DOWNLOAD Sharp AR-5316E (serv.man3) Service Manual ↓ Size: 1.21 MB | Pages: 19 in PDF or view online for FREE

AR-5316/5320 UNPACKING AND INSTALLATION 5-1

Follow these steps to change a tray's paper size setting.

Note:
•The paper size setting cannot be changed when the machine has

stopped temporarily due to running out of paper or a misfeed, or during

interrupt copying.

•During printing (even in copy mode), the paper size setting cannot be

changed.

•A5 size paper can only be selected in upper paper tray.
•Do not load paper that is a different size than the paper size setting.

Copying will not be possible.

1) Hold down the [PAPER SIZE ENTER] key for more than 5 seconds to

set the selected paper size.

The currently selected paper feed location indicator will blink and the
corresponding paper size (which is currently set) indicator will light

steadily.

All other indicators will go out.

2) If the machine has two paper trays, use the [TRAY SELECT] key to

select the paper tray for which you wish to change the paper size
setting.

Each time the [TRAY SELECT] key is pressed, a paper tray will be

indicated with a blinking paper feed location indicator.

3) Use the [ORIGINAL SIZE ENTER] key to select the paper size.

The indicator of the selected paper size lights up.

4) Squeeze the lock lever of the front guide and slide the front guide to

match the width of the paper, and move the left guide to the

appropriate slot as marked on the tray.

•The front guide is a slide-type guide. Grasp the locking knob on the

guide and slide the guide to the indicator line of the paper to be loaded.

•The left guide is an insert-type guide. Remove it and then insert it at the

indicator line of the paper to be loaded.

•When using 11" x 17" sized paper store the left guide in the slot at the

left front of the paper tray.

5) Press the [START] key and then the [PAPER SIZE ENTER] key.

To change the paper size setting of another tray, repeat steps 2) to 5)

after pressing the [START] key.

Note: Affix the paper size label for the paper size selected in step 3) to

the label position on the right end of the tray.

•Make sure that the tray's paper size setting is the same as the tray's

paper size setting in the printer driver. For example, if the tray's paper

size setting is A4R, set "Setting Paper Size" to "A4-R". For more
information, see "CONFIGURING THE PRINTER DRIVER" in the

"Software Setup Guide".

A3
A4
A4
A5
B4

XTRA

ENTER

A3
A4
A4
A5
B4

TRA

Left guide

Front guide

[05]UNPACKING.fm  1 ページ  ２００３年１２月１９日　金曜日　午後３時２６分

AR-5316/5320 SIMULATIONS 7-1

Perform the following procedure to enter the simulation mode.
"#" key 

 Interrupt key 

 "C" key 

 Interrupt key 

 

Main code 

 Start key 

 Sub code 

 Start key

When the clear all key is pressed, the simulation mode is cancelled.

When the interruption key is pressed, the process is interrupted and the
screen returns to the sub code entering display.

*

After canceling the simulation mode, be sure to turn OFF/ON the

power and check the operation.

Note: If the machine is terminated by a jam error or paper empty during

copying in the adjustment by the simulation, recopying is required. 

Main 
code

Sub 

code

Contents

01

01

Mirror scanning operation

02

Mirror home position sensor (MHPS) status display

06

Mirror scanning operation aging

02

01

Single paper feeder (SPF) aging

02

SPF sensor status display

03

SPF motor operation check

08

SPG paper feed solenoid operation check 

11

SPF PS release solenoid operation check 

05

01

Operation panel display check 

02

Fusing lamp and cooling fan operation check 

03

Copy lamp lighting check 

06

01

Paper feed solenoid operation check 

02

Resist roller solenoid operation check

10

Cassette semi-circular roller cleaning

07

01

Warm-up display and aging with jam

06

Intermittent aging

08

Shifting with warm-up display 

08

01

Developing bias output

02

Main charger output (Grid = HIGH)

03

Main charger output (Grid = LOW)

06

Transfer charger output

10

-

Toner motor operation 

14

-

Trouble cancel (except for U2) 

16

-

U2 trouble cancel

20

01

Maintenance counter clear

21

01

Maintenance cycle setting

02

Mini maintenance cycle setting

22

01

Maintenance counter display

02

Maintenance preset display

03

Jam memory display

04

Jam total counter display

05

Total counter display

06

Developing counter display

07

Mini maintenance preset display

08

SPF counter display 

09

Paper feed counter display

12

Drum counter display

13

CRUM type display

14

P-ROM version display

22

15

Trouble memory display

17

Copy counter display

18

Printer counter display

21

Scanner counter display

22

SPF jam counter display

24

01

Jam total counter clear

02

Trouble memory clear

04

SPF counter clear

06

Paper feed counter clear

07

Drum counter clear

08

Copy counter clear

09

Printer counter clear

13

Scanner counter clear

14

SPF jam total counter clear

25

01

Main motor operation check

10

Polygon motor operation check 

26

02

Size setting

03

Auditor setting

05

Count mode setting

06

Destination setting

07

Machine condition check (CPM)

18

Toner save mode setting

30

CE mark conformity control ON/OFF

31

Auditor mode exclusive setup

36

Cancel of stop at maintenance life over

37

Cancel of stop at developer life over

38

Cancel of stop at drum life over

39

Memory capacity check

42

Transfer ON/OFF timing control setting

43

Side void amount setting

51

Copy temporary stop function setting

30

01

Paper sensor status display

42

01

Developing counter clear

43

01

Fusing temperature setting

12

Standby mode fusing fan rotation setting

13

Fusing paper interval control allow/inhibit setting

44

34

Transfer current setting

40

Setting of rotation time before toner supply

46

01

Copy density adjustment (300dpi)

02

Copy density adjustment (600dpi)

09

Copy exposure level adjustment, individual setting 
(Text) 300dpi

10

Copy exposure level adjustment, individual setting 
(Text) 600dpi

11

Copy exposure level adjustment, individual setting 
(Photo) 600dpi

18

Image contrast adjustment (300dpi)

19

Exposure mode setting
(Gamma table setting/AE operation mode setting/
Photo image process setting)

20

SPF exposure correction

29

Image contrast adjustment (600dpi)

30

AE limit setting

31

Image sharpness adjustment

48

01

Main scanning magnification ratio adjustment

05

SPF/RSPF mode sub scanning magnification ratio 
adjustment in copying

49

01

Flash ROM program writing mode

12

Standby mode fusing fan RPM setting

Main 
code

Sub 

code

Contents

[07]SIMULATIONS.fm  1 ページ  ２００３年１２月１９日　金曜日　午後３時２６分

AR-5316/5320 SIMULATIONS 7-2

50

01

Image lead edge adjustment

06

Copy lead edge position adjustment (SPF/RSPF)

10

Paper off-center adjustment

12

Document off-center adjustment 

51

02

Resist amount adjustment

53

08

SPF scanning position automatic adjustment

10

SPF scan position change-over setting

61

03

HSYNC output check 

63

01

Shading check

07

SPF automatic correction

64

01

Self print

Main 
code

Sub 

code

Contents

Main 
code

Sub 

code

Contents

Details of operation

01

06

Mirror scanning operation aging

When the [START] key is pressed, the mirror base performs A3 full scanning at the set magnification 
ratio speed. During scanning, the set magnification ratio is displayed. After 3 seconds, the mirror 
base performs full scanning again. During scanning, the set magnification ratio is displayed. 

*

When the [START] key is pressed again, the ready lamp turns and remains off. 
The DV replacement/OPC drum cartridge replacement lamp displays the status of the mirror
home position sensor. (The lamp lights up when the mirror is in the home position.)
During aging, the copy lamp lights up. When the [Interrupt] key is pressed, the operation is
interrupted if operating, and the machine goes into the sub code input standby mode. 

02

01

Single paper feeder (SPF) aging

When the [START] key is pressed, the set magnification ratio is acquired and document transport 
operation of single surface is performed in the case of SPF or document transport operation of 
duplex surfaces is performed. During operation, the LED on the display section corresponding to the 
selected magnification ratio lights up, and the magnification ratio is displayed on the 7-seg display. 
When the [Interrupt] key is pressed at that time, the machine goes to the sub code input standby 
mode. When the [CA] key is pressed, the simulation is terminated. 

02

SPF sensor status display

(In order to receive the sensor change notification, the load must be decreased.)
The sensor status (ON/OFF) in the SPF can be checked with the following lamps.
When a sensor detects paper, it turns on. The open/close detection sensor turns on when the 
machine is opened. 

When the [Interrupt] key is pressed, the machine goes to the sub code input standby mode. 
When the [CA] key is pressed, the simulation is terminated. 

06

01

Paper feed solenoid operation 
check 

When this simulation is executed, the sub code is displayed on the 7-seg LED and the lamp 
corresponding to the solenoid lights up. 
Select a solenoid with the tray select key (the lamp corresponding to the solenoid lights up) and 
press the [START] key, and the machine repeats operation of ON for 500ms and OFF for 500ms.
This operation is repeated 20 times.
After that, the machine goes into the sub code entry standby mode. 
When [INTERRUPT] key is pressed during the process, the machine goes into the sub code input 
standby mode. When [CA] key is pressed, the simulation is terminated.

Display lamp

Sensor

Toner supply lamp
Copier jam lamp
The DV replacement/OPC drum cartridge 
replacement lamp
Paper empty lamp
SPF jam lamp
Manual paper feed lamp
Tray jam lamp
AE lamp
TEXT lamp
PHOTO lamp

SPF document set sensor
SPF document transport sensor
SPF unit (OC cover) open/close sensor

SPF paper exit sensor
SPF paper feed cover open/close sensor
SPF paper length sensor 1
SPF paper length sensor 2
SPF paper feed width sensor (small)
SPF paper feed width sensor (middle)
SPF paper feed width sensor (large)

*

Supported for the installed models only. Skipped for the models without installation.

Display lamp

Solenoid

Main cassette lamp 
2nd cassette lamp
Manual paper feed lamp
2nd cassette jam lamp
Machine jam lamp & 2nd cassette jam lamp

Main cassette paper feed solenoid
* 2nd cassette paper feed solenoid
Manual paper feed solenoid
* 2nd cassette paper transport solenoid
* 3rd cassette transport solenoid

[07]SIMULATIONS.fm  2 ページ  ２００３年１２月１９日　金曜日　午後３時２６分

AR-5316/5320 SIMULATIONS 7-3

06

02

Resist roller solenoid operation 
check

When the [START] key is pressed in the sub code input state, the resist solenoid (RRS) turns ON for 
500ms and OFF for 500ms. This operation is repeated 20 times. 
After completion of the process, the machine goes into the sub code input standby mode. 
When [INTERRUPT] key is pressed during the process, the machine goes into the sub code input 
standby mode. When [CA] key is pressed, the simulation is terminated.

10

Cassette semi-circular roller 
cleaning

First of all, remove the developer unit. 
Enter the simulation code, specify the cassette to be cleaned with the tray select key, and press 
START button. The main motor rotates to move the cassette semi-circular roller by half circle and 
make the roller face downward. 
After completion of cleaning, when INTERRUPT key is pressed, the machine goes into the sub code 
entry standby mode and the roller returns to the original positions. 
To clean another roller continuously, press INTERRUPT key to return the roller to the original 
position, and execute the simulation again. 
During the operation, the sub code is displayed on the display. 
*

When CA key is pressed, the simulation mode is terminated. 

However, the roller returns to the original position by the initial operation.

08

01

Developing bias output

When the [START] key is pressed, the developing bias signal is turned ON for 30 sec. 
However, to calculate the actual output value is calculated, execute SIM25-01.
After completion of the process, the machine goes into the sub code input standby mode. 
When [INTERRUPT] key is pressed during the process, the machine goes into the sub code input 
standby mode. When [CA] key is pressed, the simulation is terminated.

02

Main charger output (Grid = HIGH) When the [START] key is pressed, the main charger output is supplied for 30 sec in the grid voltage 

HIGH mode. After completion of the process, the machine goes into the sub code input standby 
mode.
When [INTERRUPT] key is pressed during the process, the machine goes into the sub code input 
standby mode. When [CA] key is pressed, the simulation is terminated.

03

Main charger output (Grid = LOW) When the [START] key is pressed, the main charger output is supplied for 30 sec in the grid voltage 

LOW mode. After completion of the process, the machine goes into the sub code input standby 
mode.
When [INTERRUPT] key is pressed during the process, the machine goes into the sub code input 
standby mode. When [CA] key is pressed, the simulation is terminated.

06

Transfer charger output

Select an output mode with the [Mode select] key and press the [START] key. The transfer charger 
output is delivered for 30 sec in the selected mode. 
After 30 sec of transfer charger output, the machine goes into the sub code entry standby mode. 
When [INTERRUPT] key is pressed during the process, the machine goes into the sub code input 
standby mode. When [CA] key is pressed, the simulation is terminated.

22

01

Maintenance counter display

The maintenance counter value is displayed. (Alternate display by 3 digits)

04

Jam total counter display

The jam total counter value is displayed. (Alternate display by 3 digits)

05

Total counter display

The total counter value is displayed.  (Alternate display by 3 digits)

06

Developing counter display

The developing counter data is acquired and displayed on the 7-seg display.  (Alternate display by 3 
digits)
When the [Interrupt] key is pressed, the machine goes into the sub code input standby mode. 
When the [CA] key is pressed, the simulation is terminated.

08

SPF counter display 

The SPF counter value is displayed.  (Alternate display by 3 digits)

14

P-ROM version display

The P-ROM version is displayed on the copy quantity display. The main code and the sub code are 
alternatively displayed by 2 digits. The display interval is same as that of the counter display. 
By pressing the fixed magnification ratio key, each version display is switched. 

17

Copy counter display

The copy counter value is displayed. (Alternate display by 3 digits) When the [Interrupt] key is 
pressed, the machine goes into the sub code input standby mode. When the [CA] key is pressed, the 
simulation is terminated.

18

Printer counter display

The printer counter value is displayed.  (Alternate display by 3 digits)When the [Interrupt] key is 
pressed, the machine goes into the sub code input standby mode. When the [CA] key is pressed, the 
simulation is terminated.

21

Scanner counter display

The scanner counter value is displayed.  (Alternate display by 3 digits)When the [Interrupt] key is 
pressed, the machine goes into the sub code input standby mode. When the [CA] key is pressed, the 
simulation is terminated.

Main 
code

Sub 

code

Contents

Details of operation

•Small size is Letter R (A4R) or smaller.

Display lamp

Output mode

AE mode lamp
AE mode lamp & PHOTO mode lamp
AE & TEXT & PHOTO mode lamp 

Normal size width: Front surface
Small size width: Front surface
Manual paper feed mode

Display lamp (AB series)

Display lamp (Inch series)

Displayed version

141%

141%

Machine program

[07]SIMULATIONS.fm  3 ページ  ２００３年１２月１９日　金曜日　午後３時２６分