DOWNLOAD Sharp AR-C150 (serv.man42) Service Manual ↓ Size: 167.67 KB | Pages: 12 in PDF or view online for FREE

Model
AR-C150 (serv.man42)
Pages
12
Size
167.67 KB
Type
PDF
Document
Service Manual / Technical Bulletin
Brand
Device
Copying Equipment / Troubleshooting Copy Quality
File
ar-c150-sm42.pdf
Date

Sharp AR-C150 (serv.man42) Service Manual / Technical Bulletin ▷ View online

 
 
 
GMA050702 
Sharp Electronics (UK) Ltd., Technical Services Group
 
 
 
 
 
You can check and compare the result of your adjustment by pressing “EXECUTE”, 
which prints a current test pattern. 
 
Once the composite black strip (4 colour) has been adjusted, so that it is as close to 
the process black channel, exit the test simulation. 
 
In addition to suit customer requirements, the colour balance for each colour 
exposure mode can be adjusted by using Test Simulations 46-10/11/12/13/14 . 
 
These simulations are identical to test simulation 46-21, except there is no 
“EXECUTE” key. Use the Sharp colour test chart or customer samples, and switch 
between the test command and the user exposure selection to make adjustments. 
 
Press “CLOSE” to leave the simulation, make a test copy after selecting the 
appropriate exposure mode. Press, “TEST” to return to the test simulation and 
make further adjustments.  
 
To save ALL Half Tone adjustments, execute Test Simulation 44-21. Once 
complete, enter simulation 44-06 to perform compulsory engine process control:- 
 
 
Press “EXECUTE”.  
 
The “COMPLETE” box will be highlighted if process control has been performed 
successfully. 
 
If an “ERROR” occurs, repeat the simulation once, then diagnose the cause of the 
error. 
 
Using the Sharp Colour Test Chart (UKOG-0283FCZZ), make test copies and 
confirm copy quality.  
 
This concludes the colour balance adjustment(s). 
 
 
 
 
 
 
Copy Exposure 
 
 
 
 
 
Test Simulations 46-01 & 46-02 
 
 
 
 
 
The exposure adjustment in ALL colour and B/W modes must be performed 
after calibrating the engine. Failure to check or adjust the copy exposure may 
result to excessive background when copying. 
 
  
Cont’d 
 
 
 
 
 
GMA050702 
Sharp Electronics (UK) Ltd., Technical Services Group
 
 
 
 
Note: Reducing the value reduces the saturation in the low-density area and 
the white area for each copy mode. The saturation in the high-density area is 
not affected. 
 
When adjusting Test Simulations 46-01 and 46-02, it is recommended to use both 
the Sharp Colour Test Chart (UKOG-0283FCZZ) and the Sharp Grey Scale Chart 
(UKOG-0162FCZZ) to adjust the low-density area 
 
 
 
 
 
Adjust the exposure for both B/W & Colour modes as per specification:- 
 
 
 
 
 
 
COLOUR MODE 
 
 Using a Sharp Colour Test Chart, adjust each exposure mode in manual exposure 
position “3”, until row 7 of the colour bar chart is absent. This involves switching 
from Test Simulation mode to operator mode 
 
 
 
 
 
 
 
 
 
 
If each exposure mode value is adjusted by a given amount, make a test copy in all 
modes to confirm the copy quality and background level. 
“TEST” icon. 
Press “CLOSE”, to return to 
operator mode. Select the 
exposure mode you wish to 
adjust, then return to test 
command mode by pressing the 
“TEST” icon. 
 
 
 
GMA050702 
Sharp Electronics (UK) Ltd., Technical Services Group
 
 
 
 
 
 
 
 
 
 
 
 
 
BLACK & WHITE MODE 
 
 
 
 
 
Using the Sharp Grey scale chart, adjust the B/W exposure mode using  
    Sim 
46-02:- 
 
 
 
 
 
 
Note: The AR-C160 should be adjusted to the same level as AR-C250. 
 
After completion, make test copies using the Sharp Colour Test Chart. If the 
customer is satisfied with the quality, engine calibration is complete. 
 
If an AR-PE1 or PE2 Print Controller is installed, the controller MUST be re-
calibrated, once engine calibration is finished. 
Adjust each exposure 
mode until row 7 is 
absent 
 
 
 
GMA050702 
Sharp Electronics (UK) Ltd., Technical Services Group
 
 
 
 
 
Description: 
Troubleshooting excessive Background when copying and printing. 
 
 
 
 
 
Excessive background can be caused by one or more of the following:- 
 
1. 
Incorrect Developer set-up. 
2. 
Over toning (in low humidity environment). 
3. 
Incorrect exposure adjustment. 
4. 
Incorrect Colour Balance adjustment. 
 
 
 
 
 
Developer Setup: 
 
 
 
 
 
Ensure ALL developer is acclimatised first before installation. 
 
 
 
 
 
Machine OverToning in Low Humidity Environments 
 
Ensure ALL engine firmware is at the latest level, as stated previously within this 
bulletin. (The toner correction “look up” table has been changed). 
 
To reduce the toner concentration of the developer, use Secret Test Simulation 80-
02 and increase all values by at least 10 points (CMYK). The excess toner will then 
need to be removed from the developer units by executing Test Simulation 64-01  
 
Use the following settings:- 
 
 
 
 
 
Test Pattern  
13 
  Density 
255 
  Multi 
Count  10 
 
 
Paper 
A3 or A4. 
  Colour 
CMYK 
 
Once complete, perform Compulsory Process Control (Sim 44-06) and Colour 
Calibration (Sim 46-24).  
 
Exposure Adjustment 
 
Use Test Simulations 46-01 & 46-02 to adjust the exposure in both colour and B/W 
modes as per specification. 
 
Colour Balance 
 
In addition to the colour balance adjustment stated earlier within this bulletin, the 
following should ONLY be performed when excessive background is present:- 
 
 
 
 
 
Manual Calibration (Test command 46-21) 
 
After printing the first manual calibration printout, fold the page in half. (Notice that 
the gamuts for Cyan, Magenta, Yellow and Black drop off to the right of the fold.) 
 
Using the up/down arrows, adjust all four gamuts until they drop off at or near the 
fold. 
 
Note: Moving the drop-off point to the left reduces density in the full-tone and half-
tone areas, and moving the drop-off point to the right increases density in the 
background areas. 
 
  
 
 
 
Cont’d 
 
 
 
 
Page of 12
Display

Click on the first or last page to see other AR-C150 (serv.man42) service manuals if exist.