not to tear
the misfed paper
during removal.
during removal.
● If paper is accidentally
torn during removal,
be sure to remove all
pieces.
be sure to remove all
pieces.
● Take care not to
damage or leave
fingerprints on the
transfer belt when
removing the misfed
paper.
fingerprints on the
transfer belt when
removing the misfed
paper.
Misfeed in the fusing area,
and exit area (page 2-20)
Misfeed in the duplex
bypass/inverter unit
(page 2-22)
bypass/inverter unit
(page 2-22)
Misfeed in the saddle
stitch finisher (page 3-10)
stitch finisher (page 3-10)
Misfeed in the reversing
single pass feeder
(see page 7-2 in the "Copy
Functions" section)
single pass feeder
(see page 7-2 in the "Copy
Functions" section)
Misfeed in the transport
area (page 2-20)
area (page 2-20)
Misfeed in the bypass tray
(page 2-19)
(page 2-19)
Misfeed in the duplex
module/2 x 500 sheet
paper drawer (page 2-22)
module/2 x 500 sheet
paper drawer (page 2-22)
Misfeed in the stand/1 x 500
sheet paper drawer or the
stand/3 x 500 sheet paper
drawer
(page 2-21)
sheet paper drawer or the
stand/3 x 500 sheet paper
drawer
(page 2-21)
Misfeed in the large
capacity tray
(page 3-22)
capacity tray
(page 3-22)
Misfeed in the 500 sheet
paper drawer
(page 2-19)
paper drawer
(page 2-19)
Misfeed in the 20-bin
sorter (page 3-19)
sorter (page 3-19)
CAUTION
The fusing unit is hot. Take care in removing paper.
Upper fusing unit
Fusing unit paper guide
Transfer belt
INFORMATION
Apollon_general-copy_EX.book 18 ページ ２００４年６月７日 月曜日 午後１時５９分
MISFEED REMOVAL
2-19
2
Misfeed in the paper feed area
Misfeed in the 500 sheet paper drawer
1
Open the upper side cover.
Push the lever upward
and gently open the
cover.
and gently open the
cover.
2
Remove the misfed paper.
Be careful not to tear the
misfed paper during
removal.
misfed paper during
removal.
3
If misfed paper is not found in step 2, pull out
paper tray 1 and remove the misfed paper.
paper tray 1 and remove the misfed paper.
Be careful not to tear the
misfed paper during
removal.
misfed paper during
removal.
4
Gently close the paper tray.
Push the tray firmly all
the way into the
machine.
the way into the
machine.
5
Gently close the upper side cover.
After closing, confirm
that the misfeed
message has been
cleared and the normal
display appears.
that the misfeed
message has been
cleared and the normal
display appears.
Misfeed in the bypass tray
1
Remove the misfed paper from the bypass
tray.
tray.
Be careful not to tear the
misfed paper during
removal.
misfed paper during
removal.
2
After removing the misfed paper, open
and close the duplex bypass/inverter unit
to reset.
and close the duplex bypass/inverter unit
to reset.
Grasp the finger hold
and gently open the unit.
and gently open the unit.
After closing, confirm that
the misfeed message
has been cleared and the
normal display appears.
If the duplex bypass/
inverter unit is not
installed, close the side
cover in the same way.
the misfeed message
has been cleared and the
normal display appears.
If the duplex bypass/
inverter unit is not
installed, close the side
cover in the same way.
NOTE
Paper misfed from a paper tray may be extending out of the tray into the right side cover area. In this case if the
tray is drawn out of the machine, the paper may become torn and difficult to remove. To prevent this from
happening, always open the right side cover first and remove the misfed paper if it is extending into that area.
Paper misfed from a paper tray may be extending out of the tray into the right side cover area. In this case if the
tray is drawn out of the machine, the paper may become torn and difficult to remove. To prevent this from
happening, always open the right side cover first and remove the misfed paper if it is extending into that area.
NOTE
If paper is loaded in the bypass tray, temporarily
remove the paper and close the bypass tray before
opening the side cover.
remove the paper and close the bypass tray before
opening the side cover.
NOTE
The misfeed may have occurred inside the machine.
Check carefully and remove it.
Check carefully and remove it.
Apollon_general-copy_EX.book 19 ページ ２００４年６月７日 月曜日 午後１時５９分
MISFEED REMOVAL
2-20
Misfeed in the transport area, fusing area, and exit area
Transport area
1
Open the upper side cover and check for a
misfeed.
misfeed.
Push the lever upward
and gently open the
cover.
and gently open the
cover.
Be careful not to tear the
misfed paper during
removal.
misfed paper during
removal.
2
Gently close the upper side cover.
Exit area
1
Misfeed in the exit area
Models with an exit tray
attached to the duplex
bypass/inverter unit:
Gently remove the misfed
paper as shown in the
illustration, taking care
not to tear the paper.
attached to the duplex
bypass/inverter unit:
Gently remove the misfed
paper as shown in the
illustration, taking care
not to tear the paper.
Models without the
duplex bypass/
inverter unit:
Gently remove the misfed
paper as shown in the
illustration, taking care
not to tear the paper.
duplex bypass/
inverter unit:
Gently remove the misfed
paper as shown in the
illustration, taking care
not to tear the paper.
Upper exit tray:
Gently remove the
misfed paper as shown
in the illustration, taking
care not to tear the
paper.
Gently remove the
misfed paper as shown
in the illustration, taking
care not to tear the
paper.
Fusing area
1
Open the duplex bypass/inverter unit.
Grasp the finger hold
and gently open the unit.
and gently open the unit.
2
Remove the misfed paper as shown in the
illustrations below.
illustrations below.
If paper is misfed in the
transport area, turn roller
rotating knob A in the
direction of the arrow to
remove the misfed paper.
transport area, turn roller
rotating knob A in the
direction of the arrow to
remove the misfed paper.
If you do not find a
misfeed, open the cover
of the fusing unit and
check for a misfeed
inside the fusing unit.
misfeed, open the cover
of the fusing unit and
check for a misfeed
inside the fusing unit.
3
Misfeed in the transfer unit
If paper is misfed on the
transfer belt, remove it
gently without touching
the transfer belt. Do not
pull out the transfer unit.
transfer belt, remove it
gently without touching
the transfer belt. Do not
pull out the transfer unit.
4
Gently close the duplex bypass/inverter unit.
After closing, confirm that
the misfeed message
has been cleared and the
normal display appears.
If the duplex bypass/
inverter unit is not
installed, close the side
cover in the same way.
the misfeed message
has been cleared and the
normal display appears.
If the duplex bypass/
inverter unit is not
installed, close the side
cover in the same way.
NOTE
If paper is loaded in the bypass tray, temporarily remove the
paper and close the bypass tray before opening the side cover.
If paper is loaded in the bypass tray, temporarily remove the
paper and close the bypass tray before opening the side cover.
NOTE
The misfeed may have occurred inside the machine.
Check carefully and remove it.
The misfeed may have occurred inside the machine.
Check carefully and remove it.
NOTE
Even after clearing a misfeed, paper may remain inside
the machine on the transfer belt where it is not visible. In
this case, after visible misfeeds are removed, the paper
on the transfer belt will be automatically moved to a
position where it is visible and a misfeed will be indicated
once again on the display. Clear the misfeed as explained
in "Misfeed in the transfer unit" (step 3 on the right side of
this page). For this reason, it may be necessary to
perform the "Misfeed in the transfer unit" procedure twice.
Even after clearing a misfeed, paper may remain inside
the machine on the transfer belt where it is not visible. In
this case, after visible misfeeds are removed, the paper
on the transfer belt will be automatically moved to a
position where it is visible and a misfeed will be indicated
once again on the display. Clear the misfeed as explained
in "Misfeed in the transfer unit" (step 3 on the right side of
this page). For this reason, it may be necessary to
perform the "Misfeed in the transfer unit" procedure twice.
The fusing unit is hot. Take care in removing paper. (Do
not touch any metal parts.)
not touch any metal parts.)
The fusing unit is hot. Take care in removing paper. (Do not
touch any metal parts.)
touch any metal parts.)
The transfer unit is hot. Take care in removing paper. (Do
not touch any metal parts.)
not touch any metal parts.)
CAUTION
CAUTION
CAUTION
Apollon_general-copy_EX.book 20 ページ ２００４年６月７日 月曜日 午後１時５９分
Click on the first or last page to see other AR-C170 (serv.man50) service manuals if exist.