DOWNLOAD Sharp AR-C170 (serv.man31) Service Manual ↓ Size: 3.77 MB | Pages: 27 in PDF or view online for FREE

AR-C170M  PRINTER CONTROLLER SECTION  14 - 9

Basic setting modifies or cancels factory settings of various printer
functions according to the use conditions. 

This program is set when inhibiting print of the caution notice
page.

Used to inhibit printing of the test page.

When this is set, the printer test page (Test page print) cannot be
printed by the user setting.

This setting allows printing on A4 size paper when letter size is
requested but there is no letter size paper.

∗

Printing on letter size paper when there is no A4 size is not
allowed.

This program is used to delete all data manually from the hard
disk.

When the built-in memory is full of printer data, further printing
cannot be made. Therefore, the contents stored in the memory are
printed. This program sets the print conditions. Factory setting is
"1 set."

This program is used to set the default paper type for paper
loaded in the bypass tray in printer mode. "NONE" (a default paper
type is not selected), "PLAIN", "HEAVY PAPER", or ''TRANSPAR-
ENCY" can be selected. If "HEAVY PAPER" is selected, select
"HEAVY PAPER 1" or "HEAVY PAPER 2". If "TRANSPARENCY"
is selected, select "SPEED MODE" or "QUALITY MODE".

The factory default setting is "NONE".

The interface setting is used to set data monitoring and control of
data sent to the machine parallel port and network port.

Used to select the parallel port and the network port of the
machine. 

This program is used to set Enable/Disable of printing from the
parallel port.

This program is used to set Enable/Disable of printing from the
USB port.

This program is used to set Enable/Disable of printing from the
network port.

Basic setting

Interface setting

Network setting

Color adjustments

Caution notice page output inhibition

Test page output inhibition

A4/Letter size auto conversion

Hold data delete

Output method when built-in memory is full

Port select method
Parallel port enable setting

USB port enable setting

Network port enable setting

I/O tome-out time

IP address setting

TCP/IP Enable setting

Netware enable setting

NetBEUI enable setting

NIC reset

Auto color calibration

Printer setting store/recall

Factory setting reset

Current setting storage

Stored setting value recall

Printer setup 

Network scanner setup 

Printer Operation Manual

Network Scanner Operation Manual

Printer setting

Key operator
code input

Default paper type for bypass tray

Items to be set

Content of item

Changeover at job 
end

After completion of printing, the port is 
set to the auto selection.

Changeover after I/O 
time-out

When the time set with I/O time-out 
time (item below) is reached, the port 
is set to auto selection.

AR-C170M  PRINTER CONTROLLER SECTION  14 - 10

This program is used to interrupt connection of the port when print
data are not sent  for a certain time to the port which is in standby
for print data reception, and used to set auto selection of port or to
start the next print data in standby for printing.

I/O time-out item means the time interval between print data
reception standby and I/O time-out.

This setting is used to use the  printer as a network printer. [Net-
work setting] allows setting of the following items. After changing
the items, terminate the key operator program and turn off the
main switch. Then turn on the main switch again after a while to
enable the setting.

Used to set the IP address of this machine when is it used under
the network environment using the TCP/IP protocol. (IP address,
IP net mask, IP gateway)

Factory setting is "IP address is automatically acquired (DHCP
Enable)."

When using under the TCP/IP protocol network environment,
[TCP/IP Enable] is set to Enable.

This setting is used when the machine is used under the TCP/IP
protocol network environment.

This setting is used when the machine is used under the NetWare
protocol network environment.

This setting is used when the machine is used under the NetBEUI
protocol network environment.

Used to reset all the setting items of NIC (Network Interface Card)
to the factory setting.

Terminate the key operator program and turn off the main switch.
Then turn on the main switch again after a while to enable the set-
ting.

This program is used to automatically adjust the color tone of each
color (cyan, magenta, yellow, and black). None of these adjust-
ments affect black and white printing.

The auto color calibration program enables automatic color grada-
tion correction when the color is off.

Note: The color gradation may not be sufficiently corrected after

one correction cycle. If so, execute the program again.

When the [AUTO COLOUR CALIBRATION] key is touched, the
following display will appear.

After the [EXECUTE] key is touched and a test patch printed, a
message appears asking you to begin automatic adjustment.
Place the test patch on the document glass as shown below and
touch the [EXECUTE] key.

Notes:

• Correct adjustment will not be possible if you use the test patch

that is printed for "Auto color calibration" for the copy function or
any other document. If you attempt to use the wrong test patch,
you will return to the message screen that asks you to begin
automatic adjustment. Be sure to place only the test patch
printed out above on the document glass.

• Lay approximately five sheets of copy paper that are the same

size as the test patch on top of the set test patch, and gently
close the original cover.

When a message appears informing you that auto color calibration
is completed, touch the [OK] key to end the procedure.

Note: Before using this program, make sure that the registration is

correctly adjusted. If the registration is not correctly
adjusted, perform [AUTO ADJUSTMENT] in "Registration
adjustment".

This program is used to reset the environment setting and the key
operator program printer setting to the default setting and to store
the current setting contents. If the setting contents are changed,
the stored contents can be recalled to reset the machine to the
stored setting contents.

This program is used to reset the environment setting and the key
operator program printer setting to the default setting. After execu-
tion of this program, terminate the key operator program and turn
off the main switch. Then turn on the main switch again after a
while to enable the setting.

This program is used to store the environment setting and the key
operator program printer setting in the memory. The stored con-
tents are not deleted even the main switch is turned off. To recall
the stored contents, use [Stored setting value recall].

This program is used to recall the setting contents stored with the
program of [Current setting storage] and reset the machine to the
recalled setting.

Configuration for 3-pin jumper is shown as follows.

KEY OPERATOR PROGRAMS

OK

AUTO COLOUR CALIBRATION

USE 11"X17" OR A3 PAPER FOR THIS ADJUSTMENT.
PRESS [EXECUTE] TO PRINT THE TEST PATCH.

EXECUTE

Cyan

Magenta

Yellow

Black

Boot ROM Write Protect

JP1

Factory Default

Normal

1-2 Short

Write Protect

2-3 Short

←

Battery

JP7

Factory Default

ON

1-2 Short

←

OFF

2-3 Short

JP1

VCCWB

BOOT

3

1

L 

⇔

 H

JP7

BATTERY

1

OFF 

⇔

 ON

3

AR-C170M  PRINTER CONTROLLER SECTION  14 - 11

Custom Setting dialog is automatically set with the Original Type as follows:

• When a user changes color dialog settings, "Original Type" is set Custom.

• When Original Type item is set to "Drawing (Thin line)", Screening item is set to "Automatic" on UI. However, in this case the drivers out-

put "Drawing" mode as PJL.

Color Mode

Color

Gray Scale

Automatic

Original 
Type

Standard

 

 

 

 

 

 

 

Graphics

Photo

Drawing 
(Thin 
line)

Web 
Page

Custom

Color Rendering

UCR Selection

Black Overprint

Screening

Pure Black Text

Original Type

Standard

SHARP Color

Standard

ON

Automatic

On

Graphics

Saturation Match

High Black

On

Text/Graphics

Off

Photo

Perceptual Match (Photo)

Low Black

Off

Photo

Off

Drawing (Thin line)

Saturation Match

High Black

On

Automatic

On

Web Page

Perceptual Match (Web)

Standard

Off

Automatic

On

Custom

No Change

No Change

No Change

No Change

No Change

AR-C170M  PRINTER CONTROLLER SECTION  14 - 12

Color matching is set.

• [CMM Off]; No color matching. UCR select is invalid.

• [Perceptual Match (Photo)]; Used to print continuous grada-

tion images (photo images, etc.).
All colors (Colors within and outside printer color reproduction
gamut) are equally color-mapped.

• [Colorimetric Match]; Used to print in colors which are close to

displayed colors.
Colors which are close to displayed colors are reproduced. Col-
ors outside the reproduction gamut are color-mapped by colori-
metric match.
Colors within printer color reproduction gamut are so color-
mapped that the color difference from CRT is minimized when
print. Colors outside printer color reproduction gamut are color-
mapped by colorimetric match.
UCR select is invalid.

• [Saturation Match]; Used to print graphical presentation docu-

ments by saturation match.
Colors within printer color reproduction gamut are so color-
mapped that the color difference from CRT is minimized when
print. Colors outside printer color reproduction gamut are color-
mapped by saturation match.

• [SHARP Color]*; Used to print photo images and graphic

images together.
Colors are reproduced to express intermediate color reproduc-
tion gamut between Perceptual Match and Saturation Match.
Color-mapped to have intermediate color reproduction gamut
between Perceptual Match and Saturation Match.

• [Perceptual Match (Web)]; Used to print Web page images.

Color matching is performed so that the overall saturation of an
image is reduced and the high-density gamut is widened than
Perceptual mode.
All colors (Colors within and outside printer color reproduction
gamut) are equally color-mapped.

Note:

This process is done by PJL output.

The ratio to use black toner is set.

• [Low Black]; To output gray tint of photo which is difficult to

reproduce. 

• [Standard]* ; For photo

• [High Black]; For CAD and graphs

Restriction:

• If "Color Rendering" item is set to "Colorimetric Match" or "CMM

OFF," this item is invalid.

Note:

This process is done by PJL output.

When the background is color, whether black characters are over-
printed is set.

• [Off]*

• [On]

Note:

This process is done by PJL output.

Color matching is set.

• [Automatic]*; Automatically checks type of each area of the

image (photo or text/graphics), and output the image by chang-
ing halftone accoding to each area.

• [Photo]; Outputs all areas by halftone for photo.

• [Text/Graphics]; Ouputs all areas by halftone for text/grahics.

Note:

This process is done by PJL output.

Select whether to print black text with only black toner.

• [Off ]; Print black text with CMYK toners.

• [On]* ; Print black text with only black toner.

There are the following restrictions among Installed RAM, Color
Mode, and Print Priority by the restriction of the printer side. As for
these restrictions, the former set is preceded and the use of other
competitive settings is prohibited. When each setting is restricted
(grayout), the Information Icon is displayed to the left of each set-
ting item. If clicking such icon, the following information is dis-
played to the type 1 dialog box.

• When the Color Mode item is set to Color/Automatic, the Print

Priority item is fixed to Speed, and it is grayed out. (Default set-
ting) 

• When the Print Priority item is set Quality, the Color Mode item

is fixed to Gray Scale, and it is grayed out.

“To use this feature, set ‘Installed RAM’ to ‘256 MB RAM’ or more
(see Configuration tab), or set ‘Color Mode’ to ‘Gray Scale’ (see
Color tab).”

“To use this feature, set ‘Installed RAM’ to ‘256 MB RAM’ or more
(see Configuration tab), or set ‘Print Priority’ to ‘Speed’ (see Color
tab).”

Color Mode

Print 

Priority

Document 

Style

Installed Memory

128MB

256MB or 

more

Color/

Automatic

Quality

1-Sided

X

O

2-Sided

X

O

Speed

1-Sided

O

O

2-Sided

O

O

Gray Scale

Quality

1-Sided

O

O

2-Sided

O

O

Speed

1-Sided

O

O

2-Sided

O

O

Gray Scale

Quality

1-Sided

O

O

2-Sided

O

O

Speed

1-Sided

O

O

2-Sided

O

O