Sharp AR-405 (serv.man6) Service Manual ▷ View online
(9) Staple unit
Paper discharge tray
Lift tray
Storage
Face-up
Number of sheets
that can be stapled
that can be stapled
50 sheets (80 g/m
2
)
25 sheets when the size is over A4/LT.
Paper size
AB series
A3, B4, A4, A4R, B5
Inch series
11"
×
17"/8.5"
×
14"/
8.5"
×
13"/8.5"
×
11"/
8.5"
×
11"R
Stapling reference
1 point (front)/ 1 point (far end)/ 2 points
Needle feed system
Cartridge (5000 needles)
Detection
No needle/no cartridge/stapler rotation
Service life
more than 100 K
Manual mode
None
(10) Power supply
Supplied from copier (DC 24V, DC 5V)
(11) Power consumption
MAX 60W
(12) Dimensions
590 (W)
×
560 (D)
×
998 (H)
(13) Weight
About 50 kg
G. Finisher AR-FN2
(1) Type
Installation to copier body (Separate installation allowed)
(2) Tray section specifications
Upper tray
Lower tray
Tray type
Normal tray
Lift tray
Capacity
250 sheets (A4/Letter,
80g/m
80g/m
2
)
750 sheets
(A4/Letter, 80g/m
(A4/Letter, 80g/m
2
)
Storing system
Face up
Face up/Face
down
down
Paper exit size
A3
∼
A6R
11"
×
17"
∼
5 1/2"
×
8 1/2", 12"
×
18"
A4, B5
8 1/2"
8 1/2"
×
11"
Paper weight
52
∼
128g/m
2
, 176g/m
2
,
200g/m
2
(For 105g/m
2
or above, A4/Letter size
or smaller)
or smaller)
56
∼
128g/m
2
Paper full detection None
Yes
(3) Lift tray section
Offset amount
15mm, A4 35mm: B5 24mm: 8.5
×
11
(4) Staple section
Storing system
Face up
Stapling system
Flat clinch
Stapling capacity
30 sheets (80g/m
2
)
Applicable size
AB series: A4, B5
Inch series: 8 1/2
Inch series: 8 1/2
×
11
Alignment
Max. shift width: 1mm
Stapling reference
One position (front)
Staple supply system
Cartridge system (5000 pcs.)
Staple
Common with AR-SS1, SF-S54
Detection
Detection of no staple/no cartridge/no
stapler
stapler
(5) External dimensions
457mm (W)
×
518mm (D)
×
820mm (H)
552mm (W)
×
518mm (D)
×
866mm (H)(with the upper tray
extended)
(6) Weight
22Kg
(7) Power
Supplied from the copier body.
H. 3-tray finisher AR-FN1N
(1) Type
Type
Installed to the copier body. (Detachable)
Tray type
Top stage
Normal tray
Middle stage
Normal tray
Bottom stage
Lift-up tray
(2) Tray capacity
Capacity
Top stage
500 sheets
Middle stage
500 sheets
Bottom stage
1,500 sheets
A4/Letter size, 80g/m
2
(3) Paper transport/paper exit
Paper transport
Center reference
Paper exit system
Face up/Face down
Paper exit direction
Discharged from the left side of the
document.
document.
(4) Paper size
Paper
exit size
exit size
Top
stage
stage
Face up
A3
∼
A6R, 11
×
17
∼
5.5
×
8.5,
Special paper
Face down
A3
∼
B5, 11
×
17
∼
8.5
×
11R
Middle
stage
stage
Face up
A3
∼
A5, 11
×
17
∼
5.5
×
8.5
Face down
A3
∼
B5, 11
×
17
∼
8.5
×
11R
Bottom
stage
stage
Face up
A3
∼
B5R, 11
×
17
∼
8.5
×
11R
Face down
A3
∼
B5R, 11
×
17
∼
8.5
×
11R
Paper
weight
weight
Top
stage
stage
Face up
56
∼
128g/m
2
, 176g/m
2
,
200g/m
2
Face down
56
∼
105g/m
2
Middle
stage
stage
Face up
56
∼
105g/m
2
Face down
56
∼
105g/m
2
Bottom
stage
stage
Face up
56
∼
128g/m
2
, 176g/m
2
,
200g/m
2
Face down
56
∼
105g/m
2
For paper weight of greater than 105g/m
2
, A4/8.5
×
11 or less.
(5) Paper full detection
Paper full
detection
detection
Top stage
Full detection available
Middle
stage
stage
Full detection available
Bottom
stage
stage
5-step sensor with full detection
(0%
(0%
∼
, 25%
∼
, 50%
∼
, 75%
∼
,
100% (full))
AR-405
3 – 3
1/21/1999
(6) Offset
Tray available
Bottom tray
Offset amount
25mm
(7) Power source
Power source
Supplied from the copier (DC 24V/DC 25)
(8) Power consumption
Max. power consumption
About 60W
(9) External view
Dimensions
590 (W)
×
560 (D)
×
998 (H)
Box color
Frosty gray
Weight
About 45kg
(10) Staple functions
Stable available
Bottom stage tray only
Face up only
Stapling
capacity
capacity
50 sheets (60g/m
2
)
(25 sheets for sizes greater than A4/8.5
×
11)
Sizes available
for stapling
for stapling
AB series
A3, B4, A4, A4R, B5, B5R
Inch series
11
×
17, 8.5
×
14, 8.5
×
13, 8.5
×
11, 8.5
×
11R
Alignment
(when stapling)
(when stapling)
Max. shift: within 1mm
Stapling
reference
reference
One position (Left rear), One position (Left
front), 2 positions (left side)
front), 2 positions (left side)
Stapler supply
Cartridge (5,000 pcs.)
Stapler
SF-SC11 (The staple cartridge case is supplied
as a service part.)
as a service part.)
Detection
Staple empty detection, no cartridge detection
Manual staple
mode
mode
Not available
I. Dual tray output unit AR-TR1
(1) Capacity
No. of bins
2 trays
Capacity
Upper stage
250 sheets
Lower stage
100 sheets
(2) Paper transport/paper exit
Paper transport
Center reference
Face up
(3) Paper exit tray
Tray
Mode
Paper
Upper stage
Copy, printer
A3 ~ A6R
(11"
(11"
×
17" ~ 8.5
×
5.5")
Lower stage
Printer, interruption
copy
copy
A3 ~ A5
(11"
(11"
×
17" ~ 8.5
×
5.5")
(4) Power
Supplied by the copier (DC 24V)
(5) Weight
3.3 kg
J. AR-PB2
(1) General Specification
PS Specification
Platform
IBM PC/AT (or compatible)
Support OS
(Printer Drivers)
(Printer Drivers)
Custom
and PPD
and PPD
Windows 3.1/WfW3.11 (No PPD)
Windows 95/98
Windows NT 4.0
Windows 95/98
Windows NT 4.0
PDL
Emulation
Emulation
PCL5e-compatible
PostScript Level 2-Compatible
Hex Dump
PostScript Level 2-Compatible
Hex Dump
CPU
R4700 (64bit RISC / 150MHz)
Memory
Standard
16MB
Maximum
80MB (32MB SIMM x 2 + 16MB)
Slot
2 Slots (16MB / 32MB SIMM can
be attached)
be attached)
Resident Fonts
For PS
Type1: 35 fonts (Latin fonts)
For PCL
Intellifont : 35 fonts
TrueType : 10 fonts
Line Printer
Stroke Font
TrueType : 10 fonts
Line Printer
Stroke Font
Interface
IEEE1284 parallel port: 1 port
Port supports Compatible mode
(with PnP on Windows95/98).
Port supports Compatible mode
(with PnP on Windows95/98).
Extend Interface
1 Network slot on printer board.
NIC can be attached here.
NIC can be attached here.
NIC Support
DPI1.10Base-T/2 (AR-NC1D)
Port Selection
Automatic Switch or
Fix to each port
Fix to each port
Emulation Switching
Automatic Switch or
Fix to each emulation
Fix to each emulation
PnP Support
Support on Windows95/98
AR-405
1/21/1999
3 – 4
(6) Offset
Tray available
Bottom tray
Offset amount
25mm
(7) Power source
Power source
Supplied from the copier (DC 24V/DC 25)
(8) Power consumption
Max. power consumption
About 60W
(9) External view
Dimensions
590 (W)
×
560 (D)
×
998 (H)
Box color
Frosty gray
Weight
About 45kg
(10) Staple functions
Stable available
Bottom stage tray only
Face up only
Stapling
capacity
capacity
50 sheets (60g/m
2
)
(25 sheets for sizes greater than A4/8.5
×
11)
Sizes available
for stapling
for stapling
AB series
A3, B4, A4, A4R, B5, B5R
Inch series
11
×
17, 8.5
×
14, 8.5
×
13, 8.5
×
11, 8.5
×
11R
Alignment
(when stapling)
(when stapling)
Max. shift: within 1mm
Stapling
reference
reference
One position (Left rear), One position (Left
front), 2 positions (left side)
front), 2 positions (left side)
Stapler supply
Cartridge (5,000 pcs.)
Stapler
SF-SC11 (The staple cartridge case is supplied
as a service part.)
as a service part.)
Detection
Staple empty detection, no cartridge detection
Manual staple
mode
mode
Not available
I. Dual tray output unit AR-TR1
(1) Capacity
No. of bins
2 trays
Capacity
Upper stage
250 sheets
Lower stage
100 sheets
(2) Paper transport/paper exit
Paper transport
Center reference
Face up
(3) Paper exit tray
Tray
Mode
Paper
Upper stage
Copy, printer
A3 ~ A6R
(11"
(11"
×
17" ~ 8.5
×
5.5")
Lower stage
Printer, interruption
copy
copy
A3 ~ A5
(11"
(11"
×
17" ~ 8.5
×
5.5")
(4) Power
Supplied by the copier (DC 24V)
(5) Weight
3.3 kg
J. AR-PB2
(1) General Specification
PS Specification
Platform
IBM PC/AT (or compatible)
Support OS
(Printer Drivers)
(Printer Drivers)
Custom
and PPD
and PPD
Windows 3.1/WfW3.11 (No PPD)
Windows 95/98
Windows NT 4.0
Windows 95/98
Windows NT 4.0
PDL
Emulation
Emulation
PCL5e-compatible
PostScript Level 2-Compatible
Hex Dump
PostScript Level 2-Compatible
Hex Dump
CPU
R4700 (64bit RISC / 150MHz)
Memory
Standard
16MB
Maximum
80MB (32MB SIMM x 2 + 16MB)
Slot
2 Slots (16MB / 32MB SIMM can
be attached)
be attached)
Resident Fonts
For PS
Type1: 35 fonts (Latin fonts)
For PCL
Intellifont : 35 fonts
TrueType : 10 fonts
Line Printer
Stroke Font
TrueType : 10 fonts
Line Printer
Stroke Font
Interface
IEEE1284 parallel port: 1 port
Port supports Compatible mode
(with PnP on Windows95/98).
Port supports Compatible mode
(with PnP on Windows95/98).
Extend Interface
1 Network slot on printer board.
NIC can be attached here.
NIC can be attached here.
NIC Support
DPI1.10Base-T/2 (AR-NC1D)
Port Selection
Automatic Switch or
Fix to each port
Fix to each port
Emulation Switching
Automatic Switch or
Fix to each emulation
Fix to each emulation
PnP Support
Support on Windows95/98
AR-405
1/21/1999
3 – 4
(6) Offset
Tray available
Bottom tray
Offset amount
25mm
(7) Power source
Power source
Supplied from the copier (DC 24V/DC 25)
(8) Power consumption
Max. power consumption
About 60W
(9) External view
Dimensions
590 (W)
×
560 (D)
×
998 (H)
Box color
Frosty gray
Weight
About 45kg
(10) Staple functions
Stable available
Bottom stage tray only
Face up only
Stapling
capacity
capacity
50 sheets (60g/m
2
)
(25 sheets for sizes greater than A4/8.5
×
11)
Sizes available
for stapling
for stapling
AB series
A3, B4, A4, A4R, B5, B5R
Inch series
11
×
17, 8.5
×
14, 8.5
×
13, 8.5
×
11, 8.5
×
11R
Alignment
(when stapling)
(when stapling)
Max. shift: within 1mm
Stapling
reference
reference
One position (Left rear), One position (Left
front), 2 positions (left side)
front), 2 positions (left side)
Stapler supply
Cartridge (5,000 pcs.)
Stapler
SF-SC11 (The staple cartridge case is supplied
as a service part.)
as a service part.)
Detection
Staple empty detection, no cartridge detection
Manual staple
mode
mode
Not available
I. Dual tray output unit AR-TR1
(1) Capacity
No. of bins
2 trays
Capacity
Upper stage
250 sheets
Lower stage
100 sheets
(2) Paper transport/paper exit
Paper transport
Center reference
Face up
(3) Paper exit tray
Tray
Mode
Paper
Upper stage
Copy, printer
A3 ~ A6R
(11"
(11"
×
17" ~ 8.5
×
5.5")
Lower stage
Printer, interruption
copy
copy
A3 ~ A5
(11"
(11"
×
17" ~ 8.5
×
5.5")
(4) Power
Supplied by the copier (DC 24V)
(5) Weight
3.3 kg
J. AR-PB2
(1) General Specification
PS Specification
Platform
IBM PC/AT (or compatible)
Support OS
(Printer Drivers)
(Printer Drivers)
Custom
and PPD
and PPD
Windows 3.1/WfW3.11 (No PPD)
Windows 95/98
Windows NT 4.0
Windows 95/98
Windows NT 4.0
PDL
Emulation
Emulation
PCL5e-compatible
PostScript Level 2-Compatible
Hex Dump
PostScript Level 2-Compatible
Hex Dump
CPU
R4700 (64bit RISC / 150MHz)
Memory
Standard
16MB
Maximum
80MB (32MB SIMM x 2 + 16MB)
Slot
2 Slots (16MB / 32MB SIMM can
be attached)
be attached)
Resident Fonts
For PS
Type1: 35 fonts (Latin fonts)
For PCL
Intellifont : 35 fonts
TrueType : 10 fonts
Line Printer
Stroke Font
TrueType : 10 fonts
Line Printer
Stroke Font
Interface
IEEE1284 parallel port: 1 port
Port supports Compatible mode
(with PnP on Windows95/98).
Port supports Compatible mode
(with PnP on Windows95/98).
Extend Interface
1 Network slot on printer board.
NIC can be attached here.
NIC can be attached here.
NIC Support
DPI1.10Base-T/2 (AR-NC1D)
Port Selection
Automatic Switch or
Fix to each port
Fix to each port
Emulation Switching
Automatic Switch or
Fix to each emulation
Fix to each emulation
PnP Support
Support on Windows95/98
AR-405
1/21/1999
3 – 4
Display