DOWNLOAD Sharp AR-405 (serv.man30) Service Manual ↓ Size: 695.89 KB | Pages: 34 in PDF or view online for FREE

To ensure safety and proper machine performance, please note the following
before initial installation and whenever the machine is to be relocated.

1.

The copier should be installed near an accessible power outlet for easy
connection.

2.

Be sure to connect the power cord only to a power outlet that meets the
specified voltage and current requirements.
Also make certain the outlet is properly grounded.

●

For this copier’s power supply requirements, see the name plate
located on the left hand side at the rear corner of the copier.

3.

Do not install the machine where it is:

●

damp or humid,

●

exposed to direct sunlight,

●

extremely dusty,

●

poorly ventilated,

●

subject to extreme temperature or humidity changes (e.g., near an air
conditioner or heater).

4.

Since a hard disk drive is built into this copier, place the copier on a firm,
level surface. Choose an area which is not subject to any vibration.

5.

Be sure to allow the required space around the machine for servicing and
proper ventilation.

Installation requirements

30 cm
(11-13/16")

60 cm
(23-5/8")

60 cm

(23-5/8")

30 cm

(11-13/16")

A small amount of ozone is produced within the copier during operation.
The emission level is insufficient to cause any health hazard.
NOTE:
The present recommended long term exposure limit for ozone is 0.1 ppm
(0.2 m

g

/m

3

) calculated as an 8 hr. time-weighted average concentration.

However, since the small amount that is emitted may have an objectionable
odor, it is advisable to place the copier in a ventilated area.

1.

Do not touch the photoconductive drum. Scratches or
smudges on the drum will cause dirty copies.

2.

The fusing unit is extremely hot.  Exercise care in this area.

3. Since a hard disk drive is built into the copier, be sure to turn the

power switch to the “OFF” position when moving the copier. Take
care not to subject the copier to any vibration or shock.

4.

Do not look directly  at the light source. Doing so may
damage your eyes.

5.

Four installation adjusters are provided on the optional
stand/500-sheet paper drawer.
When moving the machine with the optional stand/
500-sheet paper drawer, be sure to raise the installation
adjusters. After moving the machine, lower the four installation
adjusters until they reach the floor and lock the two casters
at the front of the copier.

6. When copying is interrupted (for example, because the

INTERRUPT function has been used, paper or toner has run out,
a misfeed has occurred, etc.), this copier will store the image
data of the originals read prior to the interruption. If copying of
secret documents is interrupted due to the above reasons, be
sure to either resume the interrupted copying by pressing the
START (

) key, or clear the image data by pressing the CLEAR

ALL (

CA

) key after the interrupt copying is completed or the

trouble is cleared, because the stored data may be printed by
other operators.

Cautions

Fusing unit

Photoconductive
drum

Lock

Release

Adjuster

Lock

Caster

Release

Caution
This product contains a low power laser device. To
ensure continued safety do not remove any cover or
attempt to gain access to the inside of the product. Refer
all servicing to qualified personnel.

At the production line, the output power of
the scanner unit is adjusted to 0.6 MILLI-
WATT PLUS 8 PCTS and is maintained
constant by the operation of the Automatic
Power Control (APC).

Wave length

785 nm

 +10 nm

              -15 nm

Pulse times

Europe: (3.025 µs ±3.0 ns)/7 mm

Output power

0.24 - 0.60 mW

CAUTION
VORSICHT
ADVARSEL
ADVERSEL
VARNING
VARO!

INVISIBLE LASER RADIATION WHEN OPEN AND INTERLOCKS DEFEATED. 
AVOID EXPOSURE TO BEAM.

Laserstrahl

UNSICHTBARE LASERSTRAHLUNG WENN ABDECKUNG GEÖFFNET UND 
SICHERHEITSVERRIEGELUNG ÜBERERÜCKT. NICHT DEM STRAHL AUSSETZEN. 

USYNLIG LASERSTRÅLING VED ÅBNING, NÅR SIKKERHEDSAFBRYDERE ER 
UDE AF FUNKTION. UNDGÅ UDSAETTELSE FOR STRÅLNING.

USYNLIG LASERSTRÅLING NÅR DEKSEL ÅPNES OG SIKKERHEDSLÅS BRYTES.
UNNGÅ EKSPONERING FOR STRÅLEN.

OSYNLIG LASERSTRÅLNING NÄR DENNA DEL ÄR ÖPPNAD OCH SPÄRRAR ÄR 
URKOPPLADE. STRÅLEN ÄR FARLIG. BETRAKTA EJ STRÅLEN. 

AVATTAESSA JA SUOJALUKITUS OHITETTAESSA OLET ALTTIINA NÄKYMÄTÖNTÄ
LASERSÄTEILYLLE. ÄLÄ KATSO SÄTEESEEN. 

Cautions

CLASS 1 LASER PRODUCT

LASER KLASSE 1

LUOKAN 1 LASERLAITE

KLASS 1 LASERAPPARAT

INVISIBLE LASER RADIATION
WHEN OPEN AND INTERLOCKS
DEFEATED. AVOID EXPOSURE
TO BEAM.

UNSICHTBARE
LASERSTRAHLUNG WENN
ABDECKUNG GEÖFFNET UND
SICHERHEITSVERRIEGELUNG
ÜBERBRÜCKT. NICHT DEM
STRAHL AUSSETZEN.

USYNLIG LASERSTRÅLNING
VED ÅBNING, NÅR
SIKKERHEDSBRYDERE ER UDE
AF FUNKTION. UNDGÅ
UDSAETTELSE FOR
STRÅLNING.

LAITTEEN KÄYTTÄMINEN
MUULLA KUIN TÄSSÄ
KÄYTTÖOHJEESSA MAINITULLA
TAVALLA SAATTAA ALTISTAA
KÄYTTÄJÄN
TURVALLISUUSLUOKAN 1
YLITTÄVÄLLE
NÄKYMÄTTÖMÄLLE
LASERSÄTEILYLLE.

OM APPARATEN ANVÄNDS PÅ
ANNAT SÄTT ÄN I DENNA
BRUKSANVISNING
SPECIFICERATS, KAN
ANVÄNDAREN UTSÄTTAS FÖR
OSYNLIG LASERSTRÅLNING,
SOM ÖVERSKRIDER GRÄNSEN
FÖR LASERKLASS 1.

The power switch is located on the left side of the copier. When the
power switch is turned to the “ON” position, the message “

” will appear in the message display. Warming

up takes about 65 seconds.  Once the copier is ready, the message
display will change to “

”, and the START (

) key

indicator will light up, indicating that copying is possible.
If the copier has been programmed in the auditing mode, the message
“

” will appear after warming

up. Once a valid account number has been entered, copying will
become possible.

Power on and off

Power on

Power off