DOWNLOAD Sharp AR-505 (serv.man11) Service Manual ↓ Size: 136.57 KB | Pages: 11 in PDF or view online for FREE

Model
AR-505 (serv.man11)
Pages
11
Size
136.57 KB
Type
PDF
Document
Service Manual
Brand
Device
Copying Equipment / AR505 Service Manual-Trouble Code List
File
ar-505-sm11.pdf
Date
PREV: Sharp AR-505 (serv.man10) Service Manual

Sharp AR-505 (serv.man11) Service Manual ▷ View online

Trouble code
Description
Main
code
Sub
code
U9
00
Content Operation control communication trouble
(ICU detection)
Detail
Communication setup error,
framing/parity/protocol error
Cause
Slave unit PWB connector improper
connection
Slave unit PWB – ICU PWB harness
trouble
Connector pin breakage of the motor
PWB of the slave unit PWB
Slave unit ROM trouble. no ROM, ROM
reverse insertion, ROM pin breakage
Check
and
remedy
Connect the connector of the slave unit
PWB and the ICU PWB.
Check the connection and the harness.
Check the grounding of the copier.
Check the ROM of the slave unit PWB.
90
Content Operation control communication trouble
(OPE detection)
Detail
Communication setup
error/framing/parity/protocol error
Cause
Slave unit PWB connector improper
connection
Slave unit PWB – ICU PWB harness
trouble
Slave unit PWB mother board connector
pin breakage
Check
and
remedy
Check the slave unit PWB and the ICU
PWB connector connection.
Check the copier earth.
EE
EL
Content Auto developing adjustment trouble
(overtoner)
Detail
A sample data is less than 0 when auto
developing adjustment is executed.
Cause
Toner density sensor defective
Charging voltage or developing voltage
improper.
Toner density improper
Developing unit defective
PCU PWB defective
Check
and
remedy
Make auto developing adjustment with
SIM25-2.
EU
Content Auto developing adjustment trouble
(undertoner)
Detail
A sample data is less than 99 when auto
developing adjustment is executed.
Cause
Toner density sensor defective
Charging voltage or developing voltage
improper
Toner density improper
Unit defective
PCU PWB defective
Check
and
remedy
Make auto developing adjustment with
SIM25-2.
Trouble code
Description
Main
code
Sub
code
FC
00
Content ASK/IrDA modulation LSI reset error
Detail
Though the RESET signal pulse is sent
to the ASK/IrDA modulation LSI, the
power signal is not turned ON.
Cause
1)  ICU main PWB defect
2) ASK/IrDA modulation LSI/Clock
oscillator defect
Check
and
remedy
Perform the self diag with SIM 68-01.
Replace the ICU main PWB.
01
Content ASK/IrDA switch error
Detail
Though the ASK/IrDA switch command is
sent to the ASK/IrDA modulation LSI, the
AI signal is not changed.
Cause
1)  ICU main PWB defect
2) ASK/IrDA modulation LSI/Clock
oscillator defect
Check
and
remedy
Perform the self diag with SIM 68-01.
Replace the ICU main PWB.
PF
00
Content RIC copy inhibition command reception
Detail
Copy inhibition command received from
RIC (host)
Cause
Judged by the host.
Check
and
remedy
Notice to the host
––
Content Auditor not ready
AR-505
9 – 10
8/6/1999
Trouble code
Description
Main
code
Sub
code
U9
00
Content Operation control communication trouble
(ICU detection)
Detail
Communication setup error,
framing/parity/protocol error
Cause
Slave unit PWB connector improper
connection
Slave unit PWB – ICU PWB harness
trouble
Connector pin breakage of the motor
PWB of the slave unit PWB
Slave unit ROM trouble. no ROM, ROM
reverse insertion, ROM pin breakage
Check
and
remedy
Connect the connector of the slave unit
PWB and the ICU PWB.
Check the connection and the harness.
Check the grounding of the copier.
Check the ROM of the slave unit PWB.
90
Content Operation control communication trouble
(OPE detection)
Detail
Communication setup
error/framing/parity/protocol error
Cause
Slave unit PWB connector improper
connection
Slave unit PWB – ICU PWB harness
trouble
Slave unit PWB mother board connector
pin breakage
Check
and
remedy
Check the slave unit PWB and the ICU
PWB connector connection.
Check the copier earth.
EE
EL
Content Auto developing adjustment trouble
(overtoner)
Detail
A sample data is less than 0 when auto
developing adjustment is executed.
Cause
Toner density sensor defective
Charging voltage or developing voltage
improper.
Toner density improper
Developing unit defective
PCU PWB defective
Check
and
remedy
Make auto developing adjustment with
SIM25-2.
EU
Content Auto developing adjustment trouble
(undertoner)
Detail
A sample data is less than 99 when auto
developing adjustment is executed.
Cause
Toner density sensor defective
Charging voltage or developing voltage
improper
Toner density improper
Unit defective
PCU PWB defective
Check
and
remedy
Make auto developing adjustment with
SIM25-2.
Trouble code
Description
Main
code
Sub
code
FC
00
Content ASK/IrDA modulation LSI reset error
Detail
Though the RESET signal pulse is sent
to the ASK/IrDA modulation LSI, the
power signal is not turned ON.
Cause
1)  ICU main PWB defect
2) ASK/IrDA modulation LSI/Clock
oscillator defect
Check
and
remedy
Perform the self diag with SIM 68-01.
Replace the ICU main PWB.
01
Content ASK/IrDA switch error
Detail
Though the ASK/IrDA switch command is
sent to the ASK/IrDA modulation LSI, the
AI signal is not changed.
Cause
1)  ICU main PWB defect
2) ASK/IrDA modulation LSI/Clock
oscillator defect
Check
and
remedy
Perform the self diag with SIM 68-01.
Replace the ICU main PWB.
PF
00
Content RIC copy inhibition command reception
Detail
Copy inhibition command received from
RIC (host)
Cause
Judged by the host.
Check
and
remedy
Notice to the host
––
Content Auditor not ready
AR-505
9 – 10
8/6/1999
Trouble code
Description
Main
code
Sub
code
U9
00
Content Operation control communication trouble
(ICU detection)
Detail
Communication setup error,
framing/parity/protocol error
Cause
Slave unit PWB connector improper
connection
Slave unit PWB – ICU PWB harness
trouble
Connector pin breakage of the motor
PWB of the slave unit PWB
Slave unit ROM trouble. no ROM, ROM
reverse insertion, ROM pin breakage
Check
and
remedy
Connect the connector of the slave unit
PWB and the ICU PWB.
Check the connection and the harness.
Check the grounding of the copier.
Check the ROM of the slave unit PWB.
90
Content Operation control communication trouble
(OPE detection)
Detail
Communication setup
error/framing/parity/protocol error
Cause
Slave unit PWB connector improper
connection
Slave unit PWB – ICU PWB harness
trouble
Slave unit PWB mother board connector
pin breakage
Check
and
remedy
Check the slave unit PWB and the ICU
PWB connector connection.
Check the copier earth.
EE
EL
Content Auto developing adjustment trouble
(overtoner)
Detail
A sample data is less than 0 when auto
developing adjustment is executed.
Cause
Toner density sensor defective
Charging voltage or developing voltage
improper.
Toner density improper
Developing unit defective
PCU PWB defective
Check
and
remedy
Make auto developing adjustment with
SIM25-2.
EU
Content Auto developing adjustment trouble
(undertoner)
Detail
A sample data is less than 99 when auto
developing adjustment is executed.
Cause
Toner density sensor defective
Charging voltage or developing voltage
improper
Toner density improper
Unit defective
PCU PWB defective
Check
and
remedy
Make auto developing adjustment with
SIM25-2.
Trouble code
Description
Main
code
Sub
code
FC
00
Content ASK/IrDA modulation LSI reset error
Detail
Though the RESET signal pulse is sent
to the ASK/IrDA modulation LSI, the
power signal is not turned ON.
Cause
1)  ICU main PWB defect
2) ASK/IrDA modulation LSI/Clock
oscillator defect
Check
and
remedy
Perform the self diag with SIM 68-01.
Replace the ICU main PWB.
01
Content ASK/IrDA switch error
Detail
Though the ASK/IrDA switch command is
sent to the ASK/IrDA modulation LSI, the
AI signal is not changed.
Cause
1)  ICU main PWB defect
2) ASK/IrDA modulation LSI/Clock
oscillator defect
Check
and
remedy
Perform the self diag with SIM 68-01.
Replace the ICU main PWB.
PF
00
Content RIC copy inhibition command reception
Detail
Copy inhibition command received from
RIC (host)
Cause
Judged by the host.
Check
and
remedy
Notice to the host
––
Content Auditor not ready
AR-505
9 – 10
8/6/1999
Trouble code
Description
Main
code
Sub
code
U9
00
Content Operation control communication trouble
(ICU detection)
Detail
Communication setup error,
framing/parity/protocol error
Cause
Slave unit PWB connector improper
connection
Slave unit PWB – ICU PWB harness
trouble
Connector pin breakage of the motor
PWB of the slave unit PWB
Slave unit ROM trouble. no ROM, ROM
reverse insertion, ROM pin breakage
Check
and
remedy
Connect the connector of the slave unit
PWB and the ICU PWB.
Check the connection and the harness.
Check the grounding of the copier.
Check the ROM of the slave unit PWB.
90
Content Operation control communication trouble
(OPE detection)
Detail
Communication setup
error/framing/parity/protocol error
Cause
Slave unit PWB connector improper
connection
Slave unit PWB – ICU PWB harness
trouble
Slave unit PWB mother board connector
pin breakage
Check
and
remedy
Check the slave unit PWB and the ICU
PWB connector connection.
Check the copier earth.
EE
EL
Content Auto developing adjustment trouble
(overtoner)
Detail
A sample data is less than 0 when auto
developing adjustment is executed.
Cause
Toner density sensor defective
Charging voltage or developing voltage
improper.
Toner density improper
Developing unit defective
PCU PWB defective
Check
and
remedy
Make auto developing adjustment with
SIM25-2.
EU
Content Auto developing adjustment trouble
(undertoner)
Detail
A sample data is less than 99 when auto
developing adjustment is executed.
Cause
Toner density sensor defective
Charging voltage or developing voltage
improper
Toner density improper
Unit defective
PCU PWB defective
Check
and
remedy
Make auto developing adjustment with
SIM25-2.
Trouble code
Description
Main
code
Sub
code
FC
00
Content ASK/IrDA modulation LSI reset error
Detail
Though the RESET signal pulse is sent
to the ASK/IrDA modulation LSI, the
power signal is not turned ON.
Cause
1)  ICU main PWB defect
2) ASK/IrDA modulation LSI/Clock
oscillator defect
Check
and
remedy
Perform the self diag with SIM 68-01.
Replace the ICU main PWB.
01
Content ASK/IrDA switch error
Detail
Though the ASK/IrDA switch command is
sent to the ASK/IrDA modulation LSI, the
AI signal is not changed.
Cause
1)  ICU main PWB defect
2) ASK/IrDA modulation LSI/Clock
oscillator defect
Check
and
remedy
Perform the self diag with SIM 68-01.
Replace the ICU main PWB.
PF
00
Content RIC copy inhibition command reception
Detail
Copy inhibition command received from
RIC (host)
Cause
Judged by the host.
Check
and
remedy
Notice to the host
––
Content Auditor not ready
AR-505
9 – 10
8/6/1999
Page of 11
Display

Sharp AR-505 (serv.man11) Service Manual ▷ Download

Found More:

AR-505 (serv.man11) Service Manuals

Preview DownloadPagesSize
AR-505 (serv.man3) AR505 Service Manual-Circuit Diagrams Service Manual 48 2.21 MB
AR-505 (serv.man4) AR505 Service Manual-General Specifications Service Manual 16 556.42 KB
AR-505 (serv.man5) AR505 Service Manual-Consumable Parts Service Manual 11 160.81 KB
AR-505 (serv.man6) AR505 Service Manual-Installation Setup Service Manual 10 655.42 KB
AR-505 (serv.man7) AR505 Service Manual-External View Internal Structure Service Manual 11 835.78 KB
AR-505 (serv.man8) AR505 Service Manual-Setting Adjustments Service Manual 32 1.82 MB
AR-505 (serv.man9) AR505 Service Manual-Simulation Service Manual 51 1.06 MB
AR-505 (serv.man10) AR505 Service Manual-Disassemby, Assembly Maintenance Service Manual 29 3.94 MB
AR-505 (serv.man12) AR505 Service Manual-Operational Description Service Manual 11 351.69 KB
AR-505 (serv.man15) AR505 Operation Manual User Manual / Operation Manual 127 3.39 MB
AR-505 (serv.man13) Parts Guide AR250 280 285 287 335 337 405 407 505 507 Service Manual / Parts Guide 127 5.15 MB
AR-505 (serv.man14) AR505 Parts Guide Service Manual / Parts Guide 127 6.67 MB
AR-505 (serv.man2) AR505 Specifications Service Manual / Specification 6 79.24 KB
AR-505 (serv.man23) Change of Fuser Cover Part Number. Service Manual / Technical Bulletin 1 25.47 KB
AR-505 (serv.man24) Improvement made to prevent fire hazard caused by imperfect contact on fixing junction PWB. Service Manual / Technical Bulletin 1 45.23 KB
AR-505 (serv.man25) Re issue bulletin regarding a parts change - mainly for the mirror mount fixing plate. Service Manual / Technical Bulletin 4 1.6 MB
AR-505 (serv.man26) Change to the paper feed roller material. Service Manual / Technical Bulletin 13 1.22 MB
AR-505 (serv.man27) Reduction of F2-00 error. (Toner supply error) Service Manual / Technical Bulletin 2 12.33 KB
AR-505 (serv.man28) New service part for repairing a broken ADU frame Service Manual / Technical Bulletin 2 239.04 KB
AR-505 (serv.man29) Parts change information Service Manual / Technical Bulletin 2 45.08 KB
AR-505 (serv.man30) Paper feed drive unit part change Service Manual / Technical Bulletin 1 30.01 KB
AR-505 (serv.man31) Corrections carried out in the parts guide (DV unit toner hopper) Service Manual / Technical Bulletin 2 91.77 KB
AR-505 (serv.man32) HV protect sheet addition Service Manual / Technical Bulletin 1 36.2 KB
AR-505 (serv.man33) Corrections made to a jamming error caused by the ADU transfer clutch dragging or slipping Service Manual / Technical Bulletin 1 42.95 KB
AR-505 (serv.man34) RSPF parts change information Service Manual / Technical Bulletin 1 31.68 KB
AR-505 (serv.man35) Part change information Service Manual / Technical Bulletin 3 88.01 KB
AR-505 (serv.man36) Establishment of the paper feeding drive clutch with mylar sheet attached as a service part Service Manual / Technical Bulletin 1 30.63 KB
AR-505 (serv.man37) Parts change information Service Manual / Technical Bulletin 1 30.59 KB
AR-505 (serv.man38) Supply of silicon oil used for cleaning the SPF glass to be carried out as a service part Service Manual / Technical Bulletin 1 30.82 KB
AR-505 (serv.man39) Copy paper jams caused by grease entering the internal section of the paper feeding drive clutch and supply of Hanari grease as a service part Service Manual / Technical Bulletin 1 34.59 KB
AR-505 (serv.man40) Corrections carried out in the parts guide Service Manual / Technical Bulletin 1 30.08 KB
AR-505 (serv.man41) Change carried out in the material of the reversion gate Service Manual / Technical Bulletin 1 29.82 KB
AR-505 (serv.man42) Establishment of the CG reverse roller shaft UN and the Reverse roller shaft UN in the 550 paper feeding unit as service parts Service Manual / Technical Bulletin 2 52.22 KB
AR-505 (serv.man43) Correction carried out in the parts guide for the charger wire Service Manual / Technical Bulletin 1 19.22 KB
AR-505 (serv.man44) Part changes Service Manual / Technical Bulletin 1 33.26 KB
AR-505 (serv.man45) Notice of jam cause codes Service Manual / Technical Bulletin 3 153.47 KB
AR-505 (serv.man46) Parts change information (intake air duct 1, intake air filter, screws, IC) Service Manual / Technical Bulletin 1 30.57 KB
AR-505 (serv.man47) Using the same hand-feed pick-up roller as the 550 paper-feeding unit Service Manual / Technical Bulletin 1 29.8 KB
AR-505 (serv.man48) Improvement in strength of the RSPF hinge Service Manual / Technical Bulletin 1 38.66 KB
AR-505 (serv.man49) Parts change information (PCU flash PWB, PBA control PWB, paper feeding unit) Service Manual / Technical Bulletin 1 31.62 KB
AR-505 (serv.man50) Polygon motors for laser units. Service Manual / Technical Bulletin 1 20.69 KB
AR-505 (serv.man51) Problem code L4-03 (fusing motor lock detection) notification. Service Manual / Technical Bulletin 1 65.15 KB
AR-505 (serv.man52) EPROM upgrade for RSPF. Service Manual / Technical Bulletin 1 74.13 KB
AR-505 (serv.man53) Added upper cover cushion for RSPF unit. Service Manual / Technical Bulletin 1 108.7 KB
AR-505 (serv.man54) Skew margin up of RSPF reverse unit. Service Manual / Technical Bulletin 2 106.51 KB
AR-505 (serv.man55) Change to pulley fixing double-thread screw and discontinued M4 tap. Service Manual / Technical Bulletin 1 86.27 KB
AR-505 (serv.man56) Change to the metal plating of the ADU connecting shaft and addition of a distinguishing groove. Service Manual / Technical Bulletin 1 128.54 KB
AR-505 (serv.man57) Change carried out in the hopper seal of the developing tank. Service Manual / Technical Bulletin 6 213.68 KB
AR-505 (serv.man58) Change of parts used in 550 paper feeding unit. Service Manual / Technical Bulletin 2 123.7 KB
AR-505 (serv.man59) Problem with main drive unit paper feed clutch. Service Manual / Technical Bulletin 2 77.29 KB
AR-505 (serv.man60) Addition of explanatory label for lever operation and change of suction lift shaft. Service Manual / Technical Bulletin 1 120.53 KB
AR-505 (serv.man61) ICU PWB part number change. Service Manual / Technical Bulletin 1 74.42 KB
AR-505 (serv.man62) Action to alleviate problems of static electricity through the use of a plastic bag for the machine. Service Manual / Technical Bulletin 1 72.61 KB
AR-505 (serv.man63) Corrections to technical bulletin ref. 032 Service Manual / Technical Bulletin 1 84.47 KB
AR-505 (serv.man64) Abnormal noise from process unit. Service Manual / Technical Bulletin 1 60.17 KB
AR-505 (serv.man65) Service guide to overcome exit unit paper jams. Service Manual / Technical Bulletin 3 104.29 KB
AR-505 (serv.man66) Part change information. Service Manual / Technical Bulletin 2 159.77 KB
AR-505 (serv.man67) Change of supplier for sintered bearings. (WHITE) Service Manual / Technical Bulletin 4 188.8 KB
AR-505 (serv.man68) Changes to the AR505 Service Manual and addition of jam cause codes. (WHITE) Service Manual / Technical Bulletin 5 323.33 KB
AR-505 (serv.man69) Change carried out in the original document detection photo sensor. (WHITE) Service Manual / Technical Bulletin 1 73.94 KB
AR-505 (serv.man70) Change carried out in the paper feeding drive frame and the transport clutch. (WHITE) Service Manual / Technical Bulletin 2 119.13 KB
AR-505 (serv.man71) Change carried out in the PS front roller bearing. (WHITE) Service Manual / Technical Bulletin 1 83.23 KB
AR-505 (serv.man72) Change carried out in the waste toner drive gear in the main drive unit. (WHITE) Service Manual / Technical Bulletin 1 83.13 KB
AR-505 (serv.man73) Measure to alleviate problems of snagging the copy keys on the operation panel. (YELLOW) Service Manual / Technical Bulletin 1 60.78 KB
AR-505 (serv.man74) Action to alleviate problems of dislocation of the disjunction arm in the ADU unit. (WHITE) Service Manual / Technical Bulletin 1 83.86 KB
AR-505 (serv.man75) Change carried out in the maker of the CCD manufactured PWB. (WHITE) Service Manual / Technical Bulletin 1 91.89 KB
AR-505 (serv.man76) Change carried out in the shape of the locking PAWL of the toner hopper. (WHITE) Service Manual / Technical Bulletin 1 85.55 KB
AR-505 (serv.man77) Change carried out in the location of production of the LSU unit. (WHITE) Service Manual / Technical Bulletin 1 88.23 KB
AR-505 (serv.man78) Correction of CG50 curvature in the turnover paper guide. (YELLOW) Service Manual / Technical Bulletin 2 98.03 KB
AR-505 (serv.man79) Discontinuance of the adjustment plate in the CCD unit. (WHITE) Service Manual / Technical Bulletin 1 133.79 KB
AR-505 (serv.man80) No bulletin. Service Manual / Technical Bulletin 2 96.34 KB
AR-505 (serv.man81) Countermeasure against Z-folding and paper mis-feed. (WHITE) Service Manual / Technical Bulletin 4 552.17 KB
AR-505 (serv.man82) Measure to improve the performance of the copy lamp. (WHITE) Service Manual / Technical Bulletin 1 114.6 KB
AR-505 (serv.man83) Addition of a binding band carried out to the LSU harness. (WHITE) Service Manual / Technical Bulletin 1 94.1 KB
AR-505 (serv.man84) Change carried out in the shape of the bushing and the attachment gear in the paper-feeding drive unit. (WHITE) Service Manual / Technical Bulletin 2 137.66 KB
AR-505 (serv.man85) Change in shape of the TC holder R. (WHITE) Service Manual / Technical Bulletin 1 121.04 KB
AR-505 (serv.man86) Discontinuance of the adjustment plate in the CCD unit. (WHITE) Service Manual / Technical Bulletin 1 139.63 KB
AR-505 (serv.man87) Report of flash memory version method. (WHITE) Service Manual / Technical Bulletin 3 130.14 KB
AR-505 (serv.man88) Marks on the rear frame of copier, ghosting on the rear frame of copies. (WHITE) Service Manual / Technical Bulletin 1 89.71 KB
AR-505 (serv.man89) Fixing ARPB2 F9 00 error messages. (WHITE) Service Manual / Technical Bulletin 2 96.34 KB
AR-505 (serv.man90) Corrections to the Service Manual. (WHITE) Service Manual / Technical Bulletin 3 181.37 KB
AR-505 (serv.man91) 1.Change to the F spacer rubber. 2.Discontinuance of the RSPF smap band. 3.Shape change of the attachment section of the RSPF paper delivery flapper Mylar sheet. 4.Change of position of the RSPF harness connector. 5.Shape change of the RSPF EMP lever. 6.Change to the motor of the RSPF motor. 7.Shape change of the RSPF bushing. (WHITE) Service Manual / Technical Bulletin 4 192.53 KB
AR-505 (serv.man92) 1.Measure carried out to improve the image quality (image misalignment) of the size guide. 2.Change carried out in the software for the printer driver and in the operator's manual. (WHITE) Service Manual / Technical Bulletin 2 139.22 KB
AR-505 (serv.man93) 1.Improvement of picture quality (edge zipzag) by changing RSPF W guide. 2.Addition of positioning on RSPF delivery guide. 3.Change of RSPF kam cover handle. 4.Set up unit parts for RSPF service. (WHITE) Service Manual / Technical Bulletin 3 151.97 KB
AR-505 (serv.man94) 1.Change carried out in the stir plate of the developing tank unit. 2.Change carried out in the material used for the TX sheet in the toner hopper unit. (WHITE) Service Manual / Technical Bulletin 3 156.32 KB
AR-505 (serv.man95) Change in parts carried out in the RSPF. (WHITE) Service Manual / Technical Bulletin 2 137.27 KB
AR-505 (serv.man96) Change Of Parts To Diminish The Noise From The Polygon Motor. (WHITE) Service Manual / Technical Bulletin 1 38.82 KB
AR-505 (serv.man97) 1.Change Carried Out In The Plastic Slider Washer In The ADU Unit. 2.Action To Alleviate Problems Of Static Electricity In The OP Control PWB Unit. (WHITE) Service Manual / Technical Bulletin 2 157.99 KB
AR-505 (serv.man98) Report Of Flash Memory Version Method. (WHITE) Service Manual / Technical Bulletin 2 127.33 KB
AR-505 (serv.man99) 1.Change Carried Out In The Shape Of The RSPF R Side Plate Chaulking Assembly. 2.Action To Alleviate Problems Of RSPF Original Document Delivery Jams. 3.Action To Stabilize The RSPF Pulse Motor Tension. 4.Action To Improve Conditions Of Magnetic Noise In The RSPF Paper Feeding Section. (WHITE) Service Manual / Technical Bulletin 3 168.51 KB
AR-505 (serv.man100) 1.Correction Of Screws In The Scanner Unit. 2.Addition Carried Out Of A Harness Protect Sheet S. (WHITE) Service Manual / Technical Bulletin 2 160.89 KB
AR-505 (serv.man101) 1.Change Of The Parts Code Of The Assembly Of The RSPF EPROM And PWB. 2.Improvement Of The RSPF Harness Wiring. 3.Creation Of The Parts Codes Of The RSPF Packing Materials. (WHITE) Service Manual / Technical Bulletin 2 161.33 KB
AR-505 (serv.man102) New Establishment Of The Flash ROM. (WHITE) Service Manual / Technical Bulletin 1 118.24 KB
AR-505 (serv.man103) Original Jamming When Using RSPF. (WHITE) Service Manual / Technical Bulletin 2 105.44 KB
AR-505 (serv.man104) 1.Change Of The ICU PWB Unit At EFI's Request. 2.Change Of The Touch Panel Maker. 3.Change Of The Heat-resistant Clamp Fixing Screws In The Fusing Unit. 4.Change Of The Action Time Changing The ICU PWB Memory To SDRAM. (WHITE) Service Manual / Technical Bulletin 3 87.23 KB
AR-505 (serv.man105) 1.Change Of The Parts Code Of The Assembly Of The RSPF EPROM And PWB. 2.Improvement Of The RSPF Harness Wiring. 3.Creation Of The Parts Codes Of The RSPF Packing Materials. (WHITE) Service Manual / Technical Bulletin 2 88.26 KB
AR-505 (serv.man106) 1.Change Of The Installation Procedure Manual. 2.Correction Of The Omissions In The Parts Guide. (WHITE) Service Manual / Technical Bulletin 3 160.17 KB
AR-505 (serv.man107) Extension Of The Rib On The Rail Section Of The 550-Tray Case. (WHITE) Service Manual / Technical Bulletin 1 89.18 KB
AR-505 (serv.man108) Corrections Carried Out In The Parts Guide. (WHITE) Service Manual / Technical Bulletin 7 294.09 KB
AR-505 (serv.man109) 1.Increase Of The DC Power Supply Capacity. 2.Change Of The Memory On The ICU PWB To SDRAM. 3.Change Of The Installation Procedure Manual And Addition Of Wire Saddle. (WHITE) Service Manual / Technical Bulletin 2 109.26 KB
AR-505 (serv.man110) 1.Satisfaction Of The Argentine Safety Standard. 2.Increase Of Strength Of The Boss On The Right End Of The RSPF Base. 3.Removal Of The RSPF Upper Guide Plate Holes And Addition Of The Delivery Paper Guide Positioner. (WHITE) Service Manual / Technical Bulletin 2 100.29 KB
AR-505 (serv.man111) Addition Of The Original Description Label And Lever Operation Description Label. (WHITE) Service Manual / Technical Bulletin 2 119.28 KB
AR-505 (serv.man112) ROM Version Upgrade. (WHITE) Service Manual / Technical Bulletin 2 98.79 KB
AR-505 (serv.man113) Change Carried Out In The Hard Disk. (WHITE) Service Manual / Technical Bulletin 2 116.41 KB
AR-505 (serv.man114) 1.Change Carried Out In The Main Harness. 2.Change Carried Out In The Spring Of The Multi Manual Unit. (WHITE) Service Manual / Technical Bulletin 2 78.44 KB
AR-505 (serv.man115) New Parts Required For The Addition Of A Fan. (WHITE) Service Manual / Technical Bulletin 2 82.18 KB
AR-505 (serv.man116) 1.Measure To Alleviate Problems Of Folded Corners Of The Copy Paper In The Fusing Unit. 2.Measure To Improve The Paper Transport Performance Of The Original Document In The RSPF. 3.Measure To Tighten The Looseness Of The Table Glass. (WHITE) Service Manual / Technical Bulletin 2 85.89 KB
AR-505 (serv.man117) 1.Change Carried Out In The Bearings In The Paper Feeding Drive Unit. 2.Discontinuance Of The Manual Pressure Spring Attachment Plate. (WHITE) Service Manual / Technical Bulletin 2 79.01 KB
AR-505 (serv.man118) Addition Of Cleaning Operations During Maintenance Cycles For The Reversion Paper Guide And Paper Delivery Actuator. (WHITE) Service Manual / Technical Bulletin 2 92.75 KB
AR-505 (serv.man119) Corrections To The Service Manual. (WHITE) Service Manual / Technical Bulletin 4 169.99 KB
AR-505 (serv.man120) Change Carried Out In The Shape Of The AC Harness Cover. (WHITE) Service Manual / Technical Bulletin 2 76.14 KB
AR-505 (serv.man121) Report Of Flash Memory Version Method. (WHITE) Service Manual / Technical Bulletin 8 330.52 KB
AR-505 (serv.man122) Change Of Support Plates For Reverse Roller And Decurling Roller Support Plate Of ADU. (WHITE) Service Manual / Technical Bulletin 2 117.1 KB
AR-505 (serv.man18) ASPI Update and Check Utility Driver / Update 1.94 MB
AR-505 (serv.man19) Flash 5.1 Download Utility Driver / Update 16.94 KB
AR-505 (serv.man20) AR505 PCU Firmware 5.11 Driver / Update 822.71 KB
AR-505 (serv.man21) AR505 ICU Firmware 5.10 Driver / Update 1.02 MB
AR-505 (serv.man22) AR505 OPE Firmware 5.10 Driver / Update 1.27 MB
AR-505 Cougar Handy Guide (Updated March'02) Handy Guide 54 218.68 KB
AR-505 (serv.man16) Service Exchange Scheme Request Form (TP ServiceCo) FAQ 1 7.68 KB
AR-505 (serv.man17) Cougar Firmware Revision Table FAQ 6 19.71 KB
AR-505 (serv.man123) MSDS F-00951 Regulatory Data 2 12.98 KB
AR-505 (serv.man124) MSDS F-00941 Regulatory Data 2 12.48 KB
AR-505 (serv.man125) MSDS F-30951 Regulatory Data 2 11.96 KB
AR-505 (serv.man126) MSDS F-30941 Regulatory Data 2 11.67 KB
AR-505 (serv.man127) Environmental Data Sheet Regulatory Data 1 4.5 KB

RANDOM: