Sharp AR-405 (serv.man30) User Manual / Operation Manual ▷ View online
2-20
CHAPTER
2
1
Press the INTERRUPT (
) key.
●
When the document feeder is being used, the copier will stop
after completing the copying of the originals which have been fed
into the document feeder. The INTERRUPT indicator will blink
until the copier becomes ready for interrupt copying.
Then the INTERRUPT indicator will light up.
The copier will return to the initial setting.
after completing the copying of the originals which have been fed
into the document feeder. The INTERRUPT indicator will blink
until the copier becomes ready for interrupt copying.
Then the INTERRUPT indicator will light up.
The copier will return to the initial setting.
●
If the copier has been programmed in the auditing mode, the
account number entry message will appear. Enter your account
number using the 10-key pad. The number of copies of the
interrupt copying will be accumulated against this account
number.
account number entry message will appear. Enter your account
number using the 10-key pad. The number of copies of the
interrupt copying will be accumulated against this account
number.
2
When the copier stops, remove the original(s) and set
the original(s) for interrupt copying in the document
feeder tray or on the document glass.
the original(s) for interrupt copying in the document
feeder tray or on the document glass.
●
The maximum number of originals for interrupt copying is
restricted.
1-sided originals: 20 sheets (10 sheets for B4 and A3 (8-1/2" x
restricted.
1-sided originals: 20 sheets (10 sheets for B4 and A3 (8-1/2" x
14" and 11" x 17"))
2-sided originals: 10 sheets (5 sheets for B4 and A3 (8-1/2" x
14" and 11" x 17"))
3
Select the desired available copier functions.
4
Press the START (
) key.
5
When the interrupt copy run is complete, press the
INTERRUPT (
INTERRUPT (
) key again to cancel the mode and
remove the original(s) used for interrupt copying.
●
The copier will reset itself to the functions which were in use
before the INTERRUPT (
) key was first pressed.
6
Replace the original(s) for the interrupted job and press
the START (
the START (
) key to resume copying.
●
If scanning of originals has been already complete, the original
need not be replaced.
need not be replaced.
MAKING COPIES
Interrupting a copy run
INTERRUPTING A COPY RUN
INTERRUPT can be used to temporarily stop a long copy run so that
another job can be run.
another job can be run.
●
INTERRUPT will not function during duplex copying.
●
Duplex copying cannot be selected during interrupt copying.
●
When an optional dual tray output unit (AR-TR1) is installed,
interrupt copies are output to the second tray of the unit.
interrupt copies are output to the second tray of the unit.
★
★
★
★
★ KEY OPERATOR
If the second tray is not installed, output of
copies to the second tray must be disabled. See page 8-26.
3
6
INTERRUPT
CA
CLE
C
CLEAR
INTERRUPT
CA
CLEAR ALL
START
3
6
INTERRUPT
CA
CLE
2-20
CHAPTER
2
1
Press the INTERRUPT (
) key.
●
When the document feeder is being used, the copier will stop
after completing the copying of the originals which have been fed
into the document feeder. The INTERRUPT indicator will blink
until the copier becomes ready for interrupt copying.
Then the INTERRUPT indicator will light up.
The copier will return to the initial setting.
after completing the copying of the originals which have been fed
into the document feeder. The INTERRUPT indicator will blink
until the copier becomes ready for interrupt copying.
Then the INTERRUPT indicator will light up.
The copier will return to the initial setting.
●
If the copier has been programmed in the auditing mode, the
account number entry message will appear. Enter your account
number using the 10-key pad. The number of copies of the
interrupt copying will be accumulated against this account
number.
account number entry message will appear. Enter your account
number using the 10-key pad. The number of copies of the
interrupt copying will be accumulated against this account
number.
2
When the copier stops, remove the original(s) and set
the original(s) for interrupt copying in the document
feeder tray or on the document glass.
the original(s) for interrupt copying in the document
feeder tray or on the document glass.
●
The maximum number of originals for interrupt copying is
restricted.
1-sided originals: 20 sheets (10 sheets for B4 and A3 (8-1/2" x
restricted.
1-sided originals: 20 sheets (10 sheets for B4 and A3 (8-1/2" x
14" and 11" x 17"))
2-sided originals: 10 sheets (5 sheets for B4 and A3 (8-1/2" x
14" and 11" x 17"))
3
Select the desired available copier functions.
4
Press the START (
) key.
5
When the interrupt copy run is complete, press the
INTERRUPT (
INTERRUPT (
) key again to cancel the mode and
remove the original(s) used for interrupt copying.
●
The copier will reset itself to the functions which were in use
before the INTERRUPT (
) key was first pressed.
6
Replace the original(s) for the interrupted job and press
the START (
the START (
) key to resume copying.
●
If scanning of originals has been already complete, the original
need not be replaced.
need not be replaced.
MAKING COPIES
Interrupting a copy run
INTERRUPTING A COPY RUN
INTERRUPT can be used to temporarily stop a long copy run so that
another job can be run.
another job can be run.
●
INTERRUPT will not function during duplex copying.
●
Duplex copying cannot be selected during interrupt copying.
●
When an optional dual tray output unit (AR-TR1) is installed,
interrupt copies are output to the second tray of the unit.
interrupt copies are output to the second tray of the unit.
★
★
★
★
★ KEY OPERATOR
If the second tray is not installed, output of
copies to the second tray must be disabled. See page 8-26.
3
6
INTERRUPT
CA
CLE
C
CLEAR
INTERRUPT
CA
CLEAR ALL
START
3
6
INTERRUPT
CA
CLE
2-20
CHAPTER
2
1
Press the INTERRUPT (
) key.
●
When the document feeder is being used, the copier will stop
after completing the copying of the originals which have been fed
into the document feeder. The INTERRUPT indicator will blink
until the copier becomes ready for interrupt copying.
Then the INTERRUPT indicator will light up.
The copier will return to the initial setting.
after completing the copying of the originals which have been fed
into the document feeder. The INTERRUPT indicator will blink
until the copier becomes ready for interrupt copying.
Then the INTERRUPT indicator will light up.
The copier will return to the initial setting.
●
If the copier has been programmed in the auditing mode, the
account number entry message will appear. Enter your account
number using the 10-key pad. The number of copies of the
interrupt copying will be accumulated against this account
number.
account number entry message will appear. Enter your account
number using the 10-key pad. The number of copies of the
interrupt copying will be accumulated against this account
number.
2
When the copier stops, remove the original(s) and set
the original(s) for interrupt copying in the document
feeder tray or on the document glass.
the original(s) for interrupt copying in the document
feeder tray or on the document glass.
●
The maximum number of originals for interrupt copying is
restricted.
1-sided originals: 20 sheets (10 sheets for B4 and A3 (8-1/2" x
restricted.
1-sided originals: 20 sheets (10 sheets for B4 and A3 (8-1/2" x
14" and 11" x 17"))
2-sided originals: 10 sheets (5 sheets for B4 and A3 (8-1/2" x
14" and 11" x 17"))
3
Select the desired available copier functions.
4
Press the START (
) key.
5
When the interrupt copy run is complete, press the
INTERRUPT (
INTERRUPT (
) key again to cancel the mode and
remove the original(s) used for interrupt copying.
●
The copier will reset itself to the functions which were in use
before the INTERRUPT (
) key was first pressed.
6
Replace the original(s) for the interrupted job and press
the START (
the START (
) key to resume copying.
●
If scanning of originals has been already complete, the original
need not be replaced.
need not be replaced.
MAKING COPIES
Interrupting a copy run
INTERRUPTING A COPY RUN
INTERRUPT can be used to temporarily stop a long copy run so that
another job can be run.
another job can be run.
●
INTERRUPT will not function during duplex copying.
●
Duplex copying cannot be selected during interrupt copying.
●
When an optional dual tray output unit (AR-TR1) is installed,
interrupt copies are output to the second tray of the unit.
interrupt copies are output to the second tray of the unit.
★
★
★
★
★ KEY OPERATOR
If the second tray is not installed, output of
copies to the second tray must be disabled. See page 8-26.
3
6
INTERRUPT
CA
CLE
C
CLEAR
INTERRUPT
CA
CLEAR ALL
START
3
6
INTERRUPT
CA
CLE
2-20
CHAPTER
2
1
Press the INTERRUPT (
) key.
●
When the document feeder is being used, the copier will stop
after completing the copying of the originals which have been fed
into the document feeder. The INTERRUPT indicator will blink
until the copier becomes ready for interrupt copying.
Then the INTERRUPT indicator will light up.
The copier will return to the initial setting.
after completing the copying of the originals which have been fed
into the document feeder. The INTERRUPT indicator will blink
until the copier becomes ready for interrupt copying.
Then the INTERRUPT indicator will light up.
The copier will return to the initial setting.
●
If the copier has been programmed in the auditing mode, the
account number entry message will appear. Enter your account
number using the 10-key pad. The number of copies of the
interrupt copying will be accumulated against this account
number.
account number entry message will appear. Enter your account
number using the 10-key pad. The number of copies of the
interrupt copying will be accumulated against this account
number.
2
When the copier stops, remove the original(s) and set
the original(s) for interrupt copying in the document
feeder tray or on the document glass.
the original(s) for interrupt copying in the document
feeder tray or on the document glass.
●
The maximum number of originals for interrupt copying is
restricted.
1-sided originals: 20 sheets (10 sheets for B4 and A3 (8-1/2" x
restricted.
1-sided originals: 20 sheets (10 sheets for B4 and A3 (8-1/2" x
14" and 11" x 17"))
2-sided originals: 10 sheets (5 sheets for B4 and A3 (8-1/2" x
14" and 11" x 17"))
3
Select the desired available copier functions.
4
Press the START (
) key.
5
When the interrupt copy run is complete, press the
INTERRUPT (
INTERRUPT (
) key again to cancel the mode and
remove the original(s) used for interrupt copying.
●
The copier will reset itself to the functions which were in use
before the INTERRUPT (
) key was first pressed.
6
Replace the original(s) for the interrupted job and press
the START (
the START (
) key to resume copying.
●
If scanning of originals has been already complete, the original
need not be replaced.
need not be replaced.
MAKING COPIES
Interrupting a copy run
INTERRUPTING A COPY RUN
INTERRUPT can be used to temporarily stop a long copy run so that
another job can be run.
another job can be run.
●
INTERRUPT will not function during duplex copying.
●
Duplex copying cannot be selected during interrupt copying.
●
When an optional dual tray output unit (AR-TR1) is installed,
interrupt copies are output to the second tray of the unit.
interrupt copies are output to the second tray of the unit.
★
★
★
★
★ KEY OPERATOR
If the second tray is not installed, output of
copies to the second tray must be disabled. See page 8-26.
3
6
INTERRUPT
CA
CLE
C
CLEAR
INTERRUPT
CA
CLEAR ALL
START
3
6
INTERRUPT
CA
CLE
