DOWNLOAD Sharp AR-405 (serv.man30) Service Manual ↓ Size: 695.89 KB | Pages: 34 in PDF or view online for FREE

Model
AR-405 (serv.man30)
Pages
34
Size
695.89 KB
Type
PDF
Document
User Manual / Operation Manual
Brand
Device
Copying Equipment / AR405 Operation Manual-Section 1
File
ar-405-sm30.pdf
Date

Sharp AR-405 (serv.man30) User Manual / Operation Manual ▷ View online

2
1.8/ 11
2.11 17
1
2
8/ 11R
1
2
[Inch series]
[AB series]
1. A4
2.
 
A3
ORIGINAL
A4R
INTRODUCTION
The AR-405 copier is digital image processing copier which provides high productivity and convenient features
including intelligent image-editing functions.
Amongst its many useful features and functions are the document feeder, various special functions such as dual page
copying, margin shift, erase, XY zoom, and black and white reverse functions, photo copying, and an internal auditor.
The digital processing system of the copier allows multiple sets of copies to be sorted without the aid of a sorter. This
copier can be equipped with an optional large capacity tray which holds 3,000 sheets of copy paper. The machine
can also be equipped with an optional finisher to provide finished copy sets ready for distribution.
This copier was also designed with ease of use in mind. The easy-to-understand operation panel with touch panel
system and INFORMATION function will guide the user through most operations. However, to gain the maximum
benefit of all the features of the copier, it is recommended that users first read this manual to become familiar with
all the features of the copier.
NOTES:
This manual describes only copier features. For a description of optional printer features, see the separate relevant
manual.
USING THIS  MANUAL
This manual is intended as an operation guide for both general users and key operators.
For General Users
It is recommended that you read the GETTING STARTED, MAKING COPIES, and SPECIAL FUNCTIONS sections
to become familiar with the available features and functions of your copier. Then refer to the manual as needed to
become thoroughly familiar with those features you will normally use.
For Key Operators
Please read all sections thoroughly to become familiar with all features and functions of your copier. Throughout the
manual, information which is relevant to key operator functions is noted by “
 
KEY OPERATOR.
” Please pay close
attention to these notes and to the SUPPLIES, COPIER TROUBLE?, GENERAL INFORMATION, and OPTIONAL
EQUIPMENT sections so you can ensure smooth and efficient operation of your machine.
The KEY OPERATOR’S GUIDE section has been written especially for you. It contains the programs and
programming information that will enable you to tailor functions for maximum benefit
to your company.
AB series (metric) and inch series references
Both specifications are quoted where applicable.
The inch series specifications are quoted in brackets.
For example:
Page 2-3, Notes on the RADF -------------- A5 to A4 (5-1/2" x 8-1/2" to 8-1/2" x 11")
Page 2-12, step 3, Menu 1-A ---------------- 86%, 81%, and 70% (77% and 64%)
Although AB series size indications are shown on the touch panel of this manual,
inch series indications are displayed on the inch series machines.
1-1
CHAPTER
1
CHAPTER 1
GETTING STARTED
This chapter describes the basic information on the use of this copier.
                                    
  
Page
INSTALLATION REQUIREMENTS
.....................
1-2
CAUTIONS
......................................
1-3
POWER ON AND OFF
..............................
1-5
Power save modes
..................................
1-6
INFORMATION FUNCTION
............................
1-7
USING THE TOUCH  PANEL
...........................
1-8
How to use the touch panel
............................
1-8
Selection of function
.................................
1-8
Function setting icons
................................
1-9
1-2
CHAPTER
1
INSTALLATION REQUIREMENTS
To ensure safety and proper machine performance, please note the following
before initial installation and whenever the machine is to be relocated.
1.
The copier should be installed near an accessible power outlet for easy
connection.
2.
Be sure to connect the power cord only to a power outlet that meets the
specified voltage and current requirements.
Also make certain the outlet is properly grounded.
For this copier’s power supply requirements, see the name plate
located on the left hand side at the rear corner of the copier.
3.
Do not install the machine where it is:
damp or humid,
exposed to direct sunlight,
extremely dusty,
poorly ventilated,
subject to extreme temperature or humidity changes (e.g., near an air
conditioner or heater).
4.
Since a hard disk drive is built into this copier, place the copier on a firm,
level surface. Choose an area which is not subject to any vibration.
5.
Be sure to allow the required space around the machine for servicing and
proper ventilation.
GETTING STARTED  
Installation requirements
30 cm
(11-13/16")
60 cm
(23-5/8")
60 cm
(23-5/8")
30 cm
(11-13/16")
A small amount of ozone is produced within the copier during operation.
The emission level is insufficient to cause any health hazard.
NOTE:
The present recommended long term exposure limit for ozone is 0.1 ppm
(0.2 m
g
/m
3
) calculated as an 8 hr. time-weighted average concentration.
However, since the small amount that is emitted may have an objectionable
odor, it is advisable to place the copier in a ventilated area.
1-3
CHAPTER
1
CAUTIONS
1.
Do not touch the photoconductive drum. Scratches or
smudges on the drum will cause dirty copies.
2.
The fusing unit is extremely hot.  Exercise care in this area.
3. Since a hard disk drive is built into the copier, be sure to turn the
power switch to the “OFF” position when moving the copier. Take
care not to subject the copier to any vibration or shock.
4.
Do not look directly  at the light source. Doing so may
damage your eyes.
5.
Four installation adjusters are provided on the optional
stand/500-sheet paper drawer.
When moving the machine with the optional stand/
500-sheet paper drawer, be sure to raise the installation
adjusters. After moving the machine, lower the four installation
adjusters until they reach the floor and lock the two casters
at the front of the copier.
6. When copying is interrupted (for example, because the
INTERRUPT function has been used, paper or toner has run out,
a misfeed has occurred, etc.), this copier will store the image
data of the originals read prior to the interruption. If copying of
secret documents is interrupted due to the above reasons, be
sure to either resume the interrupted copying by pressing the
START (
) key, or clear the image data by pressing the CLEAR
ALL (
CA
) key after the interrupt copying is completed or the
trouble is cleared, because the stored data may be printed by
other operators.
GETTING STARTED  
Cautions
Fusing unit
Photoconductive
drum
Lock
Release
Adjuster
Lock
Caster
Release
Caution
This product contains a low power laser device. To
ensure continued safety do not remove any cover or
attempt to gain access to the inside of the product. Refer
all servicing to qualified personnel.
At the production line, the output power of
the scanner unit is adjusted to 0.6 MILLI-
WATT PLUS 8 PCTS and is maintained
constant by the operation of the Automatic
Power Control (APC).
Cautions on laser
Wave length
785 nm
 +10 nm
              -15 nm
Pulse times
Europe: (3.025 µs ±3.0 ns)/7 mm
Output power
0.24 - 0.60 mW
Page of 34
Display

Sharp AR-405 (serv.man30) User Manual / Operation Manual ▷ Download

  • DOWNLOAD Sharp AR-405 (serv.man30) Service Manual ↓ Size: 695.89 KB | Pages: 34 in PDF or view online for FREE
  • Here you can View online or download the User Manual / Operation Manual for the Sharp AR-405 (serv.man30) in PDF for free, which will help you to disassemble, recover, fix and repair Sharp AR-405 (serv.man30) Copying Equipment. Information contained in Sharp AR-405 (serv.man30) User Manual / Operation Manual (repair manual) includes:
  • Disassembly, troubleshooting, maintenance, adjustment, installation and setup instructions.
  • Schematics, Circuit, Wiring and Block diagrams.
  • Printed wiring boards (PWB) and printed circuit boards (PCB).
  • Exploded View and Parts List.