DOWNLOAD Sharp AR-5316E (serv.man3) Service Manual ↓ Size: 1.21 MB | Pages: 19 in PDF or view online for FREE

AR-5316/5320 SIMULATIONS 7-4

22

22

SPF jam counter display

The SPF jam counter value is displayed.  (Alternate display by 3 digits)When the [Interrupt] key is 
pressed, the machine goes into the sub code input standby mode. When the [CA] key is pressed, the 
simulation is terminated.

44

34

Transfer current setting

Used to set the transfer current for the front surface and that for the back surface. When this 
simulation is executed, the current set value is displayed on the 7-seg display. Select the set value 
with the zoom (Up/Down) keys and press the [START] key, and the set content is written into the 
EEPROM and the machine goes into the sub code input standby mode. Press the [Mode select] key 
to select each setting mode. At that time, the setup content is written into the EEPROM. 
The set range is 90uA ~ 360uA in the increment of 10uA.

*

Small size paper must be Letter R (A4R) or smaller.

*

For the special size of tray, use the normal size width. 

49

01

Flash ROM program writing mode

(Operating procedure)
When this simulation is executed, "d" is displayed on the copy quantity display and the machine 
enters the Flash ROM program writing mode. Use the writing tool on the PC to write the program. 
During writing, the display is made as follows. After completion of downloading, turn OFF/ON the 
power to reset. 

 *

"*" in the error display indicates the error position. 

12

Standby mode fusing fan RPM 
setting

When this simulation is executed, the currently set code number is displayed. 
When [MODE SELECT] key is pressed, the normal setting and the high fusing temperature setting 
are switched alternatively. 
Enter the code number and press START key, and the number is written into the EEPROM and the 
machine goes into the sub code entry standby mode.

Main 
code

Sub 

code

Contents

Details of operation

Display lamp

Setting mode 

AE mode lamp
AE mode lamp & PHOTO mode lamp
AE & TEXT & PHOTO mode lamps

Normal size width: Front
Small size width: Front
Manual paper feed

Status

Copy quantity display

Pre-heat lamp

Ready lamp

Download data reception
Data delete start
Data writing (Boot section)
Data writing (Program section)
Sum check
Completion of downloading
Error status

"d"
"d"
"d"
"d"
"d"
"OFF"
"*E"

ON
ON
Flash
Flash
ON
OFF
OFF

OFF
ON
OFF
Flash
ON
OFF
OFF

00

Data receive error

07

Sum check error (Program section)

02

FLASH ROM delete error

08

Sum check error (EEPROM section)

03

FLASH ROM write error (Boot section)

09

E2PROM verify error

04

FLASH ROM write error (Program section)

0b

E2PROM verify error

05

Sum check error (Loader section)

0F Download data length error

06

Sum check error (Boot section)

Display lamp

Setting mode

Default

AE mode lamp

Normal temperature control (190°C or less)

Low speed rotation

TEXT mode

Fusing temperature of 190°C or above

High speed rotation

Code number

Setting

0
1

Low speed rotation
High speed rotation

[07]SIMULATIONS.fm  4 ページ  ２００３年１２月１９日　金曜日　午後３時２６分

AR-5316/5320 SIMULATIONS 7-5

51

02

Resist amount adjustment 

Used to adjust the contact pressure of the machine resist roller and the RSPF resist roller onto the 
paper. 
(Operating procedure)
When this simulation is executed, the current set value is displayed. 
When the exposure mode key is pressed, the following set items are changed sequentially. Enter an 
adjustment value with the 10-key and press the [START] key, and the entered value will be saved and 
a copy will be made. (Adjustment range: 1 ~ 99, Default: 50)
When the [CA] key is pressed, the entered value is saved and the simulation is terminated. 

Supported for the installed models only. Skipped for the models without installation.

53

10

SPF scan position change-over 
setting

Used to change over the scan position depending on that the SPF unit and the SPF document glass 
holder section are of anti-dirt glass or not. 
When this simulation is executed, the currently set code number is displayed. 
Enter the code number corresponding to the SPF unit to be used and press [START] key, and the 
setting will be changed over.

Though this setting is changed, the other set values are not affected. (The other set values remain 
unchanged.)
When replacing and installing the SPF unit, it is recommendable to use this simulation to set the 
scan position and execute the scan position automatic adjustment. 

64

01

Self print

The optical system status is ignored and a self print is made. Also when a print command is sent 
from the host, printing is performed. 

When this simulation is executed, warm-up is performed and the ready lamp is lighted. 
(However, the scanner is invalid and no initial operation is made.)
Enter the code number with the 10-key, and select a cassette with the cassette select key and press 
the [START] key. The selected cassette start paper feed and printing is performed in the selected 
pattern.

*

Only the tray lamp and the online lamp are lighted, and no other lamps are lighted. 

Printing is made in 1 by 2 mode, where one line is printed and the following two liens are not printed, 
or in the grid pattern. 

*

Input disable for 4 ~ 99

*

Print data are made on A3 size. (A3 paper is preferable.)

Main 
code

Sub 

code

Contents

Details of operation

Lighting lamp

Adjustment mode

AE, Main cassette lamp
AE, 2nd cassette lamp
AE, Manual paper feed lamp
AE, TEXT, PHOTO lamps

Main cassette paper feed

2nd cassette paper feed

Manual paper feed

SPF document feed (Front surface)

Code No.

Mode

0

Set to the scan position of the current mass production SPF unit. (Default)

1

Set to the scan position of the ant-dirt SPF unit. 

Code number

Pattern

0
1
2
3

1 by 2
Grid pattern
White paper
Black background

[07]SIMULATIONS.fm  5 ページ  ２００３年１２月１９日　金曜日　午後３時２６分

AR-5316/5320 USER PROGRAMS 8-1

The user programs allow the parameters of certain functions to be set, changed, or canceled as desired.

This copier has the following user programs. 

*1 On models with a SPF.

*2 On model with the two trays.

Program name

Program 

No

Description

Default

Parameters

Auto clear time

1

"Auto clear time" automatically returns the copy settings to the initial 
settings when a certain period of time elapses after a copy is made. 
This program is used to select the period of time. "Auto clear time" 
can also be disabled.

60sec

1 (OFF)

2 (10sec)

3 (20sec)

4 (60sec)

5 (90sec)

6 (120sec)

Preheat mode

2

This function automatically switches the machine to a low power 
consumption state if the set duration of time elapses without the 
machine being used when the power is on.
The POWER SAVE indicator lights up, however, the keys on the 
operation panel can be used. Normal operation automatically 
resumes when a key on the operation panel is pressed, a print job is 
received or an original is placed. 

1min

1 (1min)

2 (5min)

3 (30min)

4 (60min)

5 (120min)

6 (240min)

Auto power shut-off timer

3

This function automatically switches the machine to a state that 
consumes even less power than preheat mode if the set duration of 
time elapses without the machine being used when the power is on. 
All lights except the POWER SAVE indicator and ON LINE indicator 
go off. To resume normal operation, press the [START] key. Normal 
operation also resumes automatically when a print job is received or 
scanning is begun from a computer. While in auto power shut-off 
mode, no keys (except the [START] key) can be used.

5min

1 (5min)

2 (30min)

3 (60min)

4 (120min)

5 (240min)

Stream feeding mode *

1

4

When copying using the SPF, during the period of time that the SPF 
indicator blinks after an original has been scanned (about 5 
seconds), a subsequent original can be placed and automatically 
fed into the machine.

OFF

0 (OFF)

1 (ON)

Auto power shut-off 
setting

5

Use this setting to enable or disable auto power shut-off.

ON

0 (OFF)

1 (ON)

Auto paper select mode *

2

8

This function automatically selects paper that is the same size as 
the original placed in the SPF, or the same size as that selected with 
the [ORIGINAL SIZE ENTER] key. The function can be disabled.

ON

0 (OFF)

1 (ON)

Auto tray switching *

2

9

If the paper runs out during printing and there is paper of the same 
size and orientation in another tray, this function automatically 
switches to that tray (excluding the bypass tray). The function can be 
disabled.

ON

0 (OFF)

1 (ON)

Auditing mode

10

Use to enable or disable "Auditing mode".
"Auditing mode" is initially disabled.

OFF

0 (OFF)

1 (ON)

Account number entry

11

Use to set up account numbers. 
Up to 20 accounts can be established.

-

-

Account number change

12

Use to change an account number.

-

-

Account number deletion

13

Use to delete an account number.
A single account number can be deleted, or all account numbers at 
once.

Delete 

single 

account

0 (Delete single account)

1 (Delete all accounts)

Number of copies per 
account

14

This displays the number of copies made by each account.
The maximum count is 49,999. If this number is exceeded, the count 
will start over from 0.

-

-

Resetting account

15

Use to reset the copy count of an account to 0.
The copy count of a single account or of all accounts can be reset.

Reset single 

account

0 (Reset single account)

1 (Reset all accounts)

Resolution in Auto/Text 
mode

23

This setting is used to change the copy resolution in AUTO and 
TEXT mode from 600 x 300 dpi to 600 x 600 dpi 
(high-quality mode).
Scanning is slower when high-quality mode is used.

300dpi

1 (300dpi)

2 (600dpi)

[08]USERPROGRAMS.fm  1 ページ  ２００３年１２月１９日　金曜日　午後３時２７分

AR-5316/5320 USER PROGRAMS 8-2

Program name

Program 

No

Description

Default

Parameters

Key auto repeat

25

Use this setting to select whether or not holding down a key causes 
repeated input of the key. For keys that normally cause a set value to 
increase when held down (for example, holding down the [ZOOM] 
key), this program can be used to have the set value not change 
when the key is held down.

ON

0 (OFF)

1 (ON)

Key press time

26

Use this setting to select how long a key must be pressed for the 
input to be accepted. By selecting a longer time, you can prevent 
settings from being changed by the accidental pressing of a key.

Minimum 

(current 

response 

speed)

1 (Minimum
(current response speed))

2 (0.5sec)

3 (1.0sec)

4 (1.5sec)

5 (2.0sec)

Audible signals volume

27

This sets the volume of beep signals.

short beep

1 (short beep)

2 (long beep)

3 (OFF)

Base setting beep signal

28

Use this to sound a beep when a base setting is selected.

OFF

0 (OFF)

1 (ON)

Number of copies limit

29

Use this setting to select 99 or 999 for the maximum number of 
copies.

999 copies

1 (99 copies)

2 (999 copies)

Use close paper size

30

When this function is enabled, printing in printer mode will 
automatically continue using a different size of paper if the specified 
size of paper runs out in all trays. This feature does not function in 
copy mode.

OFF

0 (OFF)

1 (ON)

Default tray setting

31

Use this program to select a default tray. This tray is automatically 
selected each time the power is turned on or each time the machine 
reverts to the initial settings.

Upper 

paper tray

1 (Upper paper tray)

2 (Lower paper tray)

5 (Bypass tray)

Default exposure mode

32

Use this program to set "AUTO", "TEXT", or "PHOTO" as the default 
exposure mode.

AUTO

1 (AUTO)

2 (TEXT)

3 (PHOTO)

[08]USERPROGRAMS.fm  2 ページ  ２００３年１２月１９日　金曜日　午後３時２７分