Sharp AR-5316E (serv.man3) Service Manual ▷ View online
AR-5316/5320 SIMULATIONS 7-5
51
02
Resist amount adjustment
Used to adjust the contact pressure of the machine resist roller and the RSPF resist roller onto the
paper.
(Operating procedure)
When this simulation is executed, the current set value is displayed.
When the exposure mode key is pressed, the following set items are changed sequentially. Enter an
adjustment value with the 10-key and press the [START] key, and the entered value will be saved and
a copy will be made. (Adjustment range: 1 ~ 99, Default: 50)
When the [CA] key is pressed, the entered value is saved and the simulation is terminated.
paper.
(Operating procedure)
When this simulation is executed, the current set value is displayed.
When the exposure mode key is pressed, the following set items are changed sequentially. Enter an
adjustment value with the 10-key and press the [START] key, and the entered value will be saved and
a copy will be made. (Adjustment range: 1 ~ 99, Default: 50)
When the [CA] key is pressed, the entered value is saved and the simulation is terminated.
Supported for the installed models only. Skipped for the models without installation.
53
10
SPF scan position change-over
setting
setting
Used to change over the scan position depending on that the SPF unit and the SPF document glass
holder section are of anti-dirt glass or not.
When this simulation is executed, the currently set code number is displayed.
Enter the code number corresponding to the SPF unit to be used and press [START] key, and the
setting will be changed over.
holder section are of anti-dirt glass or not.
When this simulation is executed, the currently set code number is displayed.
Enter the code number corresponding to the SPF unit to be used and press [START] key, and the
setting will be changed over.
Though this setting is changed, the other set values are not affected. (The other set values remain
unchanged.)
When replacing and installing the SPF unit, it is recommendable to use this simulation to set the
scan position and execute the scan position automatic adjustment.
unchanged.)
When replacing and installing the SPF unit, it is recommendable to use this simulation to set the
scan position and execute the scan position automatic adjustment.
64
01
Self print
The optical system status is ignored and a self print is made. Also when a print command is sent
from the host, printing is performed.
from the host, printing is performed.
(Operating procedure)
When this simulation is executed, warm-up is performed and the ready lamp is lighted.
(However, the scanner is invalid and no initial operation is made.)
Enter the code number with the 10-key, and select a cassette with the cassette select key and press
the [START] key. The selected cassette start paper feed and printing is performed in the selected
pattern.
(However, the scanner is invalid and no initial operation is made.)
Enter the code number with the 10-key, and select a cassette with the cassette select key and press
the [START] key. The selected cassette start paper feed and printing is performed in the selected
pattern.
*
Only the tray lamp and the online lamp are lighted, and no other lamps are lighted.
Printing is made in 1 by 2 mode, where one line is printed and the following two liens are not printed,
or in the grid pattern.
or in the grid pattern.
*
Input disable for 4 ~ 99
*
Print data are made on A3 size. (A3 paper is preferable.)
Main
code
code
Sub
code
Contents
Details of operation
Lighting lamp
Adjustment mode
AE, Main cassette lamp
AE, 2nd cassette lamp
AE, Manual paper feed lamp
AE, TEXT, PHOTO lamps
AE, 2nd cassette lamp
AE, Manual paper feed lamp
AE, TEXT, PHOTO lamps
Main cassette paper feed
2nd cassette paper feed
Manual paper feed
SPF document feed (Front surface)
Code No.
Mode
0
Set to the scan position of the current mass production SPF unit. (Default)
1
Set to the scan position of the ant-dirt SPF unit.
Code number
Pattern
0
1
2
3
1
2
3
1 by 2
Grid pattern
White paper
Black background
Grid pattern
White paper
Black background
[07]SIMULATIONS.fm 5 ページ 2003年12月19日 金曜日 午後3時26分
AR-5316/5320 USER PROGRAMS 8-1
[8] USER PROGRAMS
The user programs allow the parameters of certain functions to be set, changed, or canceled as desired.
1. List of user programs
This copier has the following user programs.
*1 On models with a SPF.
*2 On model with the two trays.
Program name
Program
No
Description
Default
Parameters
Auto clear time
1
"Auto clear time" automatically returns the copy settings to the initial
settings when a certain period of time elapses after a copy is made.
This program is used to select the period of time. "Auto clear time"
can also be disabled.
settings when a certain period of time elapses after a copy is made.
This program is used to select the period of time. "Auto clear time"
can also be disabled.
60sec
1 (OFF)
2 (10sec)
3 (20sec)
4 (60sec)
5 (90sec)
6 (120sec)
Preheat mode
2
This function automatically switches the machine to a low power
consumption state if the set duration of time elapses without the
machine being used when the power is on.
The POWER SAVE indicator lights up, however, the keys on the
operation panel can be used. Normal operation automatically
resumes when a key on the operation panel is pressed, a print job is
received or an original is placed.
consumption state if the set duration of time elapses without the
machine being used when the power is on.
The POWER SAVE indicator lights up, however, the keys on the
operation panel can be used. Normal operation automatically
resumes when a key on the operation panel is pressed, a print job is
received or an original is placed.
1min
1 (1min)
2 (5min)
3 (30min)
4 (60min)
5 (120min)
6 (240min)
Auto power shut-off timer
3
This function automatically switches the machine to a state that
consumes even less power than preheat mode if the set duration of
time elapses without the machine being used when the power is on.
All lights except the POWER SAVE indicator and ON LINE indicator
go off. To resume normal operation, press the [START] key. Normal
operation also resumes automatically when a print job is received or
scanning is begun from a computer. While in auto power shut-off
mode, no keys (except the [START] key) can be used.
consumes even less power than preheat mode if the set duration of
time elapses without the machine being used when the power is on.
All lights except the POWER SAVE indicator and ON LINE indicator
go off. To resume normal operation, press the [START] key. Normal
operation also resumes automatically when a print job is received or
scanning is begun from a computer. While in auto power shut-off
mode, no keys (except the [START] key) can be used.
5min
1 (5min)
2 (30min)
3 (60min)
4 (120min)
5 (240min)
Stream feeding mode *
1
4
When copying using the SPF, during the period of time that the SPF
indicator blinks after an original has been scanned (about 5
seconds), a subsequent original can be placed and automatically
fed into the machine.
indicator blinks after an original has been scanned (about 5
seconds), a subsequent original can be placed and automatically
fed into the machine.
OFF
0 (OFF)
1 (ON)
Auto power shut-off
setting
setting
5
Use this setting to enable or disable auto power shut-off.
ON
0 (OFF)
1 (ON)
Auto paper select mode *
2
8
This function automatically selects paper that is the same size as
the original placed in the SPF, or the same size as that selected with
the [ORIGINAL SIZE ENTER] key. The function can be disabled.
the original placed in the SPF, or the same size as that selected with
the [ORIGINAL SIZE ENTER] key. The function can be disabled.
ON
0 (OFF)
1 (ON)
Auto tray switching *
2
9
If the paper runs out during printing and there is paper of the same
size and orientation in another tray, this function automatically
switches to that tray (excluding the bypass tray). The function can be
disabled.
size and orientation in another tray, this function automatically
switches to that tray (excluding the bypass tray). The function can be
disabled.
ON
0 (OFF)
1 (ON)
Auditing mode
10
Use to enable or disable "Auditing mode".
"Auditing mode" is initially disabled.
"Auditing mode" is initially disabled.
OFF
0 (OFF)
1 (ON)
Account number entry
11
Use to set up account numbers.
Up to 20 accounts can be established.
Up to 20 accounts can be established.
-
-
Account number change
12
Use to change an account number.
-
-
Account number deletion
13
Use to delete an account number.
A single account number can be deleted, or all account numbers at
once.
A single account number can be deleted, or all account numbers at
once.
Delete
single
account
0 (Delete single account)
1 (Delete all accounts)
Number of copies per
account
account
14
This displays the number of copies made by each account.
The maximum count is 49,999. If this number is exceeded, the count
will start over from 0.
The maximum count is 49,999. If this number is exceeded, the count
will start over from 0.
-
-
Resetting account
15
Use to reset the copy count of an account to 0.
The copy count of a single account or of all accounts can be reset.
The copy count of a single account or of all accounts can be reset.
Reset single
account
0 (Reset single account)
1 (Reset all accounts)
Resolution in Auto/Text
mode
mode
23
This setting is used to change the copy resolution in AUTO and
TEXT mode from 600 x 300 dpi to 600 x 600 dpi
(high-quality mode).
Scanning is slower when high-quality mode is used.
TEXT mode from 600 x 300 dpi to 600 x 600 dpi
(high-quality mode).
Scanning is slower when high-quality mode is used.
300dpi
1 (300dpi)
2 (600dpi)
[08]USERPROGRAMS.fm 1 ページ 2003年12月19日 金曜日 午後3時27分
AR-5316/5320 USER PROGRAMS 8-2
Program name
Program
No
Description
Default
Parameters
Key auto repeat
25
Use this setting to select whether or not holding down a key causes
repeated input of the key. For keys that normally cause a set value to
increase when held down (for example, holding down the [ZOOM]
key), this program can be used to have the set value not change
when the key is held down.
repeated input of the key. For keys that normally cause a set value to
increase when held down (for example, holding down the [ZOOM]
key), this program can be used to have the set value not change
when the key is held down.
ON
0 (OFF)
1 (ON)
Key press time
26
Use this setting to select how long a key must be pressed for the
input to be accepted. By selecting a longer time, you can prevent
settings from being changed by the accidental pressing of a key.
input to be accepted. By selecting a longer time, you can prevent
settings from being changed by the accidental pressing of a key.
Minimum
(current
response
speed)
1 (Minimum
(current response speed))
(current response speed))
2 (0.5sec)
3 (1.0sec)
4 (1.5sec)
5 (2.0sec)
Audible signals volume
27
This sets the volume of beep signals.
short beep
1 (short beep)
2 (long beep)
3 (OFF)
Base setting beep signal
28
Use this to sound a beep when a base setting is selected.
OFF
0 (OFF)
1 (ON)
Number of copies limit
29
Use this setting to select 99 or 999 for the maximum number of
copies.
copies.
999 copies
1 (99 copies)
2 (999 copies)
Use close paper size
30
When this function is enabled, printing in printer mode will
automatically continue using a different size of paper if the specified
size of paper runs out in all trays. This feature does not function in
copy mode.
automatically continue using a different size of paper if the specified
size of paper runs out in all trays. This feature does not function in
copy mode.
OFF
0 (OFF)
1 (ON)
Default tray setting
31
Use this program to select a default tray. This tray is automatically
selected each time the power is turned on or each time the machine
reverts to the initial settings.
selected each time the power is turned on or each time the machine
reverts to the initial settings.
Upper
paper tray
1 (Upper paper tray)
2 (Lower paper tray)
5 (Bypass tray)
Default exposure mode
32
Use this program to set "AUTO", "TEXT", or "PHOTO" as the default
exposure mode.
exposure mode.
AUTO
1 (AUTO)
2 (TEXT)
3 (PHOTO)
[08]USERPROGRAMS.fm 2 ページ 2003年12月19日 金曜日 午後3時27分
AR-5316/5320 MAINTENANCE 10-1
[10] MAINTENANCE
1. Maintenance table
X:Check(Clean, adjust, or replace when required.) O:Clean
:Replace
:Adjust
:Lubricate
*1:Recommendable replacement time:50K(Letter,5%print)
Unit name
Part name
When calling
50K
100K
150K
Drum peripheral
OPC drum
-
Cleaning blade
-
Side seal F/R
X
X
X
X
MC unit
X
(MC charging electrode)
-
(
)
(
)
(
)
(MC grid)
-
(
)
(
)
(
)
(MC case)
-
(
)
(
)
(
)
Transfer wire
O
O
O
O
Transfer paper guide
O
O
O
O
MC guide sheet (Cleaning blade attached)
-
Drum fixing plate B
X
Process frame unit
X
X
X
Discharge holder
O
O
O
O
Separation pawl
Star ring x 2 pcs
X
Developing section
Developer
-
DV seal
-
X
X
DV under seal
-
-
-
DV side seal
-
X
X
Side Mylar
-
-
-
Optical section
Lamp unit
Reflector
O
O
O
O
Mirror
O
O
O
O
No.2/3 mirror unit
Mirror
O
O
O
O
Pulley
X
X
X
X
CCD peripheral
Lens
O
O
O
O
Glass
Table glass
O
O
O
O
White Plate
O
O
O
O
Other
Drive wire
X
X
X
X
Rail
X
X
X
X
Document cover
O
O
O
O
Document size sensor
O
O
O
O
LSU
Dust-proof glass
O
O
O
O
Paper feed section
Multi paper feed section
Take-up roller(manual / SPF)
O
O
O
O
Paper feed roller
O
O
O
O
Spring clutch
O
O
O
O
Paper transport section
PS roller
O
O
O
O
Transport (paper exit) rollers
O
O
O
O
Spring clutch
O
O
O
O
Fusing section
Upper heat roller
O
O
O
Pressure roller
O
O
O
O
Pressure roller bearing
X
X
X
O
Upper separation pawl
X
X
X
O
Lower separation pawl
X
X
X
O
Cleaning pad
X
X
X
Drive section
Gears
X
X
X
X
Belts
X
X
X
O
Paper exit section
Ozone filter*1
X
X
X
X
Only for Viet Nam
[10]MAINTENANCE.fm 1 ページ 2004年1月19日 月曜日 午後1時52分
Click on the first or last page to see other AR-5316E (serv.man3) service manuals if exist.