DOWNLOAD Sharp AR-405 (serv.man30) Service Manual ↓ Size: 695.89 KB | Pages: 34 in PDF or view online for FREE

Model
AR-405 (serv.man30)
Pages
34
Size
695.89 KB
Type
PDF
Document
User Manual / Operation Manual
Brand
Device
Copying Equipment / AR405 Operation Manual-Section 1
File
ar-405-sm30.pdf
Date

Sharp AR-405 (serv.man30) User Manual / Operation Manual ▷ View online

1-3
CHAPTER
1
CAUTIONS
1.
Do not touch the photoconductive drum. Scratches or
smudges on the drum will cause dirty copies.
2.
The fusing unit is extremely hot.  Exercise care in this area.
3. Since a hard disk drive is built into the copier, be sure to turn the
power switch to the “OFF” position when moving the copier. Take
care not to subject the copier to any vibration or shock.
4.
Do not look directly  at the light source. Doing so may
damage your eyes.
5.
Four installation adjusters are provided on the optional
stand/500-sheet paper drawer.
When moving the machine with the optional stand/
500-sheet paper drawer, be sure to raise the installation
adjusters. After moving the machine, lower the four installation
adjusters until they reach the floor and lock the two casters
at the front of the copier.
6. When copying is interrupted (for example, because the
INTERRUPT function has been used, paper or toner has run out,
a misfeed has occurred, etc.), this copier will store the image
data of the originals read prior to the interruption. If copying of
secret documents is interrupted due to the above reasons, be
sure to either resume the interrupted copying by pressing the
START (
) key, or clear the image data by pressing the CLEAR
ALL (
CA
) key after the interrupt copying is completed or the
trouble is cleared, because the stored data may be printed by
other operators.
GETTING STARTED  
Cautions
Fusing unit
Photoconductive
drum
Lock
Release
Adjuster
Lock
Caster
Release
Caution
This product contains a low power laser device. To
ensure continued safety do not remove any cover or
attempt to gain access to the inside of the product. Refer
all servicing to qualified personnel.
At the production line, the output power of
the scanner unit is adjusted to 0.6 MILLI-
WATT PLUS 8 PCTS and is maintained
constant by the operation of the Automatic
Power Control (APC).
Cautions on laser
Wave length
785 nm
 +10 nm
              -15 nm
Pulse times
Europe: (3.025 µs ±3.0 ns)/7 mm
Output power
0.24 - 0.60 mW
1-4
CHAPTER
1
CAUTION
VORSICHT
ADVARSEL
ADVERSEL
VARNING
VARO!
INVISIBLE LASER RADIATION WHEN OPEN AND INTERLOCKS DEFEATED. 
AVOID EXPOSURE TO BEAM.
Laserstrahl
UNSICHTBARE LASERSTRAHLUNG WENN ABDECKUNG GEÖFFNET UND 
SICHERHEITSVERRIEGELUNG ÜBERERÜCKT. NICHT DEM STRAHL AUSSETZEN. 
USYNLIG LASERSTRÅLING VED ÅBNING, NÅR SIKKERHEDSAFBRYDERE ER 
UDE AF FUNKTION. UNDGÅ UDSAETTELSE FOR STRÅLNING.
USYNLIG LASERSTRÅLING NÅR DEKSEL ÅPNES OG SIKKERHEDSLÅS BRYTES.
UNNGÅ EKSPONERING FOR STRÅLEN.
OSYNLIG LASERSTRÅLNING NÄR DENNA DEL ÄR ÖPPNAD OCH SPÄRRAR ÄR 
URKOPPLADE. STRÅLEN ÄR FARLIG. BETRAKTA EJ STRÅLEN. 
AVATTAESSA JA SUOJALUKITUS OHITETTAESSA OLET ALTTIINA NÄKYMÄTÖNTÄ
LASERSÄTEILYLLE. ÄLÄ KATSO SÄTEESEEN. 
CAUTIONS
GETTING STARTED  
Cautions
CLASS 1 LASER PRODUCT
LASER KLASSE 1
LUOKAN 1 LASERLAITE
KLASS 1 LASERAPPARAT
CAUTION
INVISIBLE LASER RADIATION
WHEN OPEN AND INTERLOCKS
DEFEATED. AVOID EXPOSURE
TO BEAM.
VORSICHT
UNSICHTBARE
LASERSTRAHLUNG WENN
ABDECKUNG GEÖFFNET UND
SICHERHEITSVERRIEGELUNG
ÜBERBRÜCKT. NICHT DEM
STRAHL AUSSETZEN.
ADVARSEL
USYNLIG LASERSTRÅLNING
VED ÅBNING, NÅR
SIKKERHEDSBRYDERE ER UDE
AF FUNKTION. UNDGÅ
UDSAETTELSE FOR
STRÅLNING.
VAROITUS!
LAITTEEN KÄYTTÄMINEN
MUULLA KUIN TÄSSÄ
KÄYTTÖOHJEESSA MAINITULLA
TAVALLA SAATTAA ALTISTAA
KÄYTTÄJÄN
TURVALLISUUSLUOKAN 1
YLITTÄVÄLLE
NÄKYMÄTTÖMÄLLE
LASERSÄTEILYLLE.
VARNING
OM APPARATEN ANVÄNDS PÅ
ANNAT SÄTT ÄN I DENNA
BRUKSANVISNING
SPECIFICERATS, KAN
ANVÄNDAREN UTSÄTTAS FÖR
OSYNLIG LASERSTRÅLNING,
SOM ÖVERSKRIDER GRÄNSEN
FÖR LASERKLASS 1.
CLASS 1
LASER PRODUCT
LASER KLASSE 1
1-5
CHAPTER
1
POWER ON AND OFF
The power switch is located on the left side of the copier. When the
power switch is turned to the “ON” position, the message “
WARMING
UP. PLEASE WAIT.
” will appear in the message display. Warming
up takes about 65 seconds.  Once the copier is ready, the message
display will change to “
READY TO COPY.
”, and the START (
) key
indicator will light up, indicating that copying is possible.
If the copier has been programmed in the auditing mode, the message
ENTER YOUR ACCOUNT NUMBER. -----
” will appear after warming
up. Once a valid account number has been entered, copying will
become possible.
GETTING STARTED  
Power on and off
Power on
Power off
1-6
CHAPTER
1
GETTING STARTED  
Power on and off
Auto power shut-off mode
If the auto power shut-off mode is enabled, the copier will
automatically turn off the power once a programmed length of time
has elapsed without any copier operation after the last copy of a run
is made or the power is first turned on. The power switch will
automatically be turned to the “OFF” position.
To turn the power back on, simply turn the power switch to the “ON”
position.
★ KEY OPERATOR See page 8-21 for setting the auto power shut-off
timer. See page 8-26 for enabling or disabling the auto power shut-off
mode.
Preheat mode
The copier will enter the mode once the set time has elapsed without
any copier operation after the last copy of a run is made or power is
turned on.
When the copier enters the preheat mode, the message “
PREHEAT
MODE. PLACE ORIGINALS
.” will appear.
In this condition, the fuser in the copier is maintained at a lower heat
level thereby saving power. The preheat level is, however, high
enough to allow the copier to come to a ready condition or begin
copying approximately 30 seconds after any key input is made.
To copy from the preheat mode, make desired copier selections and
press the START (
) key using the normal copying procedure.
★ KEY OPERATOR See page 8-22 for information on setting the preheat
mode.
POWER ON AND OFF
Power save modes
The copier has two power save modes to reduce overall power
consumption and thereby reduce the cost of operation and to conserve
natural resources to help reduce environmental pollution. The two
power save modes are preheat mode and auto power shut-off mode.
★ KEY OPERATOR
The preheat activation time and the auto power shut-off time have been
preset at the factory to 15 min. for preheat mode and 60 min. for auto
power shut-off mode. These times can be changed as described in the key
operator’s guide section. It is suggested that you set appropriate times
according to the actual usage of the copier.
The 
E
NERGY
 
S
TAR
®
 guidelines are applied to
the products only in Europe, Australia and
New Zealand. The products that meet the
E
NERGY
 
S
TAR
®
 guidelines carry the logo
shown above. The products without the
logo may not meet the 
E
NERGY
 
S
TAR
®
guidelines.
Page of 34
Display

Click on the first or last page to see other AR-405 (serv.man30) service manuals if exist.